InSinkErator HC3/GN3, H770 owner manual Troubleshooting

Page 14

Please read Troubleshooting Guide and/or visit

www.insinkerator.com before calling AnswerLine

TROUBLESHOOTING

PROBLEM

POSSIBLE CAUSE

WHAT TO DO

Water and steam spits

• Unit is boiling.

• Activate faucet lever to release some water from

forcefully from spout

May be normal during initial setup.

the tank.

without turning on the

• Adjust water temperature using dial on tank front.

 

dispenser faucet.

 

 

Remember that at higher altitudes, water boils

 

 

 

 

at lower temperatures.

 

 

 

Water is not hot.

• The unit is unplugged.

• Make sure the unit is connected to a properly grounded

 

• The electric outlet is inoperative.

electric outlet.

 

• Make sure the circuit breaker or fuses are

 

 

 

 

functioning properly.

 

 

• Check that the outlet is not switched off.

 

 

 

Water is too hot

• Thermostat is not adjusted to

• Adjust the thermostat slowly, then activate faucet lever for 20

or not hot enough.

your needs.

seconds to bring in fresh water to be heated at the new setting.

 

 

Allow 5-7 minutes for water to reach new temperature.

 

 

 

Water comes out the

• Outlet tube is blocked.

• Check that outlet tube is not kinked, twisted or pinched.

vent instead of spout.

 

• Unscrew spout end piece and clean out any debris.

 

 

 

 

 

Water is dripping from

• The expansion chamber isn’t

• Unplug the unit. If the dripping doesn’t stop after a few

the spout/vent

draining properly due to low

minutes, check the supply valve to ensure that is fully

intermittently.

water pressure.

open and there are no obstructions in the water line

 

• The spout is blocked.

reducing the pressure below 30 psi (i.e., a poorly mounted

 

saddle valve, a clogged water filter, or a partially opened

 

 

 

 

shut-off valve).

 

 

• Unscrew spout end piece and clean out any debris.

 

 

 

Water is dripping

• Debris in the water line may be

• Unscrew spout end piece and clean out any debris.

from the spout/vent

in the faucet valve seat causing a

• Activate faucet lever 7-10 times to flush faucet & lines.

constantly.

slow water leak.

 

 

 

 

Divided stream.

• Debris in the end piece.

• Unscrew spout end piece and clean out any debris.

 

 

 

Water continues to run

• Mounting nut too tight.

• Loosen mounting nut, 1/4 turn at a time, until shut-off occurs.

after releasing lever.

• Mounting washers not

• See page 6 or 7, Step 2B to check proper mounting

(HC3/GN3/View/ Wave)

installed properly

washer installation.

 

 

 

 

If you are still experiencing trouble call the AnswerLine1-800-558-5700.

14

Image 14
Contents Instant Hot Water Dispenser What YOU should Know Before YOU Begin What YOU Need to GET StartedH770-SS HC-View-SS H-View-SS HC-Wave-SS H-Wave-SS HC3-SSH990-SS Components in this Package Appropriate tools PreparationIf you have to drill through sink or View/Wave Installing the Faucet VIEW/ WaveView/Wave For a standard 11⁄2 sink/counter hole Hot & Cool models onlyHC3 only Installing the Faucet HC3/ GN3HC3/ GN3 An assistant may be needed to hold Installing the Faucet H990Make sure to use rubber gasket To ensure proper seal H990 Should cradle all descending tubes Installing the Faucet H770Make sure to use fiber gasket To ensure proper seal H770 Leave 1/4 for hanging tank Connecting Faucet to TankMounting the Tank Hose clamps are not needed for anyHC-View / HC-Wave / HC3 Fill Tank & then Connect PowerFinal Water Connection View / H-Wave / GN3 / H990 / H770Warranty Information Year warrantyFactory temperature pre-set Care and USETroubleshooting Manual del usuario Tarugos para panel de yeso Broca corta-círculos PunzónCómo Usar Este Manual DE Instrucciones Contenido DE Este Paquete ⁄4 2 cm Preparación5 cm Wave-SSPara un orificio estándar de 11⁄2 de fregaderos o gabinetes Instalación DEL Grifo VIEW/ WaveÚnicamente en los modelos caliente y frío El grifo sale de fábrica listo para suHC3 unicamente Instalación DEL Grifo HC3/GN3HC3 / GN3 Para obtener un sellado correcto Instalación DEL Grifo H990Desempaque los componentes del Daños materiales No apriete ni rompa el tuboPuede ser necesario un ayudante para Instalación DEL Grifo H770Para obtener un sellado correcto H770 ArandelaDrenarlo si es necesario Montaje DEL TanqueConexión DEL Grifo EN EL Tanque View / H-Wave / GN3/ H990 / H770 Conexión Final DEL AguaLlene EL Tanque Y Enseguida Enchúfelo El agua saldrá fría en un principioInformación Sobre LA Garantía Años de garantía7 minutos para que el agua alcance la nueva temperatura Mantenimiento Y USOAjuste el termostato Identificación Y Solución DE Problemas En el númeroManuel du propriétaire CE QUE Vous Devriez Savoir Avant DE Commencer ’installation Ce que vous verrez dans le manuel d’instructionsDans CET Emballage Wave-SS21⁄2 Préparation21⁄4 13⁄4Pour un trou dévier/comptoir standard de 11⁄2 po 3.8 cm Installation DU Robinet VIEW/ WaveModèles chaud et froid seulemen En aurez besoin plus tard FigureDommage matériel Ne pincez pas ou Installation DU Robinet HC3/GN3HC3 seulement Installation DU Robinet H990 Installation DU Robinet H770 Montage DU Réservoir Connexion Finale DE L’EAU HC-View / HC-Wave / GN3 / H990 / H770Renseignements SUR LA Garantie Garantie de 3 ansSoins ET Utilisation La température à l’usine estDiagnostics 800.558.5700

H770, HC3/GN3 specifications

The InSinkErator HC3/GN3, H770 is a remarkable addition to any modern kitchen, emphasizing convenience, efficiency, and style. As part of InSinkErator's renowned line of hot water dispensers, this model is designed to deliver near-boiling water instantly, making kitchen tasks faster and more efficient.

One of the standout features of the HC3/GN3, H770 is its innovative heating technology. The system is equipped with a powerful heating element that brings water to a precise temperature of around 200 degrees Fahrenheit within seconds. This is perfect for a variety of culinary applications, whether you’re preparing tea, instant coffee, or soups. The almost immediate delivery of hot water eliminates the need for traditional kettles, allowing for more countertop space and reducing energy costs.

Another characteristic of this model is its sleek and compact design. The stylish faucet is available in several finishes, ensuring it can seamlessly blend into any kitchen aesthetic. The ergonomic handle enhances usability, providing ease in both filling pots and dispensing water for other cooking needs. The integrated design also minimizes clutter, combining the functionality of multiple appliances into one.

The HC3/GN3, H770 also prioritizes safety in its design. It features a child-resistant safety lock to prevent accidental activation, making it a safe choice for families with young children. Additionally, the tank is insulated to maintain hot water longer while keeping the surface cool to the touch, reducing the risk of burns.

In terms of installation, the InSinkErator HC3/GN3, H770 is relatively easy to set up under the sink, with a compact tank that fits snugly in kitchen cabinets. The user-friendly interface allows for adjustable temperature controls, enabling precise customization based on personal preferences.

Lastly, this model is built with durability in mind. The materials used are resistant to rust and corrosion, ensuring a long lifespan. InSinkErator also provides a warranty on its products, which underlines their commitment to quality and customer satisfaction.

In conclusion, the InSinkErator HC3/GN3, H770 is an essential kitchen accessory for those who value convenience, efficiency, and safety. Whether for everyday cooking needs or special occasions, this hot water dispenser serves to enhance the overall kitchen experience, epitomizing the blend of technology and practicality. With its robust features and thoughtful design, it is the perfect choice for any home.