| Gas Pressure Switch | This switch is located inside the gas valve and should |
|
| close when gas pressure is present. WITH POWER |
|
| OFF: remove 3 prong plug (on gas valve) and |
|
| measure continuity between terminals 2 and 3.NOTE: |
|
| Remove insulation pad below plug to read numbers. If |
|
| no continuity, check the following: |
|
| 1. Proper gas pressure supply to the gas valve as |
|
| marked on the oven specification plate. |
|
| 2. Check for proper adjustment of gas pressure |
|
| switch. 8.8 on dial for natural gas, 23 for LP, and 4.5 |
|
| for Town Gas. |
|
| 3. Check gas filter in gas valve for blockage or |
|
| damage. (See Adjustment Section on page 28). If |
|
| above checks are okay, but pressure switch is still not |
|
| closed, replace gas valve. |
| Thermostat is normally closed, opens at 368°C | |
|
| (695°F). If open, reset and test oven for proper |
|
| operation. If thermostat will not hold for maximum |
|
| oven temperature, and oven is not exceeding |
|
| temperature dial setting, check for proper location of |
|
| capillary bulb in its spring holder. If above checks |
|
| okay, replace |
| Ignition Control | Check for proper line voltage supply to ignition control, |
|
| terminal #1.Check for proper line voltage to the Burner |
|
| Blower Motor. If voltage is present, proceed with next |
|
| step, if not, wait 30 seconds, push reset button, and |
|
| try to restart. If this fails, check wires from thermostat |
|
| and burner blower motor to the ignition control. If all |
|
| above fails and wires are okay, replace ignition |
|
| control. |
| Burner Blower Motor | Check for line voltage to motor. WITH POWER OFF: |
|
| turn blower wheel to check for locked rotor or blower |
|
| wheel slippage. If proper line voltage is present at |
|
| motor connecting plug, terminal 2 and 5, and motor |
|
| does not run, replace motor. |
| Air Pressure Switch (Burner | Check for proper line voltage switching from "N.C." to |
| Blower) | "N.O." as air pressure switch closes. Check for air |
|
| switch adjustment, air tube blockage, or misalignment, |
|
| and if these fail, replace air pressure switch. |
| Spark Generator | A |
|
| blower motor starts, check for proper line voltage at |
|
| spark generator. If voltage is not present, check reset |
|
| button for the Ignition Control. If voltage is still not |
|
| present, replace ignition control. If voltage is present, |
|
| visually check for spark at igniter head located in end |
|
| of burner. |
| Igniter/Sensor Assembly | Check this assembly for visible damage. If there is no |
|
| damage, replace the spark generator. If there is |
|
| damage, replace the Igniter/Sensor Assembly. Also |
|
| check for frayed or damaged wires in the burner tube. |
|
| Check spark gap (should be .100 inch 2.5 mm). |
|
| Replace as needed. |
| Gas valve | This solenoid is located inside the gas valve and |
|
| should open when proper line voltage is present. If no |
|
| voltage is present, check the reset button on the |
|
| ignition control, and all connections for tightness. If |
|
| there is still no voltage present at gas valve, replace |
|
| ignition control. If there is voltage present, check for |
|
| gas pressure at the gas pressure tap located in the |
|
| gas piping just prior to the burner. If there is no gas |
|
| pressure, replace gas valve. |
Impinger I – 1400 Series Advantage Service Manual – Dom & Int’l | 15 |