GE JVM2070_H manual Cavity Thermal Cutout TCO, Magnetron Thermal Cutout TCO, Fuses, Removal

Page 13
Cavity Thermal Cutout (TCO)

Cavity Thermal Cutout (TCO)

The cavity TCO is located on the top of the microwave oven on the left side of the forward vent duct. The microwave oven shuts off when the temperature of the cavityTCO reaches 212°F (100°C).

The cavity TCO is a normally closed switch. An open reading across the TCO indicates an overtemperature condition or failed TCO. The cavity TCO is not resettable.

Removal

Remove the microwave (see Microwave Removal and Component Access).

Slide the cavity TCO from the two tabs and remove the 2 connectors.

Cavity TCO

Magnetron Thermal Cutout (TCO)

The magnetron TCO is located on the magnetron and shuts off when the magnetron temperature reaches 150°F (65.5°C).

The magnetron TCO is a normally closed switch. An open reading across the TCO indicates a failed TCO. The magnetron TCO is resetable

Removal

Remove the microwave (see Microwave Removal and Component Access). Disconnect the 2 wires and remove the screws from the magnetron TCO.

Fuses

The main and high voltage transformer fuses are located behind the hidden vent, above the control panel.

Removal

Remove the hidden vent (see Microwave Removal and Component Access).

Remove the grille to access the fuses.

– 13 –

Image 13
Contents 2/04 PUB #TECHNICAL SERVICE GUIDE Over the Range Microwave Oven MODEL SERIES JVM2070HTechnical Service Guide Copyright IMPORTANT SAFETY NOTICERECONNECT ALL GROUNDING DEVICES GE Consumer & IndustrialA. DO NOT OPERATE OR ALLOW THE OVEN TO BE OPERATED WITH THE DOOR OPEN Table of Contents Feature Pack InstallationNomenclature Model NumberTouchscreen Display Control FeaturesHELP HOMETop View Component Locator Views1 - Magnetron 2 - Magnetron Thermal Cutout TCO Right Side View3 - High Voltage Transformer 4 - Magnetron Cooling Fan Motor and Blade 5 - High Voltage CapacitorComponents Microwave Removal and Component AccessExhaust Fan RemovalSide Stirrer Side Stirrer MotorTop Stirrer Top Stirrer MotorCooling Fan and Motor Magnetron Thermal Cutout TCO Cavity Thermal Cutout TCOFuses Gas Sensor MagnetronTransformer Interior Light Hidden Vent MotorDoor Sensing and Primary Interlock Switches Door Interlock SwitchesMonitor Switch Control PanelDoor Sensing Switch Interlocks Door Latch SwitchesPower Relay Primary Interlock Switch TestHigh Voltage Capacitor Removal and ReplacementBottom and Hood Thermal Cutout TCO Turntable MotorSurface Lamps Surface Lamp AssembliesControl Performance Test TroubleshootingSensor Test Quick Test Error Message Diagnostics TestDemonstration Mode Displayed InformationPerformance Test Microwave Leakage TestHigh Voltage Capacitor CN03 - Vent Blower Connector CN01 - Ribbon connectorCN04 - Cooktop Lamp Relay Connector CN06 - Door Sensing ConnectorLouver Motor Does Not Work Vent Motor Does Not Work Strip CircuitsFan Motor Does Not Work Dead Unit - Cavity or Magnetron TCO Does Not Work Top Stirrer, Side Stirrer, or Drive Motor Does Not WorkDead Unit - Bottom TCO Does Not Work FAN MOTORInterior Light Does Not Work Surface Lamps Do Not Work 2 - White Magnetron Does Not Work3 - Blue BlackWARNING Power must be disconnected before servicing this appliance Wiring DiagramCode No. DE99-00125F SchematicIllustrated Parts Catalog CATALOG NUMBER VIEW NUMBERDESCRIPTION QUANTITYPLATE MOUNTING ASM For the period of WarrantyGE will replace Full one-year