GE 200D9366P004 operating instructions SET the Controls, Leveling legs have 2 purposes

Page 19

Installation Instructions

10LEVEL THE REFRIGERATOR

The leveling legs have 2 purposes:

1)Leveling legs adjust so the refrigerator is firmly positioned on the floor and does not wobble.

2)Leveling legs serve as a stabilizing brake to hold the refrigerator securely in position during operation and cleaning. The leveling legs also prevent the refrigerator from tipping.

ARemove the grille by removing the two Phillips head screws.

BTurn the leveling legs clockwise to raise

the refrigerator, counterclockwise to lower it .

CAUTION: To avoid possible personal injury or property damage, the leveling legs must be firmly touching the floor.

CReplace the base grille by inserting the two Phillips head screws.

19

11SET THE CONTROLS

Set the controls to the recommended setting.

12REMOVE PACKAGING, START ICEMAKER (icemaker models)

A)Remove all tape, foam and protective packing from shelves and drawers.

B)Remove the tie downs from the freezer baskets.

C)Place half width basket onto drawer slides. See About the freezer section for instructions.

Set the icemaker power switch to the I(on) position. The icemaker will not begin to operate until it reaches its operating temperature of 15°F (–9°C) or below. It will then begin operation automatically. It will take 2–3 days to fill the ice bin.

Power switch

NOTE: In lower water pressure conditions, the water valve may turn on up to 3 times to deliver enough water to the icemaker.

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Write the model and serial numbers here Model # Serial # Ge.comRefrigerator or Freezer Before You Throw Away Your OldGe.com HOW to Connect ElectricityAbout the controls with temperature settings Water Filter Cartridge When to Replace the FilterInstalling the Filter Cartridge About the water filter. on some modelsTo remove Non-Adjustable Shelves on the Door on some modelsAbout the shelves and bins Rearranging the ShelvesAbout the crispers and pans Adjustable Humidity Crisper on some modelsFruit and Vegetable Crisper Basket Removal When replacing the deep full-width basketAbout the freezer drawer. on some models Freezer Shelves and BasketsFixed Shelf Removal Non-Adjustable Shelf on Freezer DoorAbout the freezer compartment. on some models Freezer Shelf and BasketAutomatic Icemaker Icemaker Accessory KitTo reach the icemaker power switch, pull About the automatic icemaker. on some modelsCleaning the Outside Care and cleaning of the refrigeratorCleaning the Inside Preparing for Vacation Behind the RefrigeratorPreparing to Move Refrigerator Lights Replacing the light bulbsFreezer Light Moving the Refrigerator Indoors Before YOU BeginPreparation Tools YOU MAY NeedRemovetop CAP cont. on some models Connecting the Refrigerator to the House Water LineRefrigerator Location ClearancesPUT Therefrigerator in Place ContTurn on the Water Supply Plug in the RefrigeratorRemove the Freezerdoorhandle Remove the Fresh Food Door HandleAttach the Freezerdoorhandle Attach the Fresh Food Door HandleLeveling legs have 2 purposes SET the ControlsRemove the Base Grille RemovethebasketRemovethedrawerfront RemovethedrawerfrontAttachand Securethedrawer Front Totheslides Replace the Freezer BasketRemovethe Refrigerator Door Reversingthedoorswing Single Door Refrigerator Models onlyImportant Notes Tools YOU will NeedTransfer Center Hinge Bracket Remove the Freezer DoorRemove Bottom Hinge and Leveling LEG Transfer Refrigerator Doorhandle Toright RehangfreezerdoorRehangrefrigeratordoor Install the Logo BadgeDouble Door Refrigerator Models only Removeopposite Door Removing the Doors Double Door Refrigerator Models onlyRemovetherefrigerator Doors RemovecenterhingeAlign Double Doors Install CenterhingeRehangrefrigeratordoors Replaceopposite DoorWhat YOU will Need Installing the Water Line Icemaker ModelsChoose the Valve Location Shut OFF the Main Water SupplyDrill the Hole for the Valve Route the Tubing Fasten the Shutoff ValveConnect the Tubing to the Valve Tighten the Pipe ClampNormal operating sounds Before you call for service…See About the controls Consumer Support Troubleshooting TipsSee Replacing the light bulbs Should be positioned vertically Handle is loose Handle needs adjustingWarranty Registration Department Box Louisville, KY GE Service Protection PlusModel Number Consumer Product Ownership RegistrationOwnership Registration Page Thirty Days GE Will ReplaceWhat GE Will Not Cover GE and Geprofilemodels One YearTerms and Conditions What is not CoveredSpecial Notices Performance Data SheetOperating Specifications General Installation/Operation/Maintenance RequirementsWater Treatment Device

200D9366P004 specifications

The GE 200D9366P004 is a high-performance component designed for various industrial applications, particularly in power generation and distribution systems. This device is a part of General Electric’s extensive lineup of electrical components, renowned for their durability and operational efficiency.

One of the main features of the GE 200D9366P004 is its robust design capacity, built to handle significant electrical loads while maintaining stability and safety. The component is engineered to comply with rigorous industry standards, ensuring not only reliability but also longevity in harsh operational environments. This makes it suitable for a range of applications, from power plants to critical infrastructure systems.

In terms of technologies, the GE 200D9366P004 incorporates advanced electric and electronic control systems that enhance its operational capabilities. This includes state-of-the-art monitoring technologies that provide real-time data on performance metrics, allowing for prompt detection of anomalies and facilitating proactive maintenance strategies. This predictive capability is crucial in minimizing downtime and extending the lifecycle of the equipment.

The operating characteristics of the GE 200D9366P004 are particularly noteworthy. It is designed for optimal thermal performance, ensuring that heat dissipation is managed efficiently. This helps in maintaining consistent performance even under high operational loads. Additionally, the component features advanced insulating materials that contribute to its reliability and efficiency, reducing the risks associated with electrical failures.

Another notable characteristic is its modular design, which simplifies installation and maintenance processes. This modularity allows for easier upgrades and repairs, making it a flexible choice for many organizations looking to enhance their operational efficiency without extensive downtime.

Overall, the GE 200D9366P004 stands out in the industrial landscape for its combination of advanced technology, rugged reliability, and operational efficiency. Whether utilized in power generation, industrial automation, or management of critical electrical infrastructure, this component exemplifies GE’s commitment to quality and innovation in electrical solutions, making it a preferred choice for professionals aiming to achieve high-performance standards in their operations.
Top Page Image Contents