Thermador PH48GS, PH54GS, PH48HS Wiring the Hood with an Inline Blower, VTI1010D Inline Blower

Page 16

1.Remove junction box channel covering the wires (see Figure 12 on page 10).

2.Remove circular knockouts (Figure 12 on page 10).

3.Install 1” (25.4 mm) conduit connectors.

4.Run black, white, and green wires (#12 AWG) in 1” (25.4 mm) conduit from the power supply to the junction box.

5.Connect the power supply wires to the hood wires in the following order: black to black, white to white, and green wire to green ground screw on chassis. Use spring type wire nuts supplied.

•Lost or missing wire nuts should only be replaced with spring type wire nuts, rated for a minimum of two (2) #18 gauge wires and maximum of four (4) #14 gauge wires, UL & CSA rated to 600V and 302°F (150°C).

6.Connect the “pigtail” to the connector inside the junction box.

7.Run five (5) #14 AWG wires in 1” (25.4 mm) conduit from the remote blower to the second conduit connector.

8.Connect the remote blower to the pigtail wires as per Figure 21. Connect the remote blower green (ground) wire to the ground screw in the junction box. Refer to the blower installation instructions for further wiring details.

9.Close the junction box cover.

Wiring the Hood with an Inline Blower

To minimize noise in the kitchen, these blowers are mounted along the duct line anywhere between the kitchen and the exterior wall. If there is easy access to duct line (in an attic, for example), this may be an appealing option.

For complete installation instructions see the instructions supplied with the blower unit.

121/8"

 

12"

 

 

 

 

(305 mm)7/8" (22 mm)

(308 mm)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ø 9 7/8"

191/8"

(251 mm)

(486 mm)

 

13/4"

 

(44 mm)

 

127/8"

 

(327 mm)14 3/8"

 

(365 mm)

 

Figure 22: VTI1010D Inline Blower

English 14

Figure 23: Wiring the Hood with an Inline Blower

1.Remove junction box channel covering the wires (see Figure 12 on page 10).

2.Remove circular knockouts (Figure 12 on page 10).

3.Install 1” (25.4 mm) conduit connectors.

4.Run black, white, and green wires (#12 AWG) in 1” (25.4 mm) conduit from power supply to junction box.

5.Connect the power supply wires to the hood wires in the following order: black to black, white to white, and green wire to green ground screw on chassis. Use spring type wire nuts supplied.

•Lost or missing wire nuts should only be replaced with spring type wire nuts, rated for a minimum of two (2 #18 gauge wires and maximum of four (4) #14 gauge wires, UL & CSA rated to 600V and 302°F (150°C).

6.Connect the “pigtail” to the connector inside the junction box.

7.Run five (5) wires (#14 AWG) in 1” (25.4 mm) conduit from the inline blower to the second conduit connector.

8.Connect the inline blower to the pigtail wires as per Figure 23. Connect the inline blower green (ground) wire to the ground screw in the junction box.

9.Close the junction box cover.

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Installation Manual Table of Contents Safety Codes and Standards SafetyBefore You Begin Grounding Instructions To Reduce The Risk Of Fire Or Electric ShockGeneral Information Installation PreparationParts Included Considerations Before Installing Hood Ductwork PreparationDucting Recommendations Tools and Parts NeededEquivalent Duct Lengths for Commonly Used Transitions Length ftElectrical Requirements Hood PreparationElectrical Data on the Data Rating Plate Discharge DirectionAssembly of the Transition Hood TransitionInstallation Instructions Wall Mount InstallationInstallation Specifications Hood mounting HeightsWooden Bracket Hood SizeDuct Covers Assembly & Installation optional Screw quantity dependent on hood sizeCabinet Installation Plan View of Cabinet CutoutHood Tap Holes Conduit HolesBlower Motor Installation Integral Blower Installation OnlySKU CFM AmpsWiring the Hood with an Integral Blower Wiring the Hood with a Remote BlowerWiring the Hood with an Inline Blower VTI1010D Inline BlowerWire Routing Instruction Route wires here Wire CoverHalogen Light Replacement Installing Grease Trays, Filters and SpacersHeat Lamp Replacement some models Préparation de linstallation Instructions d’installationTable des matières Consignes de sécuritéSécurité Avant de commencerApprouvées Pour Utilisation Résidentielle Seulement Cet appareil est conforme aux normes suivantesInstructions de mise à la terre Préparation pour linstallation Renseignements générauxRenseignements sur la planification Renseignements sur la planificationFacteurs à prendre en compte avant d’installer la hotte Recommandations pour le conduitPréparation du conduit daération Outils et pièces requisesPage Type de conduit Pièce po équivalente pi Tableau 1 Longueur du ConduitDonnées électriques sur la plaque signalétique Exigences électriquesPréparation de la hotte Orientation du débouchéRaccord de hotte Assemblage du raccordInstructions d’installation Installation muraleSpécifications relatives à l’installation AvisDimension DE LA Hotte Vis de 3 po Mm chacune Support En boisMm M Installation sous une armoire La quantité de vis dépend de la taille de la hotteDimension DE Vue en plan de l’ouverture pratiquée dans l’armoireTrous à vis a Ouverture pour Le conduit B LA HotteTension Pour l’installation d’un ventilateur intégré seulementVentilateur Câblage de la hotte avec un ventilateur intégré Les fils à laCâblage de la hotte avec un ventilateur à distance Dia.97/8poCâblage de la hotte avec un ventilateur de conduit Ventilateur de conduit VTI1010DAcheminement des câbles Trajet des fils pour le débouché verticalRemplacement des ampoules halogènes Remplacement des lampes infrarouges certains modèlesÍndice de materias SeguridadInstalación Instrucciones de instalaciónSolamente Para UN USO Residencial SeguridadEste aparato cumple con las siguientes normas Instrucciones para la toma de tierra Para Reducir Los Riesgos De Incendio O De Descarga EléctricaInformación general Preparación para la instalaciónInformación acerca de la planificación Factores a tener en cuenta antes de instalar la campana Recomendaciones para el conductoHerramientas y piezas necesarias NotaPage Pieza de conducto Datos eléctricos de la placa señalética Orientación de la salidaRacor de campana Ensamblaje del racorEspecificaciones acerca de la instalación Instrucciones de instalaciónAviso Dimensión DE LA Campana NotaLínea central del racor Instalación bajo un armario Dimensión Agujeros para Abertura para elDE LA Tornillos ConductoTensión Para la instalación de un ventilador integrado sóloVentilador Cableado de la campana con un ventilador integrado Figura 17 Ubicación de las clavijas soldadasCableado de la campana con un ventilador a distancia Caja de conexiones Figura 12 en la páginaCableado de la campana con un ventilador en línea Figura 22 Ventilador en línea VTI1010DRecorrido de los cables con la salida vertical Instrucciones para el recorrido del cableadoRecorrido de los cables con la salida horizontal Reemplazo de las lámparas infrarrojas algunos modelos Reemplazo de las bombillas halógenasPage Service Parts & AccessoriesPièces et Accessoires Entretien
Related manuals
Manual 38 pages 59.84 Kb

PH36GS, PH30HS, PH36HS, PH42GS, PH48GS specifications

The Thermador PH54GS, PH48HS, PH48GS, PH42GS, and PH36HS are a distinguished range of built-in refrigeration solutions, seamlessly combining style, efficiency, and advanced technology to enhance any kitchen environment. Each model in this collection is designed to provide optimal food preservation while offering a variety of features that cater to the needs of modern culinary enthusiasts.

The Thermador PH54GS features a spacious 54-inch design that offers ample storage space for all your cooling needs. It boasts a top-of-the-line cooling system that maintains consistent temperatures, ensuring fresh food for longer periods. The model incorporates a sleek stainless-steel finish that adds elegance to any kitchen. Furthermore, advanced magnetic door seals help retain cold air, leading to energy efficiency.

The PH48HS is another stunning model that measures 48 inches. It comes equipped with the innovative Cool Air Flow system, providing even airflow and temperature distribution throughout the interior. This model also features a unique Dual Compressor system that minimizes temperature fluctuations, keeping food fresher longer. Additionally, LED lighting illuminates the interior, allowing for easy visibility and a premium look.

Moving to the PH48GS, this 48-inch unit champions flexibility with adjustable shelving and various storage compartments. Its high-quality glass shelves can hold heavy items while allowing bright LED lights to shine through, enhancing visibility. The unit is also equipped with a filtered water dispenser, ensuring clean drinking water is readily available.

The PH42GS, a 42-inch option, offers similar features with a focus on convenience. Its integrated ice maker supplies a steady stream of fresh ice, perfect for entertaining or daily hydration. The model also boasts a sophisticated touchscreen control panel that allows users to personalize their cooling settings with ease.

Lastly, the PH36HS is a compact yet powerful 36-inch refrigeration solution. Its sleek design and smart storage solutions, like adjustable bins, make it ideal for smaller kitchens without compromising on functionality. This model also emphasizes energy savings, designed with insulation that minimizes energy loss.

In conclusion, the Thermador PH series is an exceptional choice for discerning homeowners seeking stylish, efficient refrigeration. With innovative technologies, ample storage, and customizable options, these models redefine luxury and functionality in the kitchen.
Top Page Image Contents