Denon AVR-3801 manual Connecting the antenna terminals

Page 10

Connecting the antenna terminals

DIRECTION OF

BROADCASTING

STATION

AM LOOP ANTENNA (Supplied)

75Ω /ohms

COAXIAL CABLE

FM ANTENNA ADAPTER (Supplied)

FM ANTENNA

300 Ω /ohms

FEEDER

CABLE

AM OUTDOOR

ANTENNA

FM INDOOR ANTENNA (Supplied)

300 Ω /ohms

GROUND

•An F-type FM antenna cable plug can be connected directly.

•If the FM antenna cable’s plug is not of the F-type, connect using the included antenna adapter.

AM loop antenna assembly

FM antenna adopter assembly

Remove the vinyl tie and take out the connection line.

a. With the antenna on top any stable surface.

Mount

b. With the antenna attached to a wall.

Connect to the AM antenna terminals.

Bend in the reverse direction.

75 Ω /ohms COAXIAL CABLE

Open the cover

SHUT

PULL

CLAMP

CLAMP

PULL

ANTENNA ADAPTER

SHUT

REMOVE

CLAMP

CLAMP

Installation hole Mount on wall, etc.

Connection of AM antennas

1. Push the lever. 2. Insert the conductor. 3. Return the lever.

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

Notes:

•Do not connect two FM antennas simultaneously.

•Even if an external AM antenna is used, do not disconnect the AM loop antenna.

•Make sure AM loop antenna lead terminals do not touch metal parts of the panel.

9

Image 10

Contents AVR-3801 Page Safety Precautions Safety Instructions Table of Contents Before UsingFeatures Connecting the audio components ConnectionsConnecting video components Connecting a monitor TV