Henny Penny OE-100 manual Heating Elements, Replacement

Page 6

Henny Penny

2-6. HEATING ELEMENTS (Continued)

Model OE-100

Replacement

1.Drain the shortening from the frypot.

2.Remove the heating element wire from the terminals by removing the nuts and washer. Label each so it can be replaced in the same position on the new element.

3.Remove the retainer securing the silicone gasket.

4.Loosen the bolts on the four element spreaders.

5.Slide the element spreaders to the center of the heating element.

6.Remove the brass nuts (4) and washers (3) which secure the ends of the elements through the frypot wall.

7.Remove the heating elements from the frypot as a group by lifting the far end and sliding them up and out toward the rear of the frypot.

8.Install new heating elements with new "0" rings (2) mounted on terminal ends and spreaders loosely mounted in the center of the heating elements.

9.Replace the heating elements, terminal end first, at approximately 450 angle, slipping the terminal ends through the front end of the frypot.

10.Replace the brass nuts (4) and washers (3) on the heating element terminals. Tighten the brass nuts to 30 foot pounds of torque.

11.Move the element spreader from the center of the element into a position which will spread each element apart evenly on all four sides and tighten.

12.Reconnect the wires to the appropriate terminal as labeled when they were removed.

13.Replace the front control panel.

14.Connect the power cord to the wall receptacle or close wall circuit breaker.

Heating elements should never be energized without short- ening in frypot.

15.Replace the shortening in the frypot.

1091

2-6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Removing IntroductionTest Instruments Control PanelRemoving the Control Panel Thermal SensorHigh Temperature Limit Control Thermal SensorHigh Temperature High Temperature Limit ControlHeating Elements Replacement Heating ElementsContactors Test Points Results Heat ContactorTest Points Results Primary Contactor Test Points Results Place ON/OFF switch to the OFF position and unplugPower cord to open the wall circuit breaker FANCOOK/PUMP Switch Checkout ReplacementDrain Switch FusesFilter Heater Switch Filter Heater Through this filter rinse hose. Heat causes the rubber hose Shortening with temperature in excess of 200 of flowsHose assembly leaks or ruptures To age and deteriorate. The hose and fittings should beFilter Valve Filter PumpMotor in any other position could cause damage to When removing a pump from a motor note the positionsFryer. There is an indicator on the side of the two halves Pump, this mark must be together and face to the frontPumpand Motor ReplacementMaintenance Cooling FANRestore power to unit and unit is now ready for operation Fuse, or electrical shock could resultHenny Penny Model OE-100 994 1197 Henny Penny Model OE-100 Henny Penny Model OE-100 694 Henny Penny Model OE-100 1294

OE-100 specifications

The Henny Penny OE-100 is a premier commercial pressure fryer that stands out in the fast-food and restaurant industries for its efficiency, versatility, and superior frying capabilities. Designed to enhance the cooking process, the OE-100 brings innovation and reliability to kitchens, making it an essential tool for operators looking to serve high-quality fried foods consistently.

One of the key features of the Henny Penny OE-100 is its advanced frying technology. The pressure frying system allows for faster cooking times while sealing in moisture and flavor. This technology not only produces crispy, golden-brown fried products but also helps to reduce the amount of oil absorption, leading to healthier meal options. The pressure cooking process shortens the cooking time by using pressurized steam, which raises the boiling point of water. This means foods can be cooked quickly without compromising texture or taste.

Another notable characteristic of the OE-100 is its energy efficiency. The fryer is designed to use less oil, making it environmentally friendly and cost-effective. Additionally, the machine incorporates insulation that minimizes heat loss, which optimizes energy consumption. This is particularly beneficial for high-volume operations where reducing operational costs is crucial.

The OE-100 also features user-friendly controls, making it easy for operators to set precise cooking times and temperatures. This precision promotes consistency in food quality, ensuring that every batch of fried products meets a restaurant's high standards. Safety is another priority in the design of the OE-100, which includes features such as a built-in safety valve, automatic lid locking mechanisms, and cool-to-the-touch exteriors to minimize the risk of burns which are common in commercial frying operations.

Furthermore, the Henny Penny OE-100 is made with durable materials, ensuring longevity in rugged kitchen environments. Its compact design allows it to fit into various kitchen layouts, while still providing ample frying capacity.

Overall, the Henny Penny OE-100 stands as a benchmark in pressure frying technology, combining advanced features, energy efficiency, and safety to deliver exceptional results in commercial kitchens. Its ability to produce delicious, high-quality fried foods makes it a favorite among culinary professionals.
Top Page Image Contents