GE 200D26000P022 installation instructions Care and cleaning of the refrigerator, Installation

Page 13

 

 

www.GEAppliances.com

 

 

 

Models without a shelf

Removing and Replacing the Ice

Models with a shelf

above the ice bin

Storage Bin on Dispenser Models

above the ice bin

To remove:

 

To remove:

Safety

Lift the bin, then pull it forward until the bin stops.

There are two types of ice storage bins on dispenser models. One has a shelf above the bin, the other does not.

Always set the icemaker power switch to the O (off) position before removing the ice bin.

When replacing either type of ice bin:

Always be sure to press it firmly into place. If it does not go all the way back, remove it and rotate the drive mechanism 1/4 turn. Then push the bin back again.

Rotate

Pull the bin straight out, then lift past the stop position.

Instructions Operating Instructions

Drive

Lift and pull forward againMechanism to remove the bin.

Care and cleaning of the refrigerator.

Installation

Dispenser drip area.

Cleaning the Outside

The dispenser drip area (on some models), beneath the grille, should be wiped dry. Water left in this area may leave deposits. Remove the deposits by adding undiluted vinegar to the well. Soak until the deposits disappear or become loose enough to rinse away.

The dispenser cradle (on some models). Before cleaning, lock the dispenser by pressing and holding the LOCK CONTROL pad for 3 seconds. Clean with warm water and baking soda solution – about a tablespoon (15 ml) of baking soda to

a quart (1 liter) of water. Rinse thoroughly and wipe dry.

The door handles and trim. Clean with a cloth dampened with soapy water. Dry with a soft cloth.

Keep the outside clean. Wipe with a clean cloth lightly dampened with kitchen appliance wax or mild liquid dish detergent. Dry and polish with a clean, soft cloth.

Do not wipe the refrigerator with a soiled dish cloth or wet towel. These may leave a residue that can erode the paint. Do not use scouring pads, powdered cleaners, bleach or cleaners containing bleach because these products can scratch and weaken the paint finish.

Instructions Troubleshooting Tips

Cleaning the Inside

To help prevent odors, leave an open box of baking soda in the fresh food and freezer compartments.

Unplug the refrigerator before cleaning. If this is not practical, wring excess moisture out of sponge or cloth when cleaning around switches, lights or controls.

Use warm water and baking soda solution – about a tablespoon (15 ml) of baking soda to a quart (1 liter) of water. This both cleans and neutralizes odors. Rinse and wipe dry.

Use of any cleaning solution other than that which is recommended, especially those that contain petroleum distillates, can crack or damage the interior of the refrigerator.

Avoid cleaning cold glass shelves with hot water because the extreme temperature difference may cause them to break. Handle glass shelves carefully. Bumping tempered glass can cause

it to shatter.

Do not wash any plastic refrigerator parts in the

dishwasher.

13

Consumer Support

Image 13
Contents Serial # Side by SideSafety Precautions Before You Throw Away Your Old Refrigerator or Freezer Operating InstructionsRefrigerants Instructions Operating Instructions HOW to Connect ElectricityTroubleshooting Tips Consumer Support About the temperature controlsHow to Use About TurboCool on some modelsInstalling the Filter Cartridge When to Replace the FilterAbout the water filter on some models Water Filter CartridgeRefrigerator Door Bins and Freezer Door Tilt-Out Bins About the shelves and binsSlide-Out Spillproof Shelf Freezer Baskets QuickSpace Shelf on some modelsSlide-Out Freezer Shelves Fixed Freezer ShelvesAbout the refrigerator doors SafetyRefrigerator Doors Door AlignmentAbout the crispers and pans Consumer Support Troubleshooting TipsAbout crisper removal Automatic Icemaker About the automatic icemakerAbout the ice and water dispenser on some models Consumer Support TroubleshootingInstallation Care and cleaning of the refrigeratorBehind the Refrigerator Consumer Support Troubleshooting Tips InstallationPreparing for Vacation Preparing to MoveInstructions Operating Replacing the light bulbsPreparation Before YOU BeginTools YOU will Need Remove the Base Grille Moving the RefrigeratorRemove the Freezer Door Disconnect the Power Coupling on some modelsRemove the Refrigerator Door However, please note the following Replacing the DoorsClearances Refrigerator LocationPlug in the Refrigerator Turn on the Water SupplyLevel the Doors Level the RefrigeratorStart the Icemaker Replace the Base GrilleSET the Controls What YOU will Need Choose the Valve Location Shut OFF the Main Water SupplyDrill the Hole for the Valve Connect the Tubing To the Valve Fasten the Shutoff ValveTighten the Pipe Clamp Route the TubingHummm Normal operating soundsBefore you call for service… Ice cubes have See Care and cleaningOdor/taste Small or hollow cubesNo water or ice cube Temperatures are OKProduction But Crushed ICEConsumer Warranty What GE Will Not Cover GE Will ReplaceOne Year Thirty DaysOperating Specifications Performance Data SheetGeneral Installation/Operation/Maintenance Requirements Special NoticesWater Treatment Device Certificate Number Troubleshooting Tips Installation Instructions Operating Instructions Safety InstructionsWe’ll Cover Any Appliance. Anywhere. Anytime Consumer Product Ownership Registration Page Consumer Support GE Appliances Website Schedule Service

200D26000P022 specifications

The GE 200D26000P022 is a highly advanced and versatile industrial motor designed by General Electric for various heavy-duty applications. Known for its robust performance and durability, this motor is integral to many manufacturing and processing environments.

One of the primary features of the GE 200D26000P022 is its impressive power output, making it suitable for demanding applications that require high torque and efficiency. The motor operates on a high voltage, which allows for significant energy savings and improved operational efficiency. Its design includes a host of advanced engineering features that enhance its performance, including higher speed ratings and excellent thermal management.

Incorporating state-of-the-art technologies, the GE 200D26000P022 integrates permanent magnet motor technology, which enhances its efficiency compared to traditional induction motors. This results in lower energy consumption, reducing operating costs and minimizing the environmental impact. The motor's design also emphasizes minimal maintenance requirements, allowing users to enjoy extended service life with reduced downtime.

Another notable characteristic of the GE 200D26000P022 is its adaptability. This motor can seamlessly be integrated into various applications, including pumps, compressors, and conveyors. Its ability to function in diverse environments, including those with harsh conditions, is a testament to its robust engineering design. The motor is constructed with high-quality materials that provide resistance to corrosion, heat, and mechanical stress.

Additionally, the GE 200D26000P022 is equipped with advanced control systems. These systems allow for precise speed and torque management, enhancing overall operational efficiency. The motor can be controlled using various protocols, making it compatible with numerous industrial automation frameworks. This feature facilitates easier integration into modern smart factories and automation solutions.

In summary, the GE 200D26000P022 stands out for its powerful performance, energy efficiency, and versatility. Its innovative technologies and robust characteristics make it an ideal choice for industries seeking reliable motor solutions capable of handling heavy loads and demanding conditions. As a result, it continues to be a preferred option for professionals in the industrial sector looking to enhance their operations.