Bunn DUAL068000 manual Frequency?, Main Screen Factory Defaults, Procedure to set factory defaults

Page 36

PROGRAMMING THE BREWER (cont.)

SERVICE TOOLS (cont.)

the next function screen. Press YES to run tests on various components and outputs within the brewer.

5.The display should read TEST OUTPUTS?.

6.In TEST OUTPUTS screen, press NO. Continue to press and release NO until the display reads TEST

FREQUENCY?.

7.Press and release YES. The display will show the frequency of the sensor coil circuits. This is for diagnostic service use when troubleshooting this circuit.

8.After the coils have been tested, press and release the ON/OFF switch (either on DUAL brewers) located on the front switch panel. This will exit the TEST FREQUENCY function and return to the

MAIN SCREEN.

NOTE: If the operator wishes to test more than one function in the SERVICE TOOLS section (outputs, switches, servers, or coil frequency), it is not necessary to exit the program. Use the flow chart for SERVICE TOOLS to navigate to a particular function.

FACTORY DEFAULTS

This function allows the operator to erase all of the previously entered recipes and ad messages. Factory- set default values will replace all previous settings.

SEL BREWER TYPE?

NOYES

ThermoF SoftHeat

DONE

FACTORY DEFAULTS

NOYES

EXIT

WILL REPLACE ALL

BREW SETTINGS

ARE YOU SURE?

NOYES

EXIT

 

 

 

 

P2312

 

 

 

 

 

REPLACE

Procedure to set factory defaults:

1.Press and hold the upper right hidden switch until UNITS appears. Release the switch. Press and release the upper right hidden switch until the display reads SEL BREWER TYPE?.

2.Pressing NO in this screen will advance to FACTORY DEFAULTS. Press and release YES. The display should read ThermoF SoftHeat. The selected brewer type will be flashing. When correct brewer type is selected press DONE.

3.The display should now read FACTORY DEFAULTS. Pressing NO in this screen will revert to the MAIN SCREEN. Press YES to replace the defaults. This advances to WILL REPLACE ALL BREWING SET- TINGS. This screen will alternate with ARE YOU SURE?.

4.Pressing NO in the confirmation screen will revert to MAIN SCREEN, without resetting the brewing setups to the defaults. Press YES to load the de- faults. This will then revert to the MAIN SCREEN, and the factory default values will replace all previously entered values. It will NOT reset the summation Brew counter.

Page 36

41342 080108

 

Page 35 Page 36
Image 36
Page 35 Page 36
Contents Dualtf DBC BUNN-O-MATIC Commercial Product Warranty Introduction Glossary Programming Switches ProgrammingProgramming Lockout Switch mounted on main control board ScreenOutputs Main Screen Brew LockoutProgram Functions Level RecipesDRIP-OUT Times Level Continue toProgram Flow Diagram Programming the BrewerProgram Flow Diagram Units Setting Units of Measure Procedure for modifying units of measureProcedure for Setting the Recipe SET NEW RecipeRecipe SET NEW Recipe Sizes DONE?Procedure to program the coffee name Review RECIPES? No YES Review RECIPES/MODIFY RECIPES/SET UP no Name Coffee Favors Procedure for reviewing recipesReview Recipes WAS the Last RecipeBrew OZ Setting or Adjusting Brew VOL- Umes Review RECIPES? NoyesBypass SET Pulse Brew Modifying pulse brewSET Pulse Brew NO-NAME Left Modify Show NextSET Pulse Brew Easy Pulse Setup SET Pulse Brew Enter Times TIMES?DONE? SET Preinfusion Batches DONE?Procedure to modify drip times Setup CompleteDrip Time now displayed on non funnel lock units as well Procedure to assign recipes Copy Settings no Name Coffee Settings onlyProcedure to copy settings Assign RecipesEnable ADS? YOU SURE?Are YOU SURE? SET TempProcedure to set ready temperature SET TempSET Ready Refill Range 20 toProcedure to adjust the flow rate setting Spray OZ/M Single BrewersSpray OZ/M Dual Brewers Bypass OZ/M Single Brewers Bypass OZ/M Dual BrewersProcedures to calibrate the sprayhead flow rate Calibrate FlowCalibrate Flow ? Calibrate Flow Procedures to calibrate the bypass flow rate Brate Bypass .. Press Brew to StartProcedures to view/reset the brew counters Brew CountersService Tools Funnel DetectLeft Brew Valve Service Tools Procedure to test switchesProcedures to test coil frequency Nothing PressedYES Main Screen Factory Defaults Procedure to set factory defaultsFREQUENCY?
Related manuals
Manual 10 pages 56.74 Kb Manual 9 pages 50.59 Kb

DUAL068000 specifications

The Bunn DUAL068000 is an advanced commercial coffee maker designed for high-volume environments where speed, efficiency, and quality are paramount. This dual-brew coffee maker seamlessly combines performance with innovative technologies to meet the demands of cafes, restaurants, and convenience stores.

One of the standout features of the DUAL068000 is its dual brewing capabilities. It allows for the simultaneous brewing of two different types of coffee. This flexibility is particularly valuable in busy settings where diverse customer preferences must be accommodated. Operators can brew a full pot of drip coffee while simultaneously preparing a specialty coffee drink, optimizing workflow and minimizing wait times.

Equipped with a powerful heating element, this coffee maker can brew a full 12-cup pot in under four minutes. This rapid brewing time ensures that fresh coffee is always available, keeping customers satisfied and coming back for more. The DUAL068000 utilizes a unique hot water faucet that provides water on demand, making it easy to prepare tea or other hot beverages without disruption to the brewing process.

The DUAL068000 incorporates Bunn’s patented brewing technology, which includes temperature control and precision brewing features. The machine maintains consistency in water temperature throughout the brewing cycle, ensuring optimal extraction and rich flavor profiles in every cup. Its adjustable brew time allows operators to customize the strength of their coffee according to specific needs.

In terms of durability, the Bunn DUAL068000 is built to withstand the rigors of commercial use. Made from high-quality stainless steel, it offers a robust design that is both easy to clean and resistant to wear and tear over time. The easy-to-navigate control panel provides intuitive operation, allowing staff to quickly adjust settings without extensive training.

Another key characteristic of this machine is its energy-efficient design. Bunn has incorporated features that minimize energy consumption while maximizing output, making the DUAL068000 an eco-friendly choice for coffee businesses seeking to reduce their carbon footprint.

Overall, the Bunn DUAL068000 coffee maker combines reliability, efficiency, and flexibility, making it an ideal choice for any establishment looking to serve exceptional coffee quickly and efficiently. Its advanced technology and robust build quality position it as a leader in the commercial coffee maker market.
Top Page Image Contents