Russound CAM6.6X-S1/S2 instruction manual Power on CMD OnCmd, Command Type

Page 63

INSTALLER

INSTALLATION MENU

All sources that have power management enabled are initialized by a “POWER ON” command/ macro. Power management is initialized when the first keypad is turned on or when the home theater trigger input has 12VDC present. The 12VDC trigger output is turned on when the first zone is turned on.

All sources that have power management enabled are turned off by the “POWER OFF” command after all zones have been turned off, with a timeout of five minutes.The 12VDC trigger output is turned off one minute after that. This timeout is postponed for as long as the home theater trigger input has 12VDC present. See Power Management - Flow Chart page 76

1. SOURCE NUM Select the source number this feature will be configured for. (Src #)

2.POWER ON CMD – (OnCmd)

Tells the controller to turn on the selected source equipment (by SOURCE NUMBER) when any of the UNO System Keypads is turned on. If “no,” procedure advances to POWER OFF CMD (step 6)

3. COMMAND TYPE

Select the type of source command (e.g., CD, TV, etc.).

(CmdTp)

 

a. Selected: Learned IR

Choose Learned IR if the pre-programmed IR code library does

(LrnIR)

not support the source component.

i. LEARNED SRC –

Select the learned source bank to be assigned to the source

(LnSrc)

component. Procedure advances to KEY FUNCTION (step 5)

b. Selected: Unassigned

The Power On command is cleared. Procedure advances to

(Unasg)

POWER OFF CMD (step 6)

c. Selected: Default

Default selects the same device type and device code previously

(Deflt)

setup in BASIC SETUP. Procedure advances to KEY FUNCTION

 

(step 5)

d. Selected: Macro:

(To build macros, see Macro Editor page 65)

i. MACRO -

Macro loads a series of commands which are processed when

(Macro)

activated.

ii. MACRO ID

Enter the macro ID number. Menu advances to POWER OFF CMD

(MacID)

(step 6)

e. All Other Selections:

Procedure advances to DEVICE CODE (step 4)

4. DEVICE CODE

Source component code for IR control.

(DevCd)

 

5. KEY FUNCTION --

Select a function (Play, Enter, etc.).

(KeyFn)

 

