Hoshizaki DCM-500BAH-OS, DCM-500BWH-OS service manual Removal and Replacement of Gear Motor

Page 55

18)Move the power switch to the "ON" position, then replace the panels in their correct positions.

19)Turn on the power supply, then move the control switch to the "ICE" position to start the automatic icemaking process.

6.Removal and Replacement of Gear Motor

1)Move the control switch to the "DRAIN" position and drain all of the water from the evaporator.

2)After the water has stopped draining, move the control switch to the "OFF" position, then turn off the power supply. Remove the front and top panels, then move the power switch to the "OFF" position.

3)Remove the front cover of the storage bin. Remove spout B, then remove spout A. See Fig. 1.

4)Remove the apron panel, then remove the left side panel.

5)Remove the evaporator bracket.

6)Remove the bolts securing the lower housing to the gear motor. Lift the evaporator up slightly.

7) Remove the gear motor/drain pan bolts. See Fig. 3.

8)Disconnect the wiring from the gear motor, then remove the gear motor from the drain pan.

9)Remove the gear motor bracket from the old gear motor and attach to the new gear motor.

10)Remove the spline coupling and gear motor cover from the old gear motor and attach to the new gear motor. The narrow side of the gear motor cover should be towards the evaporator. After tightening the mounting screws, apply silicone caulk to the heads to seal them.

11)Place the new gear motor in the drain pan.

12)Using the gear motor/drain pan bolts and washers, secure the gear motor and drain pan to the drain pan bracket.

13)Connect the gear motor wires.

14)Lower the evaporator down and secure it to the gear motor.

15)Replace the evaporator bracket in its

correct position.

Gear Motor

Cover Screws

Gear Motor Cover

Gear Motor

Gear Motor/Drain Pan

Bolts and Washers

Gear Motor Bracket

Gear Motor

Bracket Bolts

Drain Pan

Drain Pan

Bracket Bolts

Drain Pan Bracket

16) Replace spout A, spout B, and the front

 

cover of the storage bin in their correct

Fig. 3

positions.

55

Page 54 Page 56
Image 55
Page 54 Page 56
Contents DCM-500BAH DCM-500BAH-OS DCM-500BWH DCM-500BWH-OS Hoshizaki AMERICA, INC Contents Page DCM-500BAH Specifications IcemakerWater TEMP. F DCM-500BAH-OSWater TEMP. F DCM-500BWHPotable Water Water Cooled Condenser DCM-500BWH-OSII. General Information Construction Spout a Expansion Valve Spout B Evaporator Assembly DCM-500BAH-OS, DCM-500BWH-OS Ice Making UnitSequence of Operation Startup Control Board Control Board Control Board Layout DCM-500BAH, DCM-500BWHPart Number 2A2649-01 LED Lights FeaturesIce Making Components Controls and Adjustments Portion ControlControl Board Check Procedure Power SupplyDispensing Components DCM-500BAH, DCM-500BWH Float Switch DCM-500BAH-OS Inlet Water Valve Water Supply Wire Color Code Wiring DiagramsDCM-500BAH-OS, DCM-500BWH-OS DCM-500BWH-OS Sequence of Electrical Circuit Ice MakingDCM-500BWH-OS Ice Purge CycleFreeze Cycle Hour Drain Cycle / Drain Switch Shutdown Low Water Safety High Pressure Switch Continuous Dispense Sequence of Electrical Circuit DispensingPortion Dispense ICE Production Performance DataTotal IV. Service Diagnosis Diagnostic Procedure Ice Production Check No Ice Production Diagnostic ChartsProblem Possible Cause Remedy Problem Possible Cause Remedy Low Ice Production Other Dispensing Opti Serve OS Sensors 5b. Ice Dispensing Portion Mode 5a. Ice Dispensing Continuous Mode5c. Water Dispensing Brazing Removal and Replacement of ComponentsService for Refrigerant Lines Refrigerant RecoveryEvacuation and Recharge R-404A Removal and Replacement of Compressor Removal and Replacement of Expansion Valve Removal and Replacement of Evaporator Assembly Components Upper Bearing Wear Check Removal and Replacement of Extruding HeadRemoval and Replacement of Evaporator Removal and Replacement of AugerPage 5b. Lower Housing Removal and Replacement of Gear Motor Page Removal and Replacement of Water-Cooled Condenser Page Removal and Replacement of Fan Motor Adjustment of Water Regulating Valve Water-Cooled Model OnlyRemoval and Replacement of Drain Valve Removal and Replacement of Inlet or Dispensing Water ValveDispensing Auger and Agitator Removal and Replacement of Dispensing SystemDispensing or Agitating Motor Page Cleaning and Sanitizing Instructions VI. Cleaning and MaintenanceWater System Cleaning ProcedureDispensing Components Sanitizing SolutionBin Control Bracket Snap Pin Frequency Area Task MaintenancePreparing the Icemaker for Long Storage
Related manuals
Manual 46 pages 41.9 Kb Manual 69 pages 57.62 Kb

DCM-500BWH, DCM-500BAH, DCM-500BWH-OS, DCM-500BAH-OS specifications

The Hoshizaki DCM-500BWH-OS, DCM-500BWH, DCM-500BAH, and DCM-500BAH-OS are advanced ice makers designed to meet the needs of busy commercial environments. Hoshizaki is a renowned manufacturer known for producing high-quality refrigeration and foodservice equipment, and their DCM series of ice makers exemplifies this commitment to excellence.

One of the main features of the DCM-500 series is its ability to produce a significant amount of ice, ideally suited for restaurants, bars, and hotels. With a production capacity of up to 500 pounds of nugget ice per day, these units provide an efficient solution for establishments that require a steady supply of ice.

The nugget ice produced by the DCM-500 series is not only soft and chewable but also retains the cold temperature longer, making it perfect for beverages. This appealing characteristic of nugget ice caters to growing customer preferences for premium ice options.

These models also incorporate advanced ice-making technology, ensuring consistent quality. The DCM-500BWH-OS and DCM-500BAH-OS variants feature a self-contained design that makes installation simple and efficient, providing enhanced portability that makes them versatile for different locations within a commercial space.

The DCM-500BWH and DCM-500BAH models are equipped with features like a built-in ice bin that allows for storage convenience. The ice bins have a substantial holding capacity, reducing the frequency of refills and improving overall operation efficiency.

Additionally, the DCM-500 series is designed with energy efficiency in mind. Integrated with modern refrigeration systems, these ice makers comply with energy-saving standards, helping to reduce operational costs. User-friendly controls allow for easy adjustment and monitoring, ensuring that operators can manage their ice production without hassle.

Moreover, the robust construction materials used in these models increase durability, making them suitable for high-demand environments. Features such as easy-to-clean surfaces and self-diagnostic systems further optimize maintenance, ensuring prolonged performance without significant downtime.

Overall, the Hoshizaki DCM-500BWH-OS, DCM-500BWH, DCM-500BAH, and DCM-500BAH-OS ice makers are excellent choices for businesses seeking reliable and high-capacity ice production. Their advanced features, energy efficiency, and user-friendly operation make them a valuable addition to any commercial kitchen or bar setup.
Top Page Image Contents