Hoshizaki DCM-500BAH-OS, DCM-500BWH-OS Dispensing Components DCM-500BAH, DCM-500BWH

Page 19

3.60 seconds after the "GM" LED comes on, the "COMP" LED comes on, and the compressor and fan motor start. If the "COMP" LED does not come on 60 seconds after the gear motor starts, check that the gear motor protect relay contacts (connector K2 terminals 1 and 2) have closed. If the "COMP" LED is on and the compressor and fan motor did not start, check for 115/120V at X2 (LBU) and X2 (BR) on the control board to neutral. If the "COMP" LED is on and there is voltage at X2 (BR) to neutral and no voltage at X2 (LBU) to neutral, the control board is bad and should be replaced. See wiring diagram "III.C.3. Freeze Cycle" for further details.

c)Dispensing Components DCM-500BAH, DCM-500BWH

1.Ice Dispense "Continuous": Pressing the ice dispense switch closes terminals 6 and 5 at the K4 connector. The "DM" LED comes on and the dispensing motor energizes. If the "DM" LED does not turn on, check continuity through the ice dispense switch and the dispense mode switch. If the LED is on and the dispensing motor does not start, check for 115/120V at connector K2 terminals 3 and 6 to a neutral. With voltage at terminal 3 and not at terminal 6, the control board is bad and should be replaced. Note: The agitating motor will operate .6 seconds every 12 seconds of accumulative

dispense time. See "III.D.1. Continuous Dispense."

2.Ice Dispense "Portion": Pressing the ice dispense switch closes terminals 6 and 7 at the K4 connector. The "DM" LED comes on and the dispinsing motor energizes. If the "DM" LED does not turn on, check continuity through the ice dispense switch and the dispense mode switch. If the LED is on and the dispensing motor does not start, check for 115V at connector K2 terminals 3 and 6 to a neutral. With voltage at terminal 3 and not at terminal 6, the control board is bad and should be replaced.

Note: The agitating motor will operate .6 seconds every 12 seconds of accumulative dispense time. See "III.D.2. Portion Dipsense."

d)Dispensing Components DCM-500BAH-OS,DCM-500BWH-OSSee "IV.C.5. Opti Serve (OS) Sensors."

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents DCM-500BAH DCM-500BAH-OS DCM-500BWH DCM-500BWH-OS Hoshizaki AMERICA, INC Contents Page DCM-500BAH Specifications IcemakerWater TEMP. F DCM-500BAH-OSWater TEMP. F DCM-500BWHPotable Water Water Cooled Condenser DCM-500BWH-OSII. General Information Construction Spout a Expansion Valve Spout B Evaporator Assembly DCM-500BAH-OS, DCM-500BWH-OS Ice Making UnitSequence of Operation Startup Control Board Control Board Control Board Layout DCM-500BAH, DCM-500BWHPart Number 2A2649-01 LED Lights FeaturesIce Making Components Controls and Adjustments Portion ControlControl Board Check Procedure Power SupplyDispensing Components DCM-500BAH, DCM-500BWH Float Switch DCM-500BAH-OS Inlet Water Valve Water Supply Wire Color Code Wiring DiagramsDCM-500BAH-OS, DCM-500BWH-OS DCM-500BWH-OS Sequence of Electrical Circuit Ice MakingDCM-500BWH-OS Ice Purge CycleFreeze Cycle Hour Drain Cycle / Drain Switch Shutdown Low Water Safety High Pressure Switch Continuous Dispense Sequence of Electrical Circuit DispensingPortion Dispense ICE Production Performance DataTotal IV. Service Diagnosis Diagnostic Procedure Ice Production Check No Ice Production Diagnostic ChartsProblem Possible Cause Remedy Problem Possible Cause Remedy Low Ice Production Other Dispensing Opti Serve OS Sensors 5b. Ice Dispensing Portion Mode 5a. Ice Dispensing Continuous Mode5c. Water Dispensing Brazing Removal and Replacement of ComponentsService for Refrigerant Lines Refrigerant RecoveryEvacuation and Recharge R-404A Removal and Replacement of Compressor Removal and Replacement of Expansion Valve Removal and Replacement of Evaporator Assembly Components Upper Bearing Wear Check Removal and Replacement of Extruding HeadRemoval and Replacement of Evaporator Removal and Replacement of AugerPage 5b. Lower Housing Removal and Replacement of Gear Motor Page Removal and Replacement of Water-Cooled Condenser Page Removal and Replacement of Fan Motor Adjustment of Water Regulating Valve Water-Cooled Model OnlyRemoval and Replacement of Drain Valve Removal and Replacement of Inlet or Dispensing Water ValveDispensing Auger and Agitator Removal and Replacement of Dispensing SystemDispensing or Agitating Motor Page Cleaning and Sanitizing Instructions VI. Cleaning and MaintenanceWater System Cleaning ProcedureDispensing Components Sanitizing SolutionBin Control Bracket Snap Pin Frequency Area Task MaintenancePreparing the Icemaker for Long Storage
Related manuals
Manual 46 pages 41.9 Kb Manual 69 pages 57.62 Kb

DCM-500BWH, DCM-500BAH, DCM-500BWH-OS, DCM-500BAH-OS specifications

The Hoshizaki DCM-500BWH-OS, DCM-500BWH, DCM-500BAH, and DCM-500BAH-OS are advanced ice makers designed to meet the needs of busy commercial environments. Hoshizaki is a renowned manufacturer known for producing high-quality refrigeration and foodservice equipment, and their DCM series of ice makers exemplifies this commitment to excellence.

One of the main features of the DCM-500 series is its ability to produce a significant amount of ice, ideally suited for restaurants, bars, and hotels. With a production capacity of up to 500 pounds of nugget ice per day, these units provide an efficient solution for establishments that require a steady supply of ice.

The nugget ice produced by the DCM-500 series is not only soft and chewable but also retains the cold temperature longer, making it perfect for beverages. This appealing characteristic of nugget ice caters to growing customer preferences for premium ice options.

These models also incorporate advanced ice-making technology, ensuring consistent quality. The DCM-500BWH-OS and DCM-500BAH-OS variants feature a self-contained design that makes installation simple and efficient, providing enhanced portability that makes them versatile for different locations within a commercial space.

The DCM-500BWH and DCM-500BAH models are equipped with features like a built-in ice bin that allows for storage convenience. The ice bins have a substantial holding capacity, reducing the frequency of refills and improving overall operation efficiency.

Additionally, the DCM-500 series is designed with energy efficiency in mind. Integrated with modern refrigeration systems, these ice makers comply with energy-saving standards, helping to reduce operational costs. User-friendly controls allow for easy adjustment and monitoring, ensuring that operators can manage their ice production without hassle.

Moreover, the robust construction materials used in these models increase durability, making them suitable for high-demand environments. Features such as easy-to-clean surfaces and self-diagnostic systems further optimize maintenance, ensuring prolonged performance without significant downtime.

Overall, the Hoshizaki DCM-500BWH-OS, DCM-500BWH, DCM-500BAH, and DCM-500BAH-OS ice makers are excellent choices for businesses seeking reliable and high-capacity ice production. Their advanced features, energy efficiency, and user-friendly operation make them a valuable addition to any commercial kitchen or bar setup.
Top Page Image Contents