Henny Penny OE-100 manual Thermal Sensor, High Temperature Limit Control

Page 3

Henny Penny

Model OE-100

2-4. THERMAL SENSOR (Continued)

2-5. HIGH TEMPERATURE

LIMIT CONTROL

4.Unplug electrical wires from control panel board that are attached to thermal sensor.

5.Using a 1/2" wrench, loosen screw nut from pot fitting and pull thermal sensor bulb straight out from pot fitting.

6.Install new thermal sensor, making sure the thermal sensor ex- tends through pot wall, up to the outer diameter of the heating element.

Care must be taken not to extend the thermal sensor beyond this point or damage of sensor could result. Also, when installing new thermal sensor, you must use a new locking ferrule in screw nut. Do not overtighten screw nut. Snug screw nut up and tighten 1/4 turn past this point.

The high temperature limit control is a manual reset control which senses the temperature of the shortening. If the shortening temperature exceeds the safe operating limit, this control will open and shut off the heat to the frypot.

The high limit light will then illuminate and control must manually be reset.

Disconnect the two wires from the high limit temperature control. Check for continuity between the two terminals after resetting the control. If the circuit is open, replace the control following these procedures. If the circuit is closed, the high limit is not defective. Reconnect the two electrical wires.

1091

2-3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Control Panel IntroductionTest Instruments RemovingThermal Sensor Removing the Control PanelThermal Sensor High Temperature Limit ControlHigh Temperature High Temperature Limit ControlHeating Elements Heating Elements ReplacementContactors Test Points Results Heat ContactorTest Points Results Primary Contactor FAN Place ON/OFF switch to the OFF position and unplugPower cord to open the wall circuit breaker Test Points ResultsCheckout Replacement COOK/PUMP SwitchFuses Drain SwitchFilter Heater Switch Filter Heater To age and deteriorate. The hose and fittings should be Shortening with temperature in excess of 200 of flowsHose assembly leaks or ruptures Through this filter rinse hose. Heat causes the rubber hoseFilter Pump Filter ValvePump, this mark must be together and face to the front When removing a pump from a motor note the positionsFryer. There is an indicator on the side of the two halves Motor in any other position could cause damage toCooling FAN ReplacementMaintenance Pumpand MotorFuse, or electrical shock could result Restore power to unit and unit is now ready for operationHenny Penny Model OE-100 994 1197 Henny Penny Model OE-100 Henny Penny Model OE-100 694 Henny Penny Model OE-100 1294

OE-100 specifications

The Henny Penny OE-100 is a premier commercial pressure fryer that stands out in the fast-food and restaurant industries for its efficiency, versatility, and superior frying capabilities. Designed to enhance the cooking process, the OE-100 brings innovation and reliability to kitchens, making it an essential tool for operators looking to serve high-quality fried foods consistently.

One of the key features of the Henny Penny OE-100 is its advanced frying technology. The pressure frying system allows for faster cooking times while sealing in moisture and flavor. This technology not only produces crispy, golden-brown fried products but also helps to reduce the amount of oil absorption, leading to healthier meal options. The pressure cooking process shortens the cooking time by using pressurized steam, which raises the boiling point of water. This means foods can be cooked quickly without compromising texture or taste.

Another notable characteristic of the OE-100 is its energy efficiency. The fryer is designed to use less oil, making it environmentally friendly and cost-effective. Additionally, the machine incorporates insulation that minimizes heat loss, which optimizes energy consumption. This is particularly beneficial for high-volume operations where reducing operational costs is crucial.

The OE-100 also features user-friendly controls, making it easy for operators to set precise cooking times and temperatures. This precision promotes consistency in food quality, ensuring that every batch of fried products meets a restaurant's high standards. Safety is another priority in the design of the OE-100, which includes features such as a built-in safety valve, automatic lid locking mechanisms, and cool-to-the-touch exteriors to minimize the risk of burns which are common in commercial frying operations.

Furthermore, the Henny Penny OE-100 is made with durable materials, ensuring longevity in rugged kitchen environments. Its compact design allows it to fit into various kitchen layouts, while still providing ample frying capacity.

Overall, the Henny Penny OE-100 stands as a benchmark in pressure frying technology, combining advanced features, energy efficiency, and safety to deliver exceptional results in commercial kitchens. Its ability to produce delicious, high-quality fried foods makes it a favorite among culinary professionals.
Top Page Image Contents