Trane Tracer Unit Ventilator, ZN.520 manual Data Sharing-LonWorks, Simple data sharing application

Page 43

Unit Operation

OFF due to a safety or command. The controller enters the FREEZE AVOIDANCE mode when an out- door air temperature is present (communicated or hardwired) and it is below the freeze avoidance set- point (configurable). The controller disables freeze avoidance when the outdoor air temperature rises 3°F above the freeze avoidance setpoint.

When the controller is in the freeze avoidance mode:

qAll water valves are driven open to allow water flow through the coil

qFan is OFF

qFace-and-bypass damper (when present) is in full BYPASS

qDX and electric heat are OFF

MORNING WARM-UP

The Tracer ZN.520 controller keeps the modulating outdoor air damp- er closed anytime during the OCCU- PIED mode when the space temperature is 3°F or more below the heating setpoint.

Figure 23: Simple data sharing application

The damper remains closed indefi- nitely during morning warm-up until the space temperature is with- in 2°F of the effective heating set- point. The unit runs at full capacity until setpoint is met.

COOL-DOWN

The Tracer ZN.520 controller keeps the modulating outdoor air damp- er closed for up to one hour at ev- ery transition from UNOCCUPIED to OCCUPIED mode when the space temperature is 3°F or more above the cooling setpoint.

The damper remains closed during cool-down until the space temper- ature is within 2°F of the effective cooling setpoint. The unit runs at full capacity until setpoint is met.

Data Sharing—LonWorks

Tracer ZN.520 allows peer-to-peer data communication through the use of LonWork’s technology. Data such as space temperature set- point, occupancy, etc. can be shared from a master controller to

a peer controller over a twisted pair of communication wire with or without the presence of a front end

building management system. (See Figure 23: “Simple data shar- ing application”) This ability al-

lows units to operate with the same data to prevent conflicting control.

Data sharing is established through the use of “bindings”. Bindings are set up through the Rover service tool.

The Tracer ZN.520 controller in- cludes a network variable for mas- ter/slave operation. This variable includes all of the information re- quired for the slave units to oper- ate with master controller. (See

Figure 24: “More complex data sharing application”)

For more information on establish- ing bindings, see the Rover service tool manual. For a complete listing on shared points see “Appendix— Data Lists” on page64.

46

UV-SVP01A-EN

Image 43
Contents Tracer ZN.520 for Classroom Unit Ventilator Installation Owner DiagnosticsInstallation of New Units Start-up ProceduresPower Up Sequence Tracer ZN.520 Overview General InformationGeneral Information Tracer ZN.520 unit controller circuit board Controller Circuit Board FeaturesService Controller FeaturesTypical Components Peer-to-Peer Communications Communication ConfigurationsIntegrated Comfort System Communication Interface Stand-AloneInteroperability Description End Device SpecificationsCharacteristic Standard End DevicesStandard End Devices Way Control Valve Time clock Zone sensor Dpdt Control Transformer Specifications Installation and WiringBinary Inputs Generic/baseboard Heat Binary Output Binary OutputsAnalog inputs Analog InputsMounting Vertical classroom unit ventilator end pocket Power WiringProper zone sensor placement Installing the Wall- Mounted Zone Sensor OptionalHumidity and CO2 Sensors Typical Wiring Diagram-Wall Mounted Zone Sensor Typical Wiring Diagram-Unit Mounted Zone Sensor Typical Wiring Diagram-Unit Input and output summary Input/Output SummaryInput/Output Summary Heating source ConfigurationConfigurable parameters Cooling sourceBinary Outputs1 Analog input summary Binary input summary ConfigurationBinary Inputs1 Analog Inputs1Default Fan ConfigurationEnd Device Configurations Fan configuration rangesDischarge Air Limits Setpoint defaults Default Valid rangeDischarge air limit ranges Default Valid range SetpointsPower-Up Control Wait Occupied Bypass TimerMaintenance Timers Unit Identification Tag Location IdentifierWinking Occupancy Power-UpUnit Operation Heating And Cooling Changeover LogicHeat/Cool Changeover logic Fan Operation Fan Off DelayCooling Operation Heating OperationModulating Valves Valve OperationFace-and-Bypass Damper Operation Exhaust fan/damper operationTemperature Assumed1 Entering Water Temperature SamplingWater assumption chart Unit ConfigurationBaseboard Heat Operation Economizer OperationDX Operation Electric Heat OperationOther Modes Filter Status/ Maintenance TimerOutput Overrides Fan StatusSimple data sharing application Data Sharing-LonWorksMore complex data sharing application Heating And Cooling Changeover Logic Heat/Cool Changeover logic Cooling Operation Valve Operation Entering Water Temperature Sampling Economizer Operation Output Overrides Data Sharing-LonWorks More complex data sharing application Yellow Comm LED TroubleshootingRed Service LED Black Service Push ButtonExit6 Test ProcedureTroubleshooting Outdoor Air Temperature Failure Space Temperature FailureEntering Water Temperature Failure Discharge Air Temperature LimitDiagnostics Troubleshooting Translating Multiple Diagnostics Fans Rover service toolValves stay closed Probable cause Possible Explanation ValvesValves stay open Probable cause Possible Explanation Outside Air Damper DX/Electric HeatOutdoor air damper stays closed Probable cause Explanation Probable Cause Explanation Outdoor air damper stays openReplacing Circuit Boards Tracer ZN.520 Unit Controller ReplacementAppendix Hardwired Setpoint AdjustmentFan Switch Resistance Values Hardwired Thermistor ValuesFunction Appendix-Binary ConfigurationBinary Configuration Binary configuration details Binary input or outputUnit Operation Based On The Effective HEAT/COOL Output Heat/cool mode input NviHeatCoolEffective heat/ cool mode output nvoHeatCool Appendix-Unit OperationAppendix-Unit Operation Input/output listing1 Configuration properties1Appendix-Data Lists Data ListsSet the Program Setting the Time ClockAppendix-Timeclock Set the Time and DayOverride Program Manual Operation Review and Change ProgramsAppendix-Timeclock Appendix-Location Identifier Location Identifier Location Identifier Location Identifier Trane Company