Panasonic KX-TDE100 Manual: Installation & Setup Guide

2.1.1 Installing and Starting the Maintenance Console

*1

*2

*3

*4

When not using a DHCP server to obtain a DNS server IP address automatically:

a.Select Manual for the DNS Server Address Method setting.

b.In the Manual Preferred DNS Server IP Address box, type the IP address of the preferred DNS server.

c.In the Manual Alternate DNS Server IP Address box, type the IP address of the alternate DNS server.

d.Click Apply.

The system menu appears. You may now begin programming the PBX.

Notice

•Do not change the IP addresses of the IPCMPR/IPCEMPR and DSP cards once IP telephones are registered to the PBX using these IP addresses.

The IP telephones will not operate properly if these IP addresses are changed.

•A DHCP server must be able to use a "client identifier" option specified by RFC 2131.

•The PBX will not start properly if the IP addresses cannot be assigned automatically by the DHCP server when DHCP Client is set to Enable. In this case, you need to consult your network administrator because the DHCP server on your network may not be running or a network failure may have occurred. If the DHCP server cannot be available, change the DHCP Client setting to Disable and set fixed IP addresses, then restart the PBX.

To change the DHCP Client setting, connect the PC with an RS-232C cross cable or Ethernet straight cable. When connecting the PC with an Ethernet straight cable, make sure the PBX is disconnected from the LAN and then connect the PC with an Ethernet straight cable using 192.168.0.101 for the IP address of the IPCMPR/IPCEMPR card.

Valid IP address range: "1.0.0.0" to "223.255.255.255"

Valid IP address range: "1.0.0.0" to "223.255.255.255"

Valid subnet mask address range: "0–255.0–255.0–255.0–255" (except 0.0.0.0 and 255.255.255.255)

Valid IP address range: "1.0.0.0" to "223.255.255.255"

Programming Manual for Virtual SIP Trunk Card

15

Image 15

Panasonic KX-TDE100 manual Installing and Starting the Maintenance Console

Contents

Pure IP-PBX Programming Manual for Virtual SIP Trunk Card Table of Contents Section Overview Information about IP Telephony Service Requirements for Internet Telephony ServiceSIPGW16 Connection Outline Information about IP Telephony Service WAN Required Ports for Each Channel Important Notice for Subscription and InstallationPort Requirements Firewall Requirements Bandwidth Requirements Router RequirementsRequired Bandwidth for Each Channel Items Specification Specifications Specifications Preparations for PC Programming Installing and Starting the Maintenance Console Maintenance Console Operating Instructions Installing the Maintenance Console When country/area data do not match Installing and Starting the Maintenance Console Under Configuration, click Slot Installing the V-SIPGW16 Card to the PBX Programming the V-SIPGW16 Card Accessing Port Properties Programming the V-SIPGW16 Card-Port PropertyProgramming Port Property Main Account Authentication ID Authentication PasswordUser Name Register Register AbilityRegister Sending Interval Registrar Server-IP Address Un-Register Ability when port INS4 NAT Registrar Server-Name Stun Server Port Number OptionStun Server-Name Stun Server-IP Address Proxy-Require Option Session Refresh Session Timer-Session Timer AbilitySession Refresh Session Timer-Session Expire Timer Session Refresh Session Timer-Refresh Method Calling Party Header TypeFrom Header-User Part Called Party Type Voice/FAX IP Codec Priority-1st, 2nd, 3rd Packet Sampling Time G.711APacket Sampling Time G.711µ Maximum Bit Rate Packet Sampling Time G.729AVoice Activity Detection for G.711 FAX Sending Method 9 RTP/RTCP RTP QoS AbilityRTP QoS-ToS Priority 10 T.38 FAX Udptl Redundancy count for data FAX Udptl Error Correction RedundancyFAX Max Datagram FAX Udptl Redundancy count for T.30 messages FAX QoS-ToS Priority 11 T.38 OptionFAX Rate Management Method FAX QoS Available FAX QoS-HEX 12 DSPFAX QoS-ToS Type FAX QoS-DSCP Supplementary Service Cnip Receive Cnip Send Value Range Programming Card Property Accessing Card PropertiesProgramming the V-SIPGW16 Card-Card Property Card Property Manual DNS Server Port Number DNS Retry Interval TimerManual Preferred DNS Server IP Address Manual Alternate DNS Server IP Address DNS SRV Record Resolve Ability SIP Client Port Number Accessing Shelf PropertiesProgramming the V-SIPGW16 Card-Shelf Property Programming Shelf Property NAT Keep Alive Packet Sending Interval NAT Voice RTP UDP Port NoNAT Keep Alive Packet Sending Ability NAT Keep Alive Packet Type Symmetric Response Routing Ability Stun External Address Detection Retry CounterStun Resending Interval SIP Called Party Number Check Ability SIP T1 Timer Timer Section Maintenance To export provider profiles Configuration ManagementImporting/Exporting V-SIPGW16 Provider Profiles To import provider profiles SIPGW16 Protocol Trace To save trace data to the SD Memory CardTo transfer trace data to the PC SIPGW16 Protocol Trace Index Index Programming Manual for Virtual SIP Trunk Card PSQX5028ZA KK1008TE0