GE 165D4700P381 Spots and filming Extremely hard water, On glasses, Prevent new film buildup

Page 17

ge.com

Problem

Possible Causes

What To Do

Spots and filming

Extremely hard water

Use Jet-Dry®or Cascade Crystal Clear® rinse agents to remove spots and

on glasses and

Low inlet water temperature

prevent new film buildup.

flatware

Make sure water temperature is at least 120°F.

Overloading the dishwasher

 

Load dishwasher as shown in the Loading Place Settings section.

 

Improper loading

 

Make sure detergent is fresh.

 

Old or damp powder detergent

 

If water is extremely hard, a softener may be required.

 

Rinse agent dispenser empty

 

 

Too little detergent

 

Cloudiness on

Combination of soft water and

This is called etching and is permanent. To prevent this from happening,

glassware

too much detergent

use less detergent if you have soft water. Wash glassware in the shortest

 

 

cycle that will get them clean.

 

Water temperature entering

This could be etching. Lower the water heater temperature.

 

the dishwasherexceeds 150°F

 

Suds in the tub

Correct detergent

Use only automatic dishwasher detergents to avoid sudsing.

 

wasn’t used

 

Cascade® and Electrasol® Automatic Dishwashing Detergents

 

 

 

have been approved for use in all GE dishwashers.

 

 

To remove suds from the tub, open the dishwasher and let

 

 

 

suds dissipate. Close and latch the dishwasher door. Pump out water

 

 

 

by touching the START/RESET pad once; then 30 seconds later,

 

 

 

touch the START/RESET pad again. Repeat if necessary.

 

Rinse agent was spilled

Always wipe up rinse agent spills immediately.

Detergent left in

Dishes are blocking the

Reposition the dishes, so the water from the lower spray arm can

dispenser cups

detergent cup

flush the detergent cup. See pages 13 and 14.

Water in the

Cap not tightened after filling

Use a turkey baster to remove as much water as possible from the

SmartDispense

the dispenser

SmartDispensedispenser and refill it as normal. Be sure to tighten the

dispenser

 

cap fully to prevent water from entering the dispenser.

Black or gray

Aluminum utensils have

Remove marks with a mild, abrasive cleaner.

marks on dishes

rubbed against dishes

 

Dishes don’t dry

Low inlet water temperature

Make sure inlet water temperature is at least 120°F.

Select HEATED DRY.

Use PRE-WASH or ADDED HEAT options.

Select a higher cycle, such as ANTI-BACTERIAor COOKWARE.

 

Rinse agent dispenser is empty

Check the rinse agent dispenser and fill as required.

Controlpanelresponded

Door latch may not be properly

Make sure the door is firmly closed.

toinputsbutdishwasher

seated

 

 

neverfilled with water

Water valve may be turned off

Make sure water valve (usually located under the sink) is turned on.

Stained tub interior

Some tomato-based foods can

Use of the RINSE AND HOLD cycle after adding the dish to the load

 

causereddish stains

 

can decrease the level of staining. GE recommends Cascade®

 

 

 

 

Plastic Booster to help remove these types of stains.

 

 

Tea or coffee stains

Remove the stain by hand, using a solution of 1/2 cup bleach

 

 

 

 

and 3 cups warm water.

 

 

 

 

WARNING

 

 

 

 

Before cleaning interior, wait at least 20 minutes after a cycle for the

 

 

 

 

heating elements to cool down. Failure to do so can result in burns.

 

An overall yellow or brown film can •

A special filter in the water supply line is the only way to correct

 

be caused by iron deposits in water this problem. Contact a water softener company.

 

White film on inside surface—

GE recommends Jet-Dry®or Cascade Crystal Clear® to help

 

hard water minerals

 

prevent hard water mineral deposits from forming.

Run dishwasher with citric acid to remove mineral deposits. Citric acid (Part number: WD35X151) can be ordered through GE Parts.

17

Safety Instructions

Operating Instructions

Troubleshooting Tips

Consumer Support

Image 17
Contents You can find them on the tub wall just inside the door Write the model and serial numbers here Model # Serial #Reboot Troubleshooting TipsOperating Instructions Consumer SupportGe.com SupportSafety Instructions Control SettingsTroubleshooting Tips Consumer Support About the dishwasher control panelMedium 7.5 gal., 95 min Heavy 8.8 gal., 105 minLight 6.3 gal., 85 min EstablishmentsFront-Control Dishwashers EnhancementsStart Status Indicator Lights What It Means CleanFlashing display lights Recommended dishwasher productsCheck the Water Temperature Using the dishwasherUse Jet-Dryor Cascade Crystal Clear Rinse Agent Dish Preparation Prior to LoadingManual Detergent Dispenser SafetyInstructions Filling Manual Detergent DispenserSmartDispense SmartDispenseTM Detergent Dispenser some modelsCalibrationofModelsWithouta3-DigitDisplay Determine the Hardness of Your Tap WaterFront controls Top controlsAdjustable Upper Rack Troubleshooting Tips SupportLoading the dishwasher racks Upper RackRemoving the Upper Rack SafetySilverware Basket Then fill the lower rack and begin your cycleExtra Rack Features on some models Loading place settings…Caring for the dishwasher Safety Instructions Operating Instructions Before you call for service…Error Messages Possible Causes What To Do Problem Possible Causes What To DoCycle that will get them clean Flatware Make sure water temperature is at least 120FThis could be etching. Lower the water heater temperature Make sure inlet water temperature is at least 120FSetting controls Water standing Go off when you’reControl panel lights Water won’t pumpWarrantor General Electric Company. Louisville, KY GE Dishwasher WarrantyFor The Period GE Will Replace Consumer Support Lave-vaisselle Conseils de dépannage Instructions de FonctionnementAvant de jeter votre vieux lave-vaisselle En ce sens, voyez les recommandations du fabricantConseils de dépannage Soutien au Réglage des contrôles Le panneau de contrôle du lave-vaisselleInstructions de sécurité Soutien au consommateur Conseils de dépannageProgrammes de lavage sélections Conseils de dépannage Soutien au consommateurOptions START/RESET mise en marche/remise à zéroEt attente Rinse and Hold rinçage et attenteVoyants lumineux qui clignotent Produits de lavage de vaisselle recommandésAu consommateur Mise en marcheVérifiez la température de l’eau Utilisation du lave-vaissellePréparation de la vaisselle avant son chargement Vous avez oublié de la vaisselle?De sécurité Distributeur manuel de détergentDe dépannage Soutien au consommateur Remplissage du distributeur manuelUn distributeur plein dure environ 1 mois d’usage normal Distributeur de détergent SmartDispenseMD certains modèlesPrenez soin de ne pas mélanger un détergent Instructions Commandes sur le hautTrouvez la dureté de votre eau d’alimentation Après avoir réglé la dureté de l’eau, appuyez surSécurité Chargement des paniers de votre lave-vaissellePanier supérieur Panier supérieur ajustablePanier à argenterie ConsommateurEnlèvement du panier supérieur Chargement des couverts… Chargement des paniers du lave-vaisselleSoutien Soins de votre lave-vaisselleProblème Causes possibles Ce qu’il faut faire Avant d’appeler le service de réparations…Causes possibles Ce qu’il faut faire Détergent qui reste Voile sur les verresDans les réservoirs Du distributeur Eau dans leLe lave-vaisselle EnréglantlescommandesNe fonctionne pas De la cuveInstructions de sécurité Fonctionnement Garantie GE sur les lave-vaissellePour une période de GE remplacera Ce qui n’est pas couvertPièces et accessoires Soutien au consommateur Service de réparationsStudio de conception réaliste Prolongation de garantie

165D4700P381 specifications

The GE 165D4700P381 is a notable component in the field of electrical engineering, primarily recognized for its application in various industries that require reliable and efficient electrical power management. This product serves as a key element in power distribution systems, ensuring stable performance and effective load management.

One of the main features of the GE 165D4700P381 is its robust design. Engineered to withstand harsh environmental conditions, this device is built with high-quality materials that offer durability and longevity. It is suited for both indoor and outdoor applications, making it a versatile solution for different settings.

The technology embedded within the GE 165D4700P381 reflects the latest advancements in power management systems. It is designed to operate efficiently in a range of temperatures and humidity levels, ensuring optimal functionality regardless of the surrounding environment. This adaptability is critical for industries that face fluctuating conditions, allowing for uninterrupted service.

The GE 165D4700P381 also features integrated protective mechanisms that enhance its safety. With built-in fault detection and prevention systems, it minimizes the risk of electrical failures, thereby protecting connected devices and reducing maintenance costs. These safety features are crucial for applications in sectors such as manufacturing, utilities, and telecommunications, where system reliability is paramount.

Additionally, the GE 165D4700P381 is equipped with advanced connectivity options. This enables seamless integration with smart grid technologies and IoT devices, facilitating real-time monitoring and management of electrical power systems. The ability to connect with digital infrastructure supports enhanced data analytics, allowing businesses to optimize their energy consumption and improve operational efficiency.

Overall, the GE 165D4700P381 stands out as a dependable solution for those seeking to enhance their power management capabilities. Its combination of robust construction, advanced technology, and safety features makes it an ideal choice for various industrial applications. As energy demands grow and systems evolve, the GE 165D4700P381 continues to play a vital role in ensuring reliable electrical performance across multiple platforms.