63

Image 63
Contents CAM6.6X-S1/S2 System Important Safeguards Table of Contents Reference Section Making ConnectionsOperation Component GuidesProduct Introduction Main Power and Zone Status Component GuideCAM6.6 Controller-Front Panel UNO-S1 Keypad-Front Panel BluesUNO-S2 Keypad-Front Panel CD PlayerFavorite 2 preset selections UNO-LRC1 Remote ControlUNO-S1 Keypad OperationUNO-S1 User Menu Operation User Menu SettingsFeature and Setting Party Party Mode Master or OffF1 and F2 Buttons UNO-S2 KeypadBalance Feature and Setting 1. BassUNO-S2 User Menu Operation TrebleInternal Source XM Tuner XM Radio OverviewDisplay Condition XM Radio Modes Category Search Now Playing Display PreferencesUNO-S1 UNO-S2 UNO-LRC1 Next Bank Next PresetPrevious Preset Preset ModeCategory Channel Up Category Search ModeNext Category Previous CategoryChannel Name CH Name Now Playing ModeDisplay Preference Mode Channel Number CH NumberUNO-S1 Keypad Control UNO-S1 Keypad Control of Tuner Selecting the tunerSelecting the desired channel UNO-S2 Keypad Control UNO-S2 Keypad Control of TunerXM Classics Recall Last Channel Setting a Memory PresetUser System Programming Overview Installation MenuSetup Menu Flow Charts Sample ConfigurationsCAM6.6X-S1/S2 System Components Tools needed for installationGetting Started Unpacking the System ComponentsSpeaker Wiring Wiring InstructionsKeypad Wiring CAT-5 Wire Color TypeCAM6.6 Controller-Rear Panel Installer Data Rx TTL Level Data Tx TTL Level GND +12VDC UNO-S1 Keypad-Update PortCAT-5 Connection UNO-S1 Keypad-CAT-5 Connection+12VDC UNO-S2 Keypad-Update PortData Rx RS-232 Data Tx RS-232 GNDUNO-S2 Keypad-CAT-5 Connection Keypad Location UNO-S1 KEYPAD-INSTALLATIONUNO-S2 KEYPAD-INSTALLATION UNO Keypad Port Connection CAM6.6 with Optional Internal Source XM satellite radio Source Audio and IR Input ConnectionsSource Audio Connections Source IR ConnectionsCommon IR Connections Common IR ConnectionSpeaker Connections Zone Fixed/Variable Audio Outputs 12VDC Home Theater Trigger In/Out 12VDC Home Theater Trigger12VDC 100mA Trigger Out 12VDC Mute Trigger In/Out 12VDC Mute Trigger12VDC Mute Trigger Out Rnet Link In and Link Out RS-232 Interface XM Signal Strength Mode Optional Internal Source XM Tuner AntennasXM Antenna Initial Install Test Number of Sources # of Sources/SOURCE Setup Flow Charts PagesInstallation Menu Pages Controller Setup Ctrlr SetupNumeric IR Source Setup Pages Basic Setup Source Setup PagesPeripheral Setup Pages 53-55 for Optional Internal Source Source Volume Trim Source SetupSetup Forms Mute Installer UNO-S1 Keypad Five-Character Display Installation Menu OverviewMemory # Memory NameBank # Are you sure? Sure? Please Wait Cycle Power Bank NameAll controllers Version Command TypeBuild Time Build DateSelected Unassigned Unasg KEY Name Device CodeKEY Function Save CHANGES? Trim LevelHighest NUM Suffix CMD Numeric TextPrefix CMD Selected Learned IRSRC SEL CMD SrcSC SysOn ZonVT Each zone. -16 dB lowest to 0 dB max-3dB defaultSyson Enable ZON VOL TrimInstallation Menu Power on CMD OnCmd Learned SRC Learn IR LrnIRMacro ID Command NUMLEARN/DELETE SUCCESS?#CONTROLLERS Peripheral Setup Memory Name, Bank Name Menu Flow ChartsSetup Menu Flow Charts Installer Periph Setup Installer Installer Mute Installer Installer LED on rear CAM Panel Blinks fast Installer Installer Device Codes for Video Acc IR CodesDevice Codes for TVs Device Codes for CableDevice Codes for SAT/DSS Device Codes for VCRsDevice Codes for Laser Disc Players Device Codes for CD Players Device Codes for DVD PlayersDevice Codes for Tuner/Amp Device Codes for Amp and Misc. AudioKEY Function UNO-S1 TV Hdtv KEY Codes TV HdtvSAP SAP, CC KEY Function UNO-S1 Cable KEY Codes CableSAP KEY Function UNO-S1 Video ACC KEY Codes Video ACCLanguage, MTS KEY Function UNO-S1 SAT/DSS KEY Codes SAT/DSSAlt/Audio,Lang.,CC KEY Codes VCRKEY Function UNO-S1 VCR KEY Codes VCR KEY Function UNO-S1 Laser Disc KEY Codes Laser DiscSubtitle, CC KEY Function UNO-S1 DVD KEY Codes DVDFormat Wide,Zoom,Aspect KEY Function UNO-S1 Receiver KEY Codes ReceiverDVD, LD KEY Function UNO-S1 AMP/MISC Audio KEY Codes AMP/MISC AudioTAPE, MD KEY Function UNO-S1 KEY Codes CDInput Tape, MD KEY Function UNO-S1 Home Control KEY Codes Home ControlInput Source/Scene UNO-S1 UNO-S2 Source NamesTivo Multiple Controllers with ONE Tuner Sample ConfigurationsMultiple Controllers with TWO Tuners ST2-XM Tuner Back Panel Multiple Controllers with Three TunersST2-XM Tuner Back Panel Multiple Controllers with ST2 Dual TunerTechnical Specifications Warranty & Repair 113 114 115