GE ZICP720 Tools Required, Hardware Supplied, Trim Supplied, Materials Required, Flooring

Page 6

Installation Instructions

TOOLS REQUIRED

•Tinsnips to cut banding

•Stepladder

•Bucket

•Level

•Appliance dolly

•Tubing cutter

•7/16″ open-end wrench

•#2 Phillips screwdriver

•Drill and appropriate bits

•5/16″, 7/16″ socket

•Safety glasses

•1-1/4″and 1/2″ open-ended wrench

•Pliers

•1/4″ ratchet or 1/4″ angled wrench

•Tape measure

HARDWARE SUPPLIED

•Water filter bypass plug

•Anti-Tip brackets

•1/4″ nut and ferrule

TRIM SUPPLIED

A.Top trim

B.Left inside case trim

C.Right inside case trim

D.Center U-shape trim

E.Grille base wrap

F.Grille panel

G.Toekick

H.Foam spacer pads

I.Phillips screws (34)

J.Package of 12 plastic spacers

K.Flat metal bracket

L.2 Large screws (for metal bracket)

M.2 Corner trim brackets

MATERIALS REQUIRED

•71″ long 2x4 for Anti-Tip support

•1/4″ copper water line tubing or two GE SmartConnect™ Refrigerator Tubing kits

•Two water shut-off valves

•Screws to secure refrigerator to cabinetry

•Stick-on hook and loop fastener strips for 1/4″ side panels

FLOORING

For proper installation, this refrigerator must be placed on a level surface of hard material that is at the same height as the rest of the flooring. This surface should be strong enough to support a fully loaded refrigerator, or approximately 2,400 lbs.

NOTE: Protect the finish of the flooring. Cut a large section of the cardboard carton and place under the refrigerator where you are working.

A

B

D C

E

F

G

H

K

I

L

J

M

GROUNDING THE REFRIGERATOR

IMPORTANT—(Please read carefully)

FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED.

The power cord of this appliance is equipped with a 3-prong (grounding) plug which mates with a standard three-prong (grounding) wall receptacle to minimize the possibility of electric shock hazard from this appliance.

Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded.

Where a standard 2-prong wall outlet is encountered, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet.

DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR REMOVE THE THIRD (GROUND) PRONG FROM THE POWER CORD.

DO NOT USE AN ADAPTER PLUG TO CONNECT THE REFRIGERATOR TO A 2-PRONG OUTLET.

DO NOT USE AN EXTENSION CORD WITH THIS APPLIANCE.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Installation Instructions Contents Before YOU BeginInstallation Space Dimensions and Clearances Filler strips to prevent interference with Frameless Cabinets The case trimOverlaps cabinets at the top and sides Cabinet door swing. The opening mustDoor Swing optional setting Scale Trim Supplied Tools RequiredHardware Supplied Materials RequiredInstall Water Lines Remove PackagingShut off the main water supply Install NEW Side Trim Install Side PanelsSkip this step if you are not using side panels Install ANTI-TIP Brackets Brackets Required BlockReceptacles. Reach into the top opening Push Refrigerator Into OpeningPlace a level inside the machine for each unit Level the RefrigeratorsBracket Drawers should be evenly alignedTWO People are Required to Install Grille Panel Alternate ANTI-TIP ProcedureInstall Grille Panel Secure Refrigerator to CabinetryInstall Center Trim Strip Adjust Door SwingCheck and Correct Door Alignment Close the grille panel and both doorsSkip this Step if Doors are Level Determine Correct Spacer RH Door Install Dim. a LH Spacer RH SpacerLH Door Install Dim. a LH Spacer RH Spacer RH Fresh Food door is higher than the LH doorRemove Pin Screws Copper Tubing Install Grille Base WrapConnect Water Supply GE SmartConnect TubingConnect Power Install ToekickStart Icemaker Page GE Consumer & Industrial
Top Page Image Contents