Bunn DUAL068000 manual Funnel Detect, Service Tools, Left Brew Valve

Page 33

PROGRAMMING THE BREWER (cont.)

FUNNEL DETECT (optional)

This function allows the operator to prevent the start of a brew cycle if a Smart Funnel is not positioned correctly in the funnel rails.

FUNNEL DETECT ?

NO DONE YES

Procedure to set funnel detect:

1.Press and hold the upper right hidden switch until display reads UNITS. Release the switch. Continue to press and release switch until display reads

FUNNEL DETECT.

2.NO or YES should be flashing to indicate the cur-

rent setting.

4.Select YES to prevent brewing if a Smart Funnel is not correctly situated in the rails. If this function is activated and a brew cycle is attempted with the funnel not properly situated, the display will read, FUNNEL NOT IN PLACE, until one is in place.

5.Select NO to allow brewing without a Smart Fun- nel in place. This is selected when brewing with a funnel other than a Smart Funnel (a regular brew funnel).

6.When finished, press and release DONE. This will retain the changes, exit this function screen and advance to the next. Another alternative is to press the ON/OFF switch (either on DUAL brewers) lo- cated on the front switch panel to exit the FUNNEL DETECT and return to the MAIN SCREEN.

SERVICE TOOLS

This function allows the testing of individual com- ponents and the ability to check switches for proper function. This function also tests the Soft Heat server's status on the brewer (in place or removed), and the funnel sensor coil's frequency (diagnostic tool for troubleshooting purposes only).

Testing individual components (outputs):

This will allow the operator to test the operation of individual components and outputs of the brewer. The components that can be individually tested are as follows:

SINGLE Brewers

DUAL Brewers

Brew Valve

Left Brew Valve

Bypass Valve

Left Bypass Valve

Funnel Lock (Optional)

Left Funnel Lock

Refill Valve

Right Brew Valve

Tank Heaters

Right Bypass Valve

Heater Contactor

Right Funnel Lock

 

Refill Valve

 

Tank Heaters

 

Heater Contactor

Procedure to test components (outputs):

1.Place brew funnels into rails on both sides of brewer.

2.Place a server beneath each brew funnel.

3.Press and hold the upper right hidden switch until display reads UNITS. Release the switch. Continue to press and release switch until SERVICE TOOLS appears.

4.Press YES to run tests on various components and outputs within the brewer. Pressing NO will exit this function and advance to the next function screen.

5.The display should read TEST OUTPUTS.

6.Press and release YES. The display should read

LEFT BREW VALVE.

7.To test LEFT BREW VALVE, press ON. If the brew valve is functional, water should run from the left brew side.

8.Press OFF to end flow of water.

9.Press NEXT to advance to the next component to be tested.

Page 33

41342 080108

 

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Dualtf DBC BUNN-O-MATIC Commercial Product Warranty Introduction Glossary Programming Programming SwitchesScreen Programming Lockout Switch mounted on main control boardOutputs Main Screen Brew LockoutProgram Functions Level RecipesDRIP-OUT Times Continue to LevelProgramming the Brewer Program Flow DiagramProgram Flow Diagram Procedure for modifying units of measure Units Setting Units of MeasureProcedure for Setting the Recipe SET NEW RecipeRecipe Sizes DONE? SET NEW RecipeProcedure to program the coffee name Review RECIPES? No YES Procedure for reviewing recipes Review RECIPES/MODIFY RECIPES/SET UP no Name Coffee FavorsReview Recipes WAS the Last RecipeReview RECIPES? Noyes Brew OZ Setting or Adjusting Brew VOL- UmesBypass Modifying pulse brew SET Pulse BrewNO-NAME Left Modify Show Next SET Pulse BrewSET Pulse Brew Easy Pulse Setup SET Pulse Brew Enter Times TIMES?DONE? Batches DONE? SET PreinfusionProcedure to modify drip times Setup CompleteDrip Time now displayed on non funnel lock units as well Copy Settings no Name Coffee Settings only Procedure to assign recipesProcedure to copy settings Assign RecipesYOU SURE? Enable ADS?Are YOU SURE? SET TempSET Temp Procedure to set ready temperatureSET Ready Refill Range 20 toProcedure to adjust the flow rate setting Spray OZ/M Single BrewersSpray OZ/M Dual Brewers Bypass OZ/M Dual Brewers Bypass OZ/M Single BrewersProcedures to calibrate the sprayhead flow rate Calibrate FlowCalibrate Flow ? Brate Bypass .. Press Brew to Start Calibrate Flow Procedures to calibrate the bypass flow rateBrew Counters Procedures to view/reset the brew countersService Tools Funnel DetectLeft Brew Valve Procedure to test switches Service ToolsProcedures to test coil frequency Nothing PressedYES Main Screen Factory Defaults Procedure to set factory defaultsFREQUENCY?
Related manuals
Manual 10 pages 56.74 Kb Manual 9 pages 50.59 Kb

DUAL068000 specifications

The Bunn DUAL068000 is an advanced commercial coffee maker designed for high-volume environments where speed, efficiency, and quality are paramount. This dual-brew coffee maker seamlessly combines performance with innovative technologies to meet the demands of cafes, restaurants, and convenience stores.

One of the standout features of the DUAL068000 is its dual brewing capabilities. It allows for the simultaneous brewing of two different types of coffee. This flexibility is particularly valuable in busy settings where diverse customer preferences must be accommodated. Operators can brew a full pot of drip coffee while simultaneously preparing a specialty coffee drink, optimizing workflow and minimizing wait times.

Equipped with a powerful heating element, this coffee maker can brew a full 12-cup pot in under four minutes. This rapid brewing time ensures that fresh coffee is always available, keeping customers satisfied and coming back for more. The DUAL068000 utilizes a unique hot water faucet that provides water on demand, making it easy to prepare tea or other hot beverages without disruption to the brewing process.

The DUAL068000 incorporates Bunn’s patented brewing technology, which includes temperature control and precision brewing features. The machine maintains consistency in water temperature throughout the brewing cycle, ensuring optimal extraction and rich flavor profiles in every cup. Its adjustable brew time allows operators to customize the strength of their coffee according to specific needs.

In terms of durability, the Bunn DUAL068000 is built to withstand the rigors of commercial use. Made from high-quality stainless steel, it offers a robust design that is both easy to clean and resistant to wear and tear over time. The easy-to-navigate control panel provides intuitive operation, allowing staff to quickly adjust settings without extensive training.

Another key characteristic of this machine is its energy-efficient design. Bunn has incorporated features that minimize energy consumption while maximizing output, making the DUAL068000 an eco-friendly choice for coffee businesses seeking to reduce their carbon footprint.

Overall, the Bunn DUAL068000 coffee maker combines reliability, efficiency, and flexibility, making it an ideal choice for any establishment looking to serve exceptional coffee quickly and efficiently. Its advanced technology and robust build quality position it as a leader in the commercial coffee maker market.
Top Page Image Contents