GE 200D26000P022 About the temperature controls, About TurboCool on some models, How it Works

Page 5

About the temperature controls.

www.GEAppliances.com

ADJUST FREEZER TEMP

ADJUST REFRIGERATOR TEMP

COLDER

WARMER

COLDER

WARMER

 

9 IS COLDEST

 

9 IS COLDEST

The temperature controls are preset in the factory at 5 for both the refrigerator and freezer compartments. Allow 24 hours for the temperature to stabilize to the preset recommended settings.

Several adjustments may be required. Adjust the controls one increment at a time, and allow 24 hours after each adjustment for the refrigerator to reach the setting you have selected.

Setting either or both controls to 0 stops cooling in both the freezer and refrigerator compartments, but does not shut off electrical power to the refrigerator.

Control settings will vary based on personal preferences, usage and operating conditions and may require more than one adjustment.

NOTE: The refrigerator is shipped with protective film covering the temperature controls. If this film was not removed during installation, remove it now.

About TurboCool™ (on some models).

Safety Instructions Operating Instructions Installation Instructions

How it Works

TurboCool rapidly cools the refrigerator compartment in order to more quickly cool foods. Use TurboCool when adding a large amount of food to the refrigerator compartment, putting away foods after they have been sitting out at room temperature or when putting away warm leftovers. It can also be used if the refrigerator has been without power for an extended period.

Once activated, the compressor will turn on immediately and the fans will cycle on and off at high speed as needed for eight hours. The compressor will continue to run until the refrigerator compartment cools to approximately 34°F (1°C), then it will cycle on and off to maintain this setting. After 8 hours, or if TurboCool is pressed again, the refrigerator compartment will return to the original setting.

How to Use

Press TurboCool. The TurboCool indicator light will come on; however, the refrigerator temperature display will still show the current setting.

After TurboCool is complete, the TurboCool indicator light will go out.

NOTES: The refrigerator temperature cannot be changed during TurboCool.

The freezer temperature is not affected during TurboCool.

When opening the refrigerator door during TurboCool, the fans will continue to run if they have cycled on.

Troubleshooting Tips Consumer Support

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Serial # Side by SideSafety Precautions Refrigerants Operating InstructionsBefore You Throw Away Your Old Refrigerator or Freezer Instructions Operating Instructions HOW to Connect ElectricityTroubleshooting Tips Consumer Support About the temperature controlsHow to Use About TurboCool on some modelsInstalling the Filter Cartridge When to Replace the FilterAbout the water filter on some models Water Filter CartridgeSlide-Out Spillproof Shelf About the shelves and binsRefrigerator Door Bins and Freezer Door Tilt-Out Bins Freezer Baskets QuickSpace Shelf on some modelsSlide-Out Freezer Shelves Fixed Freezer ShelvesAbout the refrigerator doors SafetyRefrigerator Doors Door AlignmentAbout crisper removal Consumer Support Troubleshooting TipsAbout the crispers and pans Automatic Icemaker About the automatic icemakerAbout the ice and water dispenser on some models Consumer Support TroubleshootingInstallation Care and cleaning of the refrigeratorBehind the Refrigerator Consumer Support Troubleshooting Tips InstallationPreparing for Vacation Preparing to MoveInstructions Operating Replacing the light bulbsTools YOU will Need Before YOU BeginPreparation Remove the Base Grille Moving the RefrigeratorRemove the Freezer Door Disconnect the Power Coupling on some modelsRemove the Refrigerator Door However, please note the following Replacing the DoorsClearances Refrigerator LocationPlug in the Refrigerator Turn on the Water SupplyLevel the Doors Level the RefrigeratorSET the Controls Replace the Base GrilleStart the Icemaker What YOU will Need Drill the Hole for the Valve Shut OFF the Main Water SupplyChoose the Valve Location Connect the Tubing To the Valve Fasten the Shutoff ValveTighten the Pipe Clamp Route the TubingHummm Normal operating soundsBefore you call for service… Ice cubes have See Care and cleaningOdor/taste Small or hollow cubesNo water or ice cube Temperatures are OKProduction But Crushed ICEConsumer Warranty What GE Will Not Cover GE Will ReplaceOne Year Thirty DaysOperating Specifications Performance Data SheetGeneral Installation/Operation/Maintenance Requirements Special NoticesWater Treatment Device Certificate Number Troubleshooting Tips Installation Instructions Operating Instructions Safety InstructionsWe’ll Cover Any Appliance. Anywhere. Anytime Consumer Product Ownership Registration Page Consumer Support GE Appliances Website Schedule Service

200D26000P022 specifications

The GE 200D26000P022 is a highly advanced and versatile industrial motor designed by General Electric for various heavy-duty applications. Known for its robust performance and durability, this motor is integral to many manufacturing and processing environments.

One of the primary features of the GE 200D26000P022 is its impressive power output, making it suitable for demanding applications that require high torque and efficiency. The motor operates on a high voltage, which allows for significant energy savings and improved operational efficiency. Its design includes a host of advanced engineering features that enhance its performance, including higher speed ratings and excellent thermal management.

Incorporating state-of-the-art technologies, the GE 200D26000P022 integrates permanent magnet motor technology, which enhances its efficiency compared to traditional induction motors. This results in lower energy consumption, reducing operating costs and minimizing the environmental impact. The motor's design also emphasizes minimal maintenance requirements, allowing users to enjoy extended service life with reduced downtime.

Another notable characteristic of the GE 200D26000P022 is its adaptability. This motor can seamlessly be integrated into various applications, including pumps, compressors, and conveyors. Its ability to function in diverse environments, including those with harsh conditions, is a testament to its robust engineering design. The motor is constructed with high-quality materials that provide resistance to corrosion, heat, and mechanical stress.

Additionally, the GE 200D26000P022 is equipped with advanced control systems. These systems allow for precise speed and torque management, enhancing overall operational efficiency. The motor can be controlled using various protocols, making it compatible with numerous industrial automation frameworks. This feature facilitates easier integration into modern smart factories and automation solutions.

In summary, the GE 200D26000P022 stands out for its powerful performance, energy efficiency, and versatility. Its innovative technologies and robust characteristics make it an ideal choice for industries seeking reliable motor solutions capable of handling heavy loads and demanding conditions. As a result, it continues to be a preferred option for professionals in the industrial sector looking to enhance their operations.
Top Page Image Contents