Thermador PH42GS Installation Instructions, Wall Mount Installation, Installation Specifications

Page 10

Installation Instructions

Wall Mount Installation

Installation Specifications

Figure 6 shows a typical installation of the hood with a duct cover. Accessory 6” (152 mm) and/or 12” (305 mm) duct covers are used to fill the space between the hood and ceiling (available for purchase separately).

The installation height ranges from a minimum height of 30” (762 mm) to a maximum height of 40” (1016 mm); however, it is necessary to follow the cooking appliance manufacturer’s installation instructions for proper hood height. In Figure 6 one 6" (152 mm) duct cover has been used in this installation. Add or subtract duct covers as appropriate to accommodate ceiling height and recommended hood height.

The duct cover structure is supported by the hood.

6” Duct

Cover

24” (610 mm)

18” (457 mm)

24” (610 mm)

Hood mounting Heights

Minimum 30” (762 mm)

or 27” (687 mm)

Maximum 40” (1016 mm)

Hood Depth

 

*Follow cooking appliance manufacturer’s recommendations

Figure 6: Typical Hood Installation

NOTICE:

The hood could incur some damage from heat if a THERMADOR PROFESSIONAL® series range or rangetop is operated with multiple burners at high settings under a hood that is installed at minimum clearances.

1.After the hood installation height has been determined, draw a horizontal line at a distance above the cooktop equal to the recommended hood installation height plus 15½” (394 mm). This line is the mounting location of the wooden bracket shipped with the hood.

2.Find the centerline of the hood. Draw a vertical line along this centerline up to the horizontal line drawn in Step 1.

3.The hood is mounted to the wall using the wooden bracket shipped with the hood. Remove the wooden bracket located at the top side of the hood by removing the two shipping screws. Mark the center line of the wood bracket.

4.Locate a stud on both sides of the hood centerline to use for mounting the wooden bracket as shown in Figure 7.

Cooktop Centerline

Wall Studs

Wooden

Bracket

Screws 2 ea 3” (76 mm)

Recommended

Hood HeightDrywall +15½” (394 mm)

To Cooking Surface

Figure 7: Mounting the Wooden Bracket

5.Align the top of the wood bracket along the horizontal line drawn in Step 1. Align the centerlines of the bracket and cooktop.

6.Drill a 3” (76 mm) deep 3/16” (3 mm) tap hole through the wooden bracket, wall, and into the stud.

7.Use (2) or (3), depending on model, 3” (76 mm) screws to attach the bracket to the wall, as shown in Figure 7. For support of longer hoods, use three studs.

Countersink the screw heads to prevent interference with the hood.

English 8

Image 10
Contents Installation Manual Table of Contents Safety Codes and Standards SafetyBefore You Begin Grounding Instructions To Reduce The Risk Of Fire Or Electric ShockGeneral Information Installation PreparationParts Included Ducting Recommendations Considerations Before Installing HoodDuctwork Preparation Tools and Parts NeededEquivalent Duct Lengths for Commonly Used Transitions Length ftElectrical Data on the Data Rating Plate Electrical RequirementsHood Preparation Discharge DirectionAssembly of the Transition Hood TransitionInstallation Specifications Installation InstructionsWall Mount Installation Hood mounting HeightsWooden Bracket Hood SizeDuct Covers Assembly & Installation optional Screw quantity dependent on hood sizeHood Cabinet InstallationPlan View of Cabinet Cutout Tap Holes Conduit HolesSKU CFM Blower Motor InstallationIntegral Blower Installation Only AmpsWiring the Hood with an Integral Blower Wiring the Hood with a Remote BlowerWiring the Hood with an Inline Blower VTI1010D Inline BlowerWire Routing Instruction Route wires here Wire CoverHalogen Light Replacement Installing Grease Trays, Filters and SpacersHeat Lamp Replacement some models Table des matières Préparation de linstallationInstructions d’installation Consignes de sécuritéApprouvées Pour Utilisation Résidentielle Seulement SécuritéAvant de commencer Cet appareil est conforme aux normes suivantesInstructions de mise à la terre Renseignements sur la planification Préparation pour linstallationRenseignements généraux Renseignements sur la planificationPréparation du conduit daération Facteurs à prendre en compte avant d’installer la hotteRecommandations pour le conduit Outils et pièces requisesPage Type de conduit Pièce po équivalente pi Tableau 1 Longueur du ConduitPréparation de la hotte Données électriques sur la plaque signalétiqueExigences électriques Orientation du débouchéRaccord de hotte Assemblage du raccordSpécifications relatives à l’installation Instructions d’installationInstallation murale AvisDimension DE LA Hotte Vis de 3 po Mm chacune Support En boisMm M Installation sous une armoire La quantité de vis dépend de la taille de la hotteTrous à vis a Ouverture pour Le conduit B Dimension DEVue en plan de l’ouverture pratiquée dans l’armoire LA HotteTension Pour l’installation d’un ventilateur intégré seulementVentilateur Câblage de la hotte avec un ventilateur intégré Les fils à laCâblage de la hotte avec un ventilateur à distance Dia.97/8poCâblage de la hotte avec un ventilateur de conduit Ventilateur de conduit VTI1010DAcheminement des câbles Trajet des fils pour le débouché verticalRemplacement des ampoules halogènes Remplacement des lampes infrarouges certains modèlesInstalación Índice de materiasSeguridad Instrucciones de instalaciónSolamente Para UN USO Residencial SeguridadEste aparato cumple con las siguientes normas Instrucciones para la toma de tierra Para Reducir Los Riesgos De Incendio O De Descarga EléctricaInformación general Preparación para la instalaciónInformación acerca de la planificación Herramientas y piezas necesarias Factores a tener en cuenta antes de instalar la campanaRecomendaciones para el conducto NotaPage Pieza de conducto Datos eléctricos de la placa señalética Orientación de la salidaRacor de campana Ensamblaje del racorEspecificaciones acerca de la instalación Instrucciones de instalaciónAviso Dimensión DE LA Campana NotaLínea central del racor Instalación bajo un armario DE LA DimensiónAgujeros para Abertura para el Tornillos ConductoTensión Para la instalación de un ventilador integrado sóloVentilador Cableado de la campana con un ventilador integrado Figura 17 Ubicación de las clavijas soldadasCableado de la campana con un ventilador a distancia Caja de conexiones Figura 12 en la páginaCableado de la campana con un ventilador en línea Figura 22 Ventilador en línea VTI1010DRecorrido de los cables con la salida vertical Instrucciones para el recorrido del cableadoRecorrido de los cables con la salida horizontal Reemplazo de las lámparas infrarrojas algunos modelos Reemplazo de las bombillas halógenasPage Pièces et Accessoires ServiceParts & Accessories Entretien
Related manuals
Manual 38 pages 59.84 Kb

PH36GS, PH30HS, PH36HS, PH42GS, PH48GS specifications

The Thermador PH54GS, PH48HS, PH48GS, PH42GS, and PH36HS are a distinguished range of built-in refrigeration solutions, seamlessly combining style, efficiency, and advanced technology to enhance any kitchen environment. Each model in this collection is designed to provide optimal food preservation while offering a variety of features that cater to the needs of modern culinary enthusiasts.

The Thermador PH54GS features a spacious 54-inch design that offers ample storage space for all your cooling needs. It boasts a top-of-the-line cooling system that maintains consistent temperatures, ensuring fresh food for longer periods. The model incorporates a sleek stainless-steel finish that adds elegance to any kitchen. Furthermore, advanced magnetic door seals help retain cold air, leading to energy efficiency.

The PH48HS is another stunning model that measures 48 inches. It comes equipped with the innovative Cool Air Flow system, providing even airflow and temperature distribution throughout the interior. This model also features a unique Dual Compressor system that minimizes temperature fluctuations, keeping food fresher longer. Additionally, LED lighting illuminates the interior, allowing for easy visibility and a premium look.

Moving to the PH48GS, this 48-inch unit champions flexibility with adjustable shelving and various storage compartments. Its high-quality glass shelves can hold heavy items while allowing bright LED lights to shine through, enhancing visibility. The unit is also equipped with a filtered water dispenser, ensuring clean drinking water is readily available.

The PH42GS, a 42-inch option, offers similar features with a focus on convenience. Its integrated ice maker supplies a steady stream of fresh ice, perfect for entertaining or daily hydration. The model also boasts a sophisticated touchscreen control panel that allows users to personalize their cooling settings with ease.

Lastly, the PH36HS is a compact yet powerful 36-inch refrigeration solution. Its sleek design and smart storage solutions, like adjustable bins, make it ideal for smaller kitchens without compromising on functionality. This model also emphasizes energy savings, designed with insulation that minimizes energy loss.

In conclusion, the Thermador PH series is an exceptional choice for discerning homeowners seeking stylish, efficient refrigeration. With innovative technologies, ample storage, and customizable options, these models redefine luxury and functionality in the kitchen.