Hoshizaki JWE-620UA-6B service manual Error Codes, Ready Lamp, Auto Fill Lamp, Mode Lamps

Page 23
"ON/OFF" Button
board uses an LED display to show system details and diagnostic
Down Button
Display
"MODE" Button
"STANDBY/ CLEANING" Button
Up Button

4. Operation Panel Layout

The operation panel is mounted on the side of the unit and is connected to the CN5 connector on the control board.

"READY" Lamp

"AUTO FILL" Lamp

Mode Lamps

"STANDBY/ CLEANING" Lamp

5. Features

a) Display This operation information.

b) Service Menu and Error Log

A service menu [“01” to “17” and “21” to “25” (Auxiliary Code U-1, U-2, U-3, V-0, A-0) or "01" to "23" and "26" to "30" (Auxiliary Code A-1 and later)] allows for viewing and setting of system operating details and parameters. See "II.D.7. Service Menu and Error Log."

c) Error Codes

Error codes ("A1" to "A3," "H1" to "H7," "o1," "o2") are designed to protect the unit. These codes give information or warnings in the event the unit is operating out of acceptable parameters. See "III.B. Error Codes."

6. Controls, Adjustments, and Lamps

a) "READY" Lamp

Comes on when the auto fill cycle completes and the dishwasher is ready to wash.

b) "AUTO FILL" Lamp

Flashes during the auto fill cycle, and goes off at the end of the cycle.

c) Mode Lamps

Comes on to indicate the selected operation mode, and flash during operation.

18

Image 23
Contents Model JWE-620UA-6B Hoshizaki AMERICA, INC Contents Page Important Safety Information Display Specifications Specification SheetNameplate Rating Dimensions/Connections Dishwasher II. General Information A. ConstructionInternal Booster Tank Auxiliary Code U-1, U-2, U-3, V-0, A-0 Control BoxAuxiliary Code A-1 and Later Auto Fill lamp flashing and RINSE, STANDARD, or Long lamp on Sequence of OperationAuto Fill Cycle Wash Cycle Rinse Cycle STANDBY/CLEANING Button StartDrain Rinse lamp flashingSequence of Operation Flow Chart Auxiliary Code A-1 and Later Control Board Location Control Board and Operation BoardCN5 Control Board LayoutCN9 Control Board DiagramX10 Auto Fill Lamp Error CodesMode Lamps Ready LampStandby Lamp Mode ButtonSTANDBY/CLEANING Button Service Menu AccessDefault Service Menu Chart Auxiliary Code U-1, U-2, U-3, V-0, A-0Service Menu Chart Auxiliary Code A-1 and Later Temperature Display Special Modes Error CodesInternal Booster Tank Energy Saving Mode BuzzerAlert Function Auxiliary Code A-1 and Later Continuous Wash ModeConsecutive Rinse Mode OFF Switch Open/Closed Display Mode III. Service DiagnosisDiagnostic Procedure Page Error Code Table Error CodesError Code Log Auto Fill Error A1 Error Code DetailsInternal Booster Tank Auto Fill Error A2 Wash Tank Water Level Error A3 Defective Replace Control Board Repair or replace Replace Wash Tank Thermistor Error H1, H2 Internal Booster Tank Thermistor Error H3, H4 Eeprom Error H6 ROM/RAM Error H5Phase Reversal Error H7 Unit Will Not Start Service Flow ChartsPage Dishes Not Clean Page Inadequate Rinse Dishwasher Will Not Start When Door Closed Wash Tank Water Boils No or Inadequate Detergent/Rinse Aid SupplyWash Tank Water Not Draining Float Switch Cleaning Float Switch Check and CleaningFloat Switch Check Thermistor Check Removal of Panels IV. Removal and Replacement of ComponentsAccessing the Control Box Page Removal and Replacement of Internal Booster Tank Removal and Replacement of Wash Pump Motor Removal and Replacement of Rinse Pump Motor Removal and Replacement of Handle Removal and Replacement of Door Removal and Replacement of Spring Removal and Replacement of Spring UnitAdjustment of Door Opening/Closing Force Removal and Replacement of Flush Pipe Packing Installation Instructions Removal and Replacement of Thermistor Operation Board Removal and Replacement of Control Board or Operation BoardControl Board Page Cleaning and Maintenance Instructions Daily Maintenance Pump Filter Water Level Sensor Location Front Self-Cleaning Monthly Inspection Weekly MaintenanceDescaling As Required Shutdown Long Storage, Relocation, Disposal, Transfer VI. Operating Instructions VII. Technical Information Water Circuit Auxiliary Code U-1, U-2, U-3, V-0, A-0 Wiring DiagramAuxiliary Code A-1 and Later