Page 75
2. CONTINUE.
Cold Drink Center (327/328) Operator’s Guide
On input screen #2, you can press the following letters to perform the indicated operation:
ADispense ice (and turn on the icemaker compressor if the hop- per is not full)
BForce CO2 valve on
CDispense carbonated water
DDispense still water
5.Actuate each switch or sensor to test its function. As you actuate each input, the display element representing that switch blinks on. Releasing the switch causes that element to blink off again.
6.CONTINUE.
VIEW SUREVEND™ AVERAGE CALIBRATION VALUE
1. Press , then press until the display shows.
2. CONTINUE. | | CAL.AVEXXX |
| | |
3280020 | Page 69 | August, 2003 |
XXX represents the average sensor calibration value (should be between 50 and 255 for proper sensor operation - i.e. 51 through 254). Although this number could go as low as 20, the SureVend™ system will be inoperative in this condition.
VIEW SUREVEND™ LAST RECORDED CALIBRATION VALUE
1. Press , then press until the display shows.
XXX can be any number from 0 to 255, and represents theCALmost.LSTrecentXXX value read from the sensor. The lower the number, the greater the sensor
blockage. A number of 255 means that there is a fatal problem with the SureVend™ interface board. Ensure the SureVend™ interface PCB is properly connected to the main controller PCB.
Contents
Page
Crane Merchandising Systems Parts and Support
Table of Contents
Factory Default Throw Times and Volumes
View Diagnostic Messages
Page
Water Pressure
Power Requirements
Water Requirements
Country Volts Frequency Hz Current Amps
Positioning The Merchandiser
Final Installation
Supply Line Requirements
Flushing Water Supply Line
Load the coin
Mechanism Open the cab- inet door
MonetarySCREW door
Install Options
Everpure Water Filter Installation
Hydrolife Filter Installation
Load the cup mechanism
Get The Machine Ready To Vend Drinks
Bag-in-box machines
Syrup tank machines
Observe Proper Hygiene do not Touch the Cups
Set up the CO2 tank
Cold Drink Center 327/328 Operator’s Guide
Handle as shown. Once
Brix
Adjustments and Minor Maintenance
Refills
Press Water pump starts, and the display shows
Limit Screw see Warning Adjusting Screw
Priming Switch Adjusting Screw Lock
Set the Main Switch to the on up position Press Then
Getting Around
Programming The Cold Drink Center
Displays
Function Keys
Other Keys
Some Conventions
Helpful Hint
Control Panel Switch Functions Explained
Message if desired see Edit Custom Message on
SureVend
Or after being downloaded into a
Enter a NEW Supervisor Code
Gain Access to the Supervisor Mode
Supervisor Mode Only
Follow the steps in Gain Access To The Supervisor Mode on
Enter a NEW Data Recall Code
Usage
Examples Press
Consult your DEX supplier before choosing this option
SET Talker Mode
SET Printer or DEX Mode
To turn the talker option on or OFF
SET DEX Options
Printer mode only
Mechanism choice
Select Display Language
List of bills. See Initial Setup Of NonStandard Bill Valida
Select Bill Validator and Options
Tor on
Options on page 28 , to select
Initial Setup of Nonstandard Bill Validator
Select Monetary Options
Select Card Reader and Options
Some examples
Example If setting is
Example
SET UP Winner Mode
Selections. Press
SET UP MUG Discount
Disable Selections in the Merchandiser
This display means that all regular size selections a F are
This will reload the fac
SET UP CUP Sizes
Display momentarily shows
This will reassign
For the selection Pressing
SET UP a Drink
Appear View and change the settings for syrup
View and change the settings for ice throw time
Syrup Throw Still and Carb Ice Extra Ice
Factory Default Throw Times and Volumes
Cup Size Volume Time Sec
Special Selections
Press Until something like Displays. Press
Blended Drinks
Select
To use. For example, set percentage plus to This means
Press To select the type of pumps in your machine
Configure Pump Type
Spritz Drinks
Set
SET UP Automatic Delivery Door Options
Configure Number of Selections
Abcdef
Assign CUP Sizes to Selections Supervisor Mode Only
Optional or Mandatory Surevend
Turn Surevend on or OFF
Xxxxxx represents the current software version number
SET UP the Surevend ANTI-JACKPOT Timer
View Software Version
Receives change
SET the Time of DAY
SET MONTH, DATE, and Year
SET Daylight Savings Time Options
SET TIME-OF-DAY Inhibit Vending
SET TIME-OF-DAY Free Vending
SET TIME-OF-DAY Discount Vending
XX is the currently set start
Time Interval Editing
Press the number of the time interval you
This display tells you whether
Now shows
Stop press X.XX===
Display the factory-set message, press
Select AN OUT-OF-SERVICE Message
Select a Standby Message
Machine Press Then press
Character is displayed
Select a Freevend Message
End Of Message Character
Shortcut
Drink 0. Press To view the rest of the available selections
View Machine Configuration Setting
Setting Press
Automatic vend door
Press To view the rest of the available selections
View CUP Sizes Assigned to Selections
Payout Coins
Press Then press Until the display shows something like
View Nonresettable Sales and Vend Data
SET Prices
Press Display shows XX.XX is a dollar and cents
View Total Sales by Selection Both CUP Sizes
View Data Four Different Ways
View Total Paid Sales
View Total Sales by Drink Size
View Total Sales by Individual Selection
View Total Paid Sales by Price Line
To view the total sales of each large cup selection
Clear ALL Resettable Data
Clear Paid Sales Data only
View Amount in Coin BOX Not Shown if Zero
View Amount in Validator
Not Shown If Zero
View Freevend Sales by Time Interval
View Discount Sales by Time Interval
View Free Vends Not Shown If Zero
View Winners Not Shown If Zero
View Time Data
1100 am
View Total Unpaid Sales
View Total Unpaid Vends
At 942 am
Gain Access To The Supervisor Mode on
View Number of Test Vends
View Machine ID Number
View Number of CUP Ring Cycle Failures
View Home Switch USE Related to Surevend
Cycled. Check the cup ring adjustment see Cup mechanism
View CUP Ring Cycles Related to Surevend
Display shows You may now test vend
Vend mode
Test Vend Selections and Verify Credit Added
Test the Display
Test Throw Carbonated Water
Test Drop a CUP
Test the Automatic Delivery Door
Test Throw Still Water
Test the ICE Maker
Test the Syrup Pumps
Test the Carbonator
At this
Pail and dump its contents. The display will show
Fill during the Coolsan process
Read With the time message transposed
Test Various Switches and Sensors
Input Screen 1 Definitions
Input Screen 2 Definitions
Press , then press until the display shows
View Surevend Average Calibration Value
Then press Until the display shows
View Diagnostic Messages
Display shows FINISHED. Reconfigure the merchandiser
Settings price, time, monetary options, messages, etc
Error is corrected. Check for bill stuck in the acceptance
Keyswitch input is active and configured as an inhibit
Rect config number directly on this screen without further
Power OFF and then on
Download Data to a Pdcd
SET Freevend Options
Cold Drink Center 327/328 Operator’s Guide
Index
Page
Polarity Check
Supervisor
Total Sales by Selection
View
Terms and Conditions of Sale