GE 200D9366P004 Cont, Turn on the Water Supply, Plug in the Refrigerator, Level the Refrigerator

Page 16

Installation Instructions

INSTALLING THE REFRIGERATOR (cont.)

1CONNECTING THE REFRIGERATOR TO THE HOUSE WATER LINE

(cont.)

AIf you are using copper tubing, place a compression nut and ferrule (sleeve) onto the end of the tubing coming from the house cold water supply.

If you are using the GE SmartConnect™ tubing, the nuts are already assembled to the tubing.

BIf you are using copper tubing, insert the end of the tubing into the refrigerator connection, at the back of the refrigerator, as far as possible. While holding the tubing, tighten the fitting.

If you are using GE SmartConnect™ tubing, insert the molded end of the tubing into the refrigerator connection, at the back of the refrigerator, and tighten the compression nut until it is hand tight . Then tighten one additional turn with a wrench. Overtightening may cause leaks.

CFasten the tubing into the clamp provided to hold it in position. You may need to pry open the clamp.

One of the illustrations below will look like the connection on your refrigerator.

Icemaker-Ready models

Tubing

1/4″ Copper

Tubing

Clamp

 

1/4″ Compression Nut

Ferrule (sleeve)

Refrigerator

ConnectionSmartConnect™

Tubing

Icemaker-Installed Models

Ferrule 1/4″

Refrigerator (sleeve) Compression

Connection Nut

SmartConnect™

Tubing

1/4″ Tubing

Tubing Clamp

16

2TURN ON THE WATER SUPPLY

(icemaker models)

Turn the water on at the shutoff valve (house water supply) and check for any leaks.

3PLUG IN THE REFRIGERATOR

On models with an icemaker, before plugging in the refrigerator, make sure the icemaker power switch is set to the O (off) position.

See the grounding information attached to the power cord.

4PUT THEREFRIGERATOR IN PLACE

Move the refrigerator to its final location.

5LEVEL THE REFRIGERATOR

Adjustable legs at the front corners of the refrigerator should be set so the refrigerator is firmly positioned on the floor, and the front is raised just enough that the door closes easily when opened about halfway.

To adjust the leveling legs, turn the legs clockwise to raise the refrigerator, counterclockwise to lower it .

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Ge.com Write the model and serial numbers here Model # Serial #Before You Throw Away Your Old Refrigerator or FreezerHOW to Connect Electricity Ge.comAbout the controls with temperature settings When to Replace the Filter Installing the Filter CartridgeAbout the water filter. on some models Water Filter CartridgeNon-Adjustable Shelves on the Door on some models About the shelves and binsRearranging the Shelves To removeAbout the crispers and pans Adjustable Humidity Crisper on some modelsFruit and Vegetable Crisper When replacing the deep full-width basket About the freezer drawer. on some modelsFreezer Shelves and Baskets Basket RemovalNon-Adjustable Shelf on Freezer Door About the freezer compartment. on some modelsFreezer Shelf and Basket Fixed Shelf RemovalIcemaker Accessory Kit To reach the icemaker power switch, pullAbout the automatic icemaker. on some models Automatic IcemakerCleaning the Outside Care and cleaning of the refrigeratorCleaning the Inside Preparing for Vacation Behind the RefrigeratorPreparing to Move Refrigerator Lights Replacing the light bulbsFreezer Light Before YOU Begin PreparationTools YOU MAY Need Moving the Refrigerator IndoorsConnecting the Refrigerator to the House Water Line Refrigerator LocationClearances Removetop CAP cont. on some modelsCont Turn on the Water SupplyPlug in the Refrigerator PUT Therefrigerator in PlaceRemove the Fresh Food Door Handle Remove the FreezerdoorhandleAttach the Fresh Food Door Handle Attach the FreezerdoorhandleSET the Controls Leveling legs have 2 purposesRemovethebasket RemovethedrawerfrontRemovethedrawerfront Remove the Base GrilleReplace the Freezer Basket Attachand Securethedrawer Front TotheslidesReversingthedoorswing Single Door Refrigerator Models only Important NotesTools YOU will Need Removethe Refrigerator DoorTransfer Center Hinge Bracket Remove the Freezer DoorRemove Bottom Hinge and Leveling LEG Rehangfreezerdoor Transfer Refrigerator Doorhandle TorightRehangrefrigeratordoor Install the Logo BadgeDouble Door Refrigerator Models only Removing the Doors Double Door Refrigerator Models only Removetherefrigerator DoorsRemovecenterhinge Removeopposite DoorInstall Centerhinge RehangrefrigeratordoorsReplaceopposite Door Align Double DoorsInstalling the Water Line Icemaker Models What YOU will NeedChoose the Valve Location Shut OFF the Main Water SupplyDrill the Hole for the Valve Fasten the Shutoff Valve Connect the Tubing to the ValveTighten the Pipe Clamp Route the TubingBefore you call for service… Normal operating soundsConsumer Support Troubleshooting Tips See About the controlsSee Replacing the light bulbs Handle is loose Handle needs adjusting Should be positioned verticallyGE Service Protection Plus Warranty Registration Department Box Louisville, KYConsumer Product Ownership Registration Model NumberOwnership Registration Page GE Will Replace What GE Will Not CoverGE and Geprofilemodels One Year Thirty DaysWhat is not Covered Terms and ConditionsPerformance Data Sheet Operating SpecificationsGeneral Installation/Operation/Maintenance Requirements Special NoticesWater Treatment Device

200D9366P004 specifications

The GE 200D9366P004 is a high-performance component designed for various industrial applications, particularly in power generation and distribution systems. This device is a part of General Electric’s extensive lineup of electrical components, renowned for their durability and operational efficiency.

One of the main features of the GE 200D9366P004 is its robust design capacity, built to handle significant electrical loads while maintaining stability and safety. The component is engineered to comply with rigorous industry standards, ensuring not only reliability but also longevity in harsh operational environments. This makes it suitable for a range of applications, from power plants to critical infrastructure systems.

In terms of technologies, the GE 200D9366P004 incorporates advanced electric and electronic control systems that enhance its operational capabilities. This includes state-of-the-art monitoring technologies that provide real-time data on performance metrics, allowing for prompt detection of anomalies and facilitating proactive maintenance strategies. This predictive capability is crucial in minimizing downtime and extending the lifecycle of the equipment.

The operating characteristics of the GE 200D9366P004 are particularly noteworthy. It is designed for optimal thermal performance, ensuring that heat dissipation is managed efficiently. This helps in maintaining consistent performance even under high operational loads. Additionally, the component features advanced insulating materials that contribute to its reliability and efficiency, reducing the risks associated with electrical failures.

Another notable characteristic is its modular design, which simplifies installation and maintenance processes. This modularity allows for easier upgrades and repairs, making it a flexible choice for many organizations looking to enhance their operational efficiency without extensive downtime.

Overall, the GE 200D9366P004 stands out in the industrial landscape for its combination of advanced technology, rugged reliability, and operational efficiency. Whether utilized in power generation, industrial automation, or management of critical electrical infrastructure, this component exemplifies GE’s commitment to quality and innovation in electrical solutions, making it a preferred choice for professionals aiming to achieve high-performance standards in their operations.
Top Page Image Contents