GE 200D9366P004 Installing the Water Line Icemaker Models, What YOU will Need

Page 28

Installation Instructions

INSTALLING THE WATER LINE (ICEMAKER MODELS)

BEFORE YOU BEGIN

Recommended copper water supply kits are WX8X2, WX8X3 or WX8X4, depending on the amount of tubing you need. Approved plastic water supply lines are GE SmartConnectRefrigerator Tubing (WX08X10006, WX08X10015 and WX08X10025).

When connecting your refrigerator to a GE Reverse Osmosis Water System, the only approved installation is with a GE RVKit . For other reverse osmosis water systems, follow the manufacturer’s recommendations.

If the water supply to the refrigerator is from a Reverse Osmosis Water Filtration System AND the refrigerator also has a water filter, use the refrigerator’s filter bypass plug. Using the refrigerator’s water filtration cartridge in conjunction with the RO filter can result in hollow ice cubes.

This water line installation is not warranted by the refrigerator or icemaker manufacturer. Follow these instructions carefully to minimize the risk of expensive water damage.

Water hammer (water banging in the pipes) in house plumbing can cause damage to refrigerator parts and lead to water leakage or flooding. Call a qualified plumber to correct water hammer before installing the water supply line to the refrigerator. To prevent burns and product damage, do not hook up the water line to the hot water line.

If you use your refrigerator before connecting the water line, make sure the icemaker power switch is in the O (off) position.

Do not install the icemaker tubing in areas where temperatures fall below freezing.

When using any electrical device (such as a power drill) during installation, be sure the device is double insulated or grounded in a manner to prevent the hazard of electric shock, or is battery powered.

All installations must be in accordance with local plumbing code requirements.

WHAT YOU WILL NEED

Copper or GE SmartConnectRefrigerator Tubing kit, 1/4outer diameter to connect the refrigerator to the water supply. If using copper, be sure both ends of the tubing are cut square.

To determine how much tubing you need: measure the distance from the water valve on the back

of the refrigerator to the water supply pipe. Be sure there is sufficient extra tubing to allow the refrigerator to move out from the wall after installation.

GE SmartConnectRefrigerator Tubing Kits are available in the following lengths:

6(1.8 m) – WX08X10006

15(4.6 m) – WX08X10015

25(7.6 m) – WX08X10025

28

Image 28
Contents Ge.com Write the model and serial numbers here Model # Serial #Before You Throw Away Your Old Refrigerator or FreezerHOW to Connect Electricity Ge.comAbout the controls with temperature settings When to Replace the Filter Installing the Filter CartridgeAbout the water filter. on some models Water Filter CartridgeNon-Adjustable Shelves on the Door on some models About the shelves and binsRearranging the Shelves To removeAbout the crispers and pans Adjustable Humidity Crisper on some modelsFruit and Vegetable Crisper When replacing the deep full-width basket About the freezer drawer. on some modelsFreezer Shelves and Baskets Basket RemovalNon-Adjustable Shelf on Freezer Door About the freezer compartment. on some modelsFreezer Shelf and Basket Fixed Shelf RemovalIcemaker Accessory Kit To reach the icemaker power switch, pullAbout the automatic icemaker. on some models Automatic IcemakerCleaning the Outside Care and cleaning of the refrigeratorCleaning the Inside Preparing for Vacation Behind the RefrigeratorPreparing to Move Refrigerator Lights Replacing the light bulbsFreezer Light Before YOU Begin PreparationTools YOU MAY Need Moving the Refrigerator IndoorsConnecting the Refrigerator to the House Water Line Refrigerator LocationClearances Removetop CAP cont. on some modelsCont Turn on the Water SupplyPlug in the Refrigerator PUT Therefrigerator in PlaceRemove the Fresh Food Door Handle Remove the FreezerdoorhandleAttach the Fresh Food Door Handle Attach the FreezerdoorhandleSET the Controls Leveling legs have 2 purposesRemovethebasket RemovethedrawerfrontRemovethedrawerfront Remove the Base GrilleReplace the Freezer Basket Attachand Securethedrawer Front TotheslidesReversingthedoorswing Single Door Refrigerator Models only Important NotesTools YOU will Need Removethe Refrigerator DoorTransfer Center Hinge Bracket Remove the Freezer DoorRemove Bottom Hinge and Leveling LEG Rehangfreezerdoor Transfer Refrigerator Doorhandle TorightRehangrefrigeratordoor Install the Logo BadgeDouble Door Refrigerator Models only Removing the Doors Double Door Refrigerator Models only Removetherefrigerator DoorsRemovecenterhinge Removeopposite DoorInstall Centerhinge RehangrefrigeratordoorsReplaceopposite Door Align Double DoorsInstalling the Water Line Icemaker Models What YOU will NeedChoose the Valve Location Shut OFF the Main Water SupplyDrill the Hole for the Valve Fasten the Shutoff Valve Connect the Tubing to the ValveTighten the Pipe Clamp Route the TubingBefore you call for service… Normal operating soundsConsumer Support Troubleshooting Tips See About the controlsSee Replacing the light bulbs Handle is loose Handle needs adjusting Should be positioned verticallyGE Service Protection Plus Warranty Registration Department Box Louisville, KYConsumer Product Ownership Registration Model NumberOwnership Registration Page GE Will Replace What GE Will Not CoverGE and Geprofilemodels One Year Thirty DaysWhat is not Covered Terms and ConditionsPerformance Data Sheet Operating SpecificationsGeneral Installation/Operation/Maintenance Requirements Special NoticesWater Treatment Device

200D9366P004 specifications

The GE 200D9366P004 is a high-performance component designed for various industrial applications, particularly in power generation and distribution systems. This device is a part of General Electric’s extensive lineup of electrical components, renowned for their durability and operational efficiency.

One of the main features of the GE 200D9366P004 is its robust design capacity, built to handle significant electrical loads while maintaining stability and safety. The component is engineered to comply with rigorous industry standards, ensuring not only reliability but also longevity in harsh operational environments. This makes it suitable for a range of applications, from power plants to critical infrastructure systems.

In terms of technologies, the GE 200D9366P004 incorporates advanced electric and electronic control systems that enhance its operational capabilities. This includes state-of-the-art monitoring technologies that provide real-time data on performance metrics, allowing for prompt detection of anomalies and facilitating proactive maintenance strategies. This predictive capability is crucial in minimizing downtime and extending the lifecycle of the equipment.

The operating characteristics of the GE 200D9366P004 are particularly noteworthy. It is designed for optimal thermal performance, ensuring that heat dissipation is managed efficiently. This helps in maintaining consistent performance even under high operational loads. Additionally, the component features advanced insulating materials that contribute to its reliability and efficiency, reducing the risks associated with electrical failures.

Another notable characteristic is its modular design, which simplifies installation and maintenance processes. This modularity allows for easier upgrades and repairs, making it a flexible choice for many organizations looking to enhance their operational efficiency without extensive downtime.

Overall, the GE 200D9366P004 stands out in the industrial landscape for its combination of advanced technology, rugged reliability, and operational efficiency. Whether utilized in power generation, industrial automation, or management of critical electrical infrastructure, this component exemplifies GE’s commitment to quality and innovation in electrical solutions, making it a preferred choice for professionals aiming to achieve high-performance standards in their operations.