GE 200D26000P022 Shut OFF the Main Water Supply, Choose the Valve Location

Page 26

Installation Instructions

INSTALLING THE WATER LINE (CONT.)

WHAT YOU WILL NEED (CONT.)

NOTE: The only GE approved plastic tubing is that supplied in GE SmartConnect™ Refrigerator Tubing kits. Do not use any other plastic water supply line because the line is under pressure at all times. Certain types of plastic will crack or rupture with age and cause water damage to your home.

•A GE water supply kit (containing tubing, shutoff valve and fittings listed below) is available at extra cost from your dealer or from Parts and Accessories, 800.626.2002 (in Canada 1.888.261.3055).

•A cold water supply. The water pressure must be between 20 and 120 p.s.i. (1.4–8.1 bar).

•Power drill.

•1/2″ or adjustable wrench.

•Straight and Phillips blade screwdriver.

•Two 1/4 ″ outer diameter compression nuts and 2 ferrules (sleeves)—to connect the copper tubing to the shutoff valve and the refrigerator water valve.

OR

•If you are using a GE SmartConnect™ Refrigerator Tubing kit, the necessary fittings are preassembled to the tubing.

•If your existing copper water line has a flared fitting at the end, you will need an adapter (available at plumbing supply stores) to connect the water line to the refrigerator OR you can cut off the flared fitting with a tube cutter and then use a compression fitting. Do not cut formed end from GE SmartConnect™ Refrigerator tubing.

•Shutoff valve to connect to the cold water line. The shutoff valve should have a water

inlet with a minimum inside diameter of 5/32″ at the point of connection to the COLD WATER LINE. Saddle-type shutoff valves are included in many water supply kits. Before purchasing, make sure a saddle-type valve complies with your local plumbing codes.

Install the shutoff valve on the nearest frequently used drinking water line.

1SHUT OFF THE MAIN WATER SUPPLY

Turn on the nearest faucet long enough to clear the line of water.

2CHOOSE THE VALVE LOCATION

Choose a location for the valve that is easily accessible. It is best to connect into the side of a vertical water pipe. When it is necessary to connect into a horizontal water pipe, make the connection to the top or side, rather than at the bottom,

to avoid drawing off any sediment from the water pipe.

3DRILL THE HOLE FOR THE VALVE

Drill a 1/4″ hole in the water pipe (even if using a self-piercing valve), using a sharp bit. Remove any burrs resulting from drilling the hole in the pipe.

Take care not to allow water to drain into the drill.

Failure to drill a 1/4″ hole may result in reduced ice production or smaller cubes.

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Side by Side Serial #Safety Precautions Refrigerants Operating InstructionsBefore You Throw Away Your Old Refrigerator or Freezer HOW to Connect Electricity Instructions Operating InstructionsHow to Use About the temperature controlsTroubleshooting Tips Consumer Support About TurboCool on some modelsAbout the water filter on some models When to Replace the FilterInstalling the Filter Cartridge Water Filter CartridgeSlide-Out Spillproof Shelf About the shelves and binsRefrigerator Door Bins and Freezer Door Tilt-Out Bins Slide-Out Freezer Shelves QuickSpace Shelf on some modelsFreezer Baskets Fixed Freezer ShelvesRefrigerator Doors SafetyAbout the refrigerator doors Door AlignmentAbout crisper removal Consumer Support Troubleshooting TipsAbout the crispers and pans About the automatic icemaker Automatic IcemakerConsumer Support Troubleshooting About the ice and water dispenser on some modelsCare and cleaning of the refrigerator InstallationPreparing for Vacation Consumer Support Troubleshooting Tips InstallationBehind the Refrigerator Preparing to MoveReplacing the light bulbs Instructions OperatingTools YOU will Need Before YOU BeginPreparation Moving the Refrigerator Remove the Base GrilleDisconnect the Power Coupling on some models Remove the Freezer DoorRemove the Refrigerator Door Replacing the Doors However, please note the followingRefrigerator Location ClearancesTurn on the Water Supply Plug in the RefrigeratorLevel the Refrigerator Level the DoorsSET the Controls Replace the Base GrilleStart the Icemaker What YOU will Need Drill the Hole for the Valve Shut OFF the Main Water SupplyChoose the Valve Location Tighten the Pipe Clamp Fasten the Shutoff ValveConnect the Tubing To the Valve Route the TubingNormal operating sounds HummmBefore you call for service… Odor/taste See Care and cleaningIce cubes have Small or hollow cubesProduction Temperatures are OKNo water or ice cube But Crushed ICEConsumer Warranty One Year GE Will ReplaceWhat GE Will Not Cover Thirty DaysGeneral Installation/Operation/Maintenance Requirements Performance Data SheetOperating Specifications Special NoticesWater Treatment Device Certificate Number Operating Instructions Safety Instructions Troubleshooting Tips Installation InstructionsWe’ll Cover Any Appliance. Anywhere. Anytime Consumer Product Ownership Registration Page GE Appliances Website Schedule Service Consumer Support

200D26000P022 specifications

The GE 200D26000P022 is a highly advanced and versatile industrial motor designed by General Electric for various heavy-duty applications. Known for its robust performance and durability, this motor is integral to many manufacturing and processing environments.

One of the primary features of the GE 200D26000P022 is its impressive power output, making it suitable for demanding applications that require high torque and efficiency. The motor operates on a high voltage, which allows for significant energy savings and improved operational efficiency. Its design includes a host of advanced engineering features that enhance its performance, including higher speed ratings and excellent thermal management.

Incorporating state-of-the-art technologies, the GE 200D26000P022 integrates permanent magnet motor technology, which enhances its efficiency compared to traditional induction motors. This results in lower energy consumption, reducing operating costs and minimizing the environmental impact. The motor's design also emphasizes minimal maintenance requirements, allowing users to enjoy extended service life with reduced downtime.

Another notable characteristic of the GE 200D26000P022 is its adaptability. This motor can seamlessly be integrated into various applications, including pumps, compressors, and conveyors. Its ability to function in diverse environments, including those with harsh conditions, is a testament to its robust engineering design. The motor is constructed with high-quality materials that provide resistance to corrosion, heat, and mechanical stress.

Additionally, the GE 200D26000P022 is equipped with advanced control systems. These systems allow for precise speed and torque management, enhancing overall operational efficiency. The motor can be controlled using various protocols, making it compatible with numerous industrial automation frameworks. This feature facilitates easier integration into modern smart factories and automation solutions.

In summary, the GE 200D26000P022 stands out for its powerful performance, energy efficiency, and versatility. Its innovative technologies and robust characteristics make it an ideal choice for industries seeking reliable motor solutions capable of handling heavy loads and demanding conditions. As a result, it continues to be a preferred option for professionals in the industrial sector looking to enhance their operations.
Top Page Image Contents