Hoshizaki KM2000SWF3, KM-2000SRH3, KM-2000SRF3, KM-2000SWH3 service manual

Page 12

2)Defrost Timer

The defrost cycle starts when the Float Switch opens and completes the freeze cycle. But the Defrost Timer does not start counting until the Thermistor senses 48°F at the Evapora- tor outlet. The period from the end of the freeze cycle up to the point of the Thermistor's sensing varies depending on the ambient and water temperatures.

3)High Temperature Safety - 127 ± 7°F

The temperature of the suction line in the refrigerant circuit is limited by the High Tempera- ture Safety.

During the defrost cycle the Evaporator temperature rises. The Thermistor senses 48°F and starts the Defrost Timer. After the Defrost Timer counts down to zero, the normal freeze cycle begins. If the Evaporator temperature continues to rise, the Thermistor will sense the rise in temperature and at 127 ± 7°F the Thermistor operates the High Tempera- ture Safety.

This High Temperature Safety shuts down the circuit and the icemaker automatically stops. To reset the safety, turn the power off and back on again.

This High Temperature Safety protects the unit from excessive temperature. The Control Board will Beep every 3 seconds. The white Reset Button on the Control Board must be pressed with power on to reset the Safety.

4)Low Water Safety

If the Pump Motor is operated without water, the mechanical seal can fail. To prevent this type of failure, the Controller Board checks the position of the Float Switch at the end of the initial one minute water fill cycle and at the end of each defrost cycle.

If the Float Switch is in the up position (electrical circuit closed), the Controller Board changes to the ice making cycle. If the Float Switch is in the down position (electrical circuit open), the Controller Board changes to a one minute water fill cycle before starting the ice making cycle. This method allows for a Low Water Safety shut down to protect the Water Pump from mechanical seal failure.

For water-cooled model, if the water is shut off, the unit is protected by the High Pressure Switch.

5)High Voltage Cut-out

The maximum allowable supply voltage of this icemaker is limited by the High Voltage Cut-out.

If miswiring (especially on single phase 3 wire models) causes excessive voltage on the Controller Board, the High Voltage Cut-out shuts down the circuit in 3 seconds and the icemaker automatically stops. When the proper supply voltage is resumed, the icemaker automatically starts running again. The Control Board will signal this problem using 7 Beeps every 3 seconds.

6)LED Lights and Audible Alarm Safeties

The red LED indicates proper control voltage and will remain on unless a control voltage

12

Image 12
Contents Model KM-2000SWF3 KM-2000SRF3 KM-2000SWH3 KM-2000SRH3 Hoshizaki AMERICA, INC Contents Maintenance Specifications KM-2000SWF3, KM-2000SWH3 Water-cooledKM-2000SRF3, KM-2000SRH3 Remote air-cooled Condensing Unit Specifications Model URC-20F II. General Information Construction KM-2000SWF3, KM-2000SWH3KM-2000SRF3, KM-2000SRH3 Features of Control Products E Controller Board Controller BoardSOLID-STATE Control Controller BoardPage Beep every 3 sec. = High Evaporator Temperature 127 F Minute Fill CycleHarvest Cycle Freeze CycleControl Products HOSHIZAKI001 Board Control Products HOS-001A Board Page Important Water Valve opening is limited to 6 minutes Important Water Valve opening is limited to 6 minutes Controls and Adjustments Setting Time Setting Frequency Checking the Controller Board Page III. Technical Information KM-2000SRF3, KM-2000SRH3 Wiring Diagrams Timing Chart Page Performance Data KM-2000SRF3, KM-2000SRH3 IV. Service Diagnosis No ICE Production Problem Possible Cause RemedyController Board Problem Possible Cause Remedy Evaporator is Frozen UP ThermistorLOW ICE Production Abnormal ICEOthers Removal and Replacement of Components Service for Refrigerant LinesRefrigerant Recovery Evacuation and Recharge R-404ABrazing Removal and Replacement of Compressor Important Removal and Replacement of Drier Removal and Replacement of Expansion Valve Removal and Replacement of HOT GAS Valve and Line Valve Removal and Replacement of Evaporator Important Page Adjustment of Water Regulating Valve WATER-COOLED Model only Page Removal and Replacement of Thermistor Caution Removal and Replacement of FAN Motor Removal and Replacement of Water Valve Removal and Replacement of Pump MotorRemoval and Replacement of Spray Tubes Page Page Cleaning Procedure Cleaning Procedure Page Sanitizing Procedure Following Cleaning Procedure Maintenance
Related manuals
Manual 29 pages 20 Kb

KM-2000SWH3, KM-2000SRF3, KM-2000SRH3, KM2000SWF3 specifications

The Hoshizaki KM-2000SRH3 and KM-2000SWH3 are two of the latest innovations in the world of ice-making machines, designed for high-demand commercial settings where reliability and efficiency are key. Known for their durability and performance, these machines are ideal for restaurants, bars, hotels, and other businesses that require a steady supply of ice.

One of the standout features of the KM-2000 series is its production capability. Both models are designed to produce a staggering amount of ice—approximately 2,000 pounds per day. This high output ensures that establishments are never left wanting, meeting the needs of peak service hours without interruption.

Hoshizaki has integrated advanced technologies into these machines to enhance efficiency and reduce downtime. The KM-2000SRH3 and KM-2000SWH3 come equipped with a reliable, self-contained refrigerant system that operates efficiently even in warmer environments. This is particularly important for businesses located in hotter climates, as it ensures that ice production remains consistent throughout the year.

Another notable technology included in both models is the unique crescent-shaped ice that they produce. This type of ice is not only aesthetically pleasing but also offers several functional advantages. The crescent shape allows for excellent cooling properties, making it perfect for drinks, while its hardness and density facilitate longer melting times, ensuring that beverages stay chilled for longer periods.

Additionally, Hoshizaki has incorporated a cleaning and sanitizing system in the KM-2000 series, ensuring that the ice produced is safe and hygienic. This built-in feature is crucial for maintaining health and safety standards in food service operations, reducing the need for manual cleaning and increasing operational efficiency.

In terms of design, both the KM-2000SRH3 and KM-2000SWH3 boast a compact footprint, making them suitable for spaces where size is a constraint. Their stainless steel construction not only adds to their durability but also enhances their visual appeal, fitting seamlessly into any commercial kitchen or bar environment.

Overall, the Hoshizaki KM-2000SRH3 and KM-2000SWH3 ice machines represent a convergence of efficiency, technology, and user-friendly design, making them a top choice for businesses that rely heavily on ice as a part of their service offerings. With their high production capabilities, advanced features, and commitment to quality, these models deliver reliable performance that operators can depend on day in and day out.