GE 175D1807P633 installation instructions Care and Cleaning/General Maintenance, Clean Pump Filter

Page 10

Operating Instructions Safety Instructions

Installation

Instructions

Consumer Support Troubleshooting Tips

Loading and using the washer.

Care and Cleaning/General Maintenance

Exterior: Immediately wipe off any spills. Wipe with damp cloth. Wipe or dust spills or washing compounds with a damp cloth. Washer control panel and finishes may be damaged by some laundry pretreatment and stain remover products. Apply these products away from the washer. The fabric may then be washed and dried normally. Damage to your washer caused by these products is not covered by your warranty. Do not hit surface with sharp objects.

Interior: Dry around the washer door opening, flexible gasket (including attached hoses) and door glass. These areas should always be clean to ensure a watertight seal.

It is recommended to rinse the washer at least once per month with 1 cup of bleach (or other commercially available product manufactured for this purpose, such as Tide® Washing Machine Cleaner) poured into the bleach section of the dispenser (no clothes) using the BASKET CLEAN cycle (found in the WASHER cycles menu).

Moving and Storage: Ask the service technician to remove water from drain pump and hoses. Do not store the washer where it will be exposed to the weather. When moving the washer, the tub should be kept stationary by using the shipping bolts removed during installation.

See Installation Instructions in this manual. If these parts are not available, they can be ordered by visiting our Website at GEAppliances.com or by calling 800.GE.CARES.

Long Vacations: Be sure water supply is shut off at faucets. Drain all water from hoses if weather will be below freezing.

Clean Pump Filter

Due to the nature of the front-load washer, it is sometimes possible for small articles to pass to the pump. The washer has a filter to capture lost items so they are not dumped to the drain. To retrieve lost items, clean out the pump filter.

1.

With a knife or slotted screwdriver, pry open the door on

Pump Filter

 

the bottom right of the front of the unit .

2.

Twist the small white cap counterclockwise a quarter turn

 

 

and unhook the small rubber hose. Pull the hose out of the

 

 

hole and remove the white drain hose plug above a small

 

 

pan to capture any water that may drain. Drain the excess

 

 

water. Replace.

 

3. Unscrew the pump filter. Rinse. Replace.

4. Close the access door.

Drain Hose

Drain Plug

Pump Filter

Cleaning the Door Gasket

Open the washer door. Using both hands, press down the door gasket .

Remove any foreign objects if found trapped inside the gasket . Make sure

there is nothing blocking the holes behind the gasket .

While holding down the door gasket, inspect the interior of the gasket by pulling it down with your fingers. Remove any foreign objects if found trapped inside this gasket . Make sure there is nothing blocking the holes behind the gasket .

When you are finished cleaning the door gasket, remove your hands and the gaskets will return to the operating position.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Features You can find them on a label inside the doorInstall or store where it will not be exposed Operating Instructions Safety Instructions InstallationConsumer Support Troubleshooting Tips To temperatures below freezing or exposedTroubleshooting Tips Consumer Support Instructions Operating Instructions InstallationGEAppliances.com About the washer control panel PowerQuick Start Control settings Wash CyclesSpin Speed Manufacturer’s care label when changing the Spin settingSoil Level Wash TempSafety Instructions Operating Consumer SupportInstallation Instructions About the washer featuresTroubleshooting Tips Sorting Wash Loads Loading and using the washerLoading the Washer Cleaning the Door Gasket Care and Cleaning/General MaintenanceClean Pump Filter With a knife or slotted screwdriver, pry open the door onUse only HE High-Efficiency detergent Fabric Care Labels Machine wash CycleTools Required for Washer Installation Parts SuppliedWhen installed in alcove Sides, Rear, Top = 0″ 0 cm Contractor DimensionsROUGH-IN Dimensions Location of Your WasherCut and remove all packaging straps Unpacking the WasherInsert shipping bolt hole covers into shipping bolt holes Grounding Requirements Hot and cold water faucets Must be installed withinElectrical Requirements Water Supply RequirementsInstalling the Washer Installing the Washer Replacement PartsBefore you call for service… Firmly touching the floor Floor. Your installer should correct this problemMachine will finish the wash cycle Pushed too far down the drain Washer pump filter maySafety Instructions Operating Instructions Installation Tips Consumer SupportWe Will Replace Instructions Safety InstructionsWhat Is Not Covered in the United States Warrantor General Electric Company. Louisville, KYGE Washer Warranty. For customers in Canada What Is Not Covered in CanadaSafety Instructions Mesures de sécurité Fonctionnement Installation Inscrivez ici les numéros de modèle et de sérieInstallez ou placez votre laveuse dans un endroit où Conseils de dépannage consommateurSécurité Fonctionnement Installation DépannageLe panneau de contrôle de votre laveuse Fonctionnement Mesures de sécurité InstallationPower alimentation Démarrage rapideCycles de lavage Spin Speed Vitesse d’essorage Réglage des contrôlesSoil Level Niveau de saleté Wash Temp Température de lavageLock Verrouillage Delay Start Mise en marche retardéeExtra Rinse Rinçage extra My Cycle FavoriMesures de Les caractéristiques de votre laveuseSécurité Conseils de dépannageChargement de la laveuse Chargement et utilisation de la laveuseTri des charges de lavage CouleursFonctionnement Mesures de sécurité Installation DépannageSoins et nettoyage/Entretien général Nettoyage du filtre de pompeUtilisez seulement un détergent à haute efficacité HE Étiquettes de tissus Utilisez seulement un détersif à haute efficacité HEClé fournie Pince multiprise à crémaillère Niveau à bulle Outils Nécessaires Pour Installer LA LaveusePièces Fournies Clé Tuyaux d’eau Guide de tuyau Raccords de tuyauDimensions DE L’ENTREPRENEUR Emplacement DE Votre LaveuseDimensions Avertissement Recyclez Déballage DE Votre LaveuseExigences DE Mise À LA Terre Vous Devez installer des robinets d’eau chaude et froideExigences Électriques Exigences D’ALIMENTATION D’EAUInstallation DE LA Laveuse La main, puis en serrant encore 2/3 de tour avec desInstallation DE LA Laveuse suite Pièces DE RechangeAvant d’appeler un réparateur… Vidangeletuyaudevidange La laveuse et le drain Votre installateur devrait corriger ce problèmeOumalbranché Ne le bloque pas Lavidangedelamaisonest Lefiltredelapompeàeau’alimentationd’eauestcoupée Lalaveusen’estpasbranchéeDans une prise de courant sous tension LedisjoncteurabasculéMachine Cleaner. Consultez la section Entretien et Calgon ou installez un adoucisseur d’eauExécutez un cycle BasketClean Nettoyage du panier Aient assez d’espace pour bougerCe qui n’est pas couvert au Canada Garantie de laveuse GEPour une période de Nous remplacerons Un anStudio de conception réaliste Soutien au consommateur Service de réparationsPièces et accessoires Prolongation de garantieConsumer Support

175D1807P633 specifications

The GE 175D1807P633 is a notable component within the realm of industrial automation and control systems, showcasing the ingenuity and advanced capabilities synonymous with General Electric. This specific model is recognized for its robustness and reliability, making it a go-to choice for industries that require precision and efficiency.

One of the main features of the GE 175D1807P633 is its compatibility with various industrial environments. Built to withstand challenging conditions, it excels in situations characterized by extreme temperatures and vibrations, enabling it to function seamlessly in manufacturing plants, energy sectors, and other demanding applications. This durability is crucial in minimizing downtime, ensuring that operations continue smoothly.

The GE 175D1807P633 incorporates cutting-edge technologies that enhance its performance. One of these key technologies is its advanced signal processing capabilities, which allow for greater accuracy and faster response times. This feature is particularly important in automation processes where timing is critical. Additionally, the unit often includes built-in diagnostics that offer real-time monitoring, enabling users to anticipate and address potential issues before they escalate into significant problems.

Another important characteristic of the GE 175D1807P633 is its user-friendly interface. Designed with operators in mind, it allows for straightforward integration with existing systems. This ease of integration is further supported by a variety of communication protocols, streamlining data exchange and enhancing collaboration among different components within an industrial setup.

The versatility of the GE 175D1807P633 is another highlight, as it can be utilized in numerous applications ranging from process automation to discrete manufacturing. Its adaptability makes it suitable for a variety of industries, including automotive, pharmaceuticals, and food processing.

Furthermore, this model is designed with energy efficiency in mind, aligning with modern sustainability goals. Its operational efficiency not only reduces energy consumption but also translates into cost savings for companies that deploy it.

In conclusion, the GE 175D1807P633 stands out as a powerful, adaptable, and efficient component in the industrial automation landscape. With features that enhance performance and reliability, it exemplifies GE’s commitment to innovation and excellence in engineering, making it a preferred choice for industries striving for optimized operational efficiency.
Top Page Image Contents