GE 200D26000P022 installation instructions What YOU will Need

Page 25

Installation Instructions

INSTALLING THE WATER LINE (ICEMAKER & DISPENSER MODELS)

BEFORE YOU BEGIN

Recommended copper water supply kits are WX8X2, WX8X3 or WX8X4, depending on the amount of tubing you need. Approved plastic water supply lines are GE SmartConnect™ Refrigerator Tubing (WX08X10002, WX08X10006, WX08X10015 and WX08X10025).

When connecting your refrigerator to a GE Reverse Osmosis Water System, the only approved installation is with a GE RVKit. For other reverse osmosis water systems, follow the manufacturer’s recommendations.

If the water supply to the refrigerator is from a Reverse Osmosis Water Filtration System AND the refrigerator also has a water filter, use the refrigerator’s filter bypass plug. Using the refrigerator’s water filtration cartridge in conjunction with the RO filter can result in hollow ice cubes and slower water flow from the water dispenser.

This water line installation is not warranted by the refrigerator or icemaker manufacturer. Follow these instructions carefully to minimize the risk of expensive water damage. Water hammer (water banging in the pipes) in house plumbing can cause damage to refrigerator parts and lead to water leakage or flooding. Call a qualified plumber to correct water hammer before installing the water supply line to the refrigerator.

To prevent burns and product damage, do not hook up the water line to the hot water line. If you use your refrigerator before connecting the water line, make sure the icemaker power switch is in the O (off) position.

Do not install the icemaker tubing in areas where temperatures fall below freezing. When using any electrical device (such as a power drill) during installation, be sure the device is double insulated or grounded in a manner to prevent the hazard of electric shock, or is battery powered.

All installations must be in accordance with local plumbing code requirements.

WHAT YOU WILL NEED

•Copper or GE SmartConnect™ Refrigerator Tubing kit, 1/4″ outer diameter to connect the refrigerator to the water supply. If using copper, be sure both ends of the tubing are cut square.

To determine how much tubing you need: measure the distance from the water valve on the back of the refrigerator to the water supply pipe. Then add 8′ (2.4 m). Be sure there is sufficient extra tubing (about 8′ [2.4 m] coiled into 3 turns of about 10″ [25 cm] diameter) to allow the refrigerator to move out from the wall after installation.

GE SmartConnect™ Refrigerator Tubing Kits are available in the following lengths:

2′ (0.6 m) – WX08X10002

6′ (1.8 m) – WX08X10006

15′ (4.6 m) – WX08X10015

25′ (7.6 m) – WX08X10025

Be sure that the kit you select allows at least 8′ (2.4 m) as described above.

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Serial # Side by SideSafety Precautions Before You Throw Away Your Old Refrigerator or Freezer Operating InstructionsRefrigerants Instructions Operating Instructions HOW to Connect ElectricityTroubleshooting Tips Consumer Support About the temperature controlsHow to Use About TurboCool on some modelsInstalling the Filter Cartridge When to Replace the FilterAbout the water filter on some models Water Filter CartridgeRefrigerator Door Bins and Freezer Door Tilt-Out Bins About the shelves and binsSlide-Out Spillproof Shelf Freezer Baskets QuickSpace Shelf on some modelsSlide-Out Freezer Shelves Fixed Freezer ShelvesAbout the refrigerator doors SafetyRefrigerator Doors Door AlignmentAbout the crispers and pans Consumer Support Troubleshooting TipsAbout crisper removal Automatic Icemaker About the automatic icemakerAbout the ice and water dispenser on some models Consumer Support TroubleshootingInstallation Care and cleaning of the refrigeratorBehind the Refrigerator Consumer Support Troubleshooting Tips InstallationPreparing for Vacation Preparing to MoveInstructions Operating Replacing the light bulbsPreparation Before YOU BeginTools YOU will Need Remove the Base Grille Moving the RefrigeratorRemove the Freezer Door Disconnect the Power Coupling on some modelsRemove the Refrigerator Door However, please note the following Replacing the DoorsClearances Refrigerator LocationPlug in the Refrigerator Turn on the Water SupplyLevel the Doors Level the RefrigeratorStart the Icemaker Replace the Base GrilleSET the Controls What YOU will Need Choose the Valve Location Shut OFF the Main Water SupplyDrill the Hole for the Valve Connect the Tubing To the Valve Fasten the Shutoff ValveTighten the Pipe Clamp Route the TubingHummm Normal operating soundsBefore you call for service… Ice cubes have See Care and cleaningOdor/taste Small or hollow cubesNo water or ice cube Temperatures are OKProduction But Crushed ICEConsumer Warranty What GE Will Not Cover GE Will ReplaceOne Year Thirty DaysOperating Specifications Performance Data SheetGeneral Installation/Operation/Maintenance Requirements Special NoticesWater Treatment Device Certificate Number Troubleshooting Tips Installation Instructions Operating Instructions Safety InstructionsWe’ll Cover Any Appliance. Anywhere. Anytime Consumer Product Ownership Registration Page Consumer Support GE Appliances Website Schedule Service

200D26000P022 specifications

The GE 200D26000P022 is a highly advanced and versatile industrial motor designed by General Electric for various heavy-duty applications. Known for its robust performance and durability, this motor is integral to many manufacturing and processing environments.

One of the primary features of the GE 200D26000P022 is its impressive power output, making it suitable for demanding applications that require high torque and efficiency. The motor operates on a high voltage, which allows for significant energy savings and improved operational efficiency. Its design includes a host of advanced engineering features that enhance its performance, including higher speed ratings and excellent thermal management.

Incorporating state-of-the-art technologies, the GE 200D26000P022 integrates permanent magnet motor technology, which enhances its efficiency compared to traditional induction motors. This results in lower energy consumption, reducing operating costs and minimizing the environmental impact. The motor's design also emphasizes minimal maintenance requirements, allowing users to enjoy extended service life with reduced downtime.

Another notable characteristic of the GE 200D26000P022 is its adaptability. This motor can seamlessly be integrated into various applications, including pumps, compressors, and conveyors. Its ability to function in diverse environments, including those with harsh conditions, is a testament to its robust engineering design. The motor is constructed with high-quality materials that provide resistance to corrosion, heat, and mechanical stress.

Additionally, the GE 200D26000P022 is equipped with advanced control systems. These systems allow for precise speed and torque management, enhancing overall operational efficiency. The motor can be controlled using various protocols, making it compatible with numerous industrial automation frameworks. This feature facilitates easier integration into modern smart factories and automation solutions.

In summary, the GE 200D26000P022 stands out for its powerful performance, energy efficiency, and versatility. Its innovative technologies and robust characteristics make it an ideal choice for industries seeking reliable motor solutions capable of handling heavy loads and demanding conditions. As a result, it continues to be a preferred option for professionals in the industrial sector looking to enhance their operations.
Top Page Image Contents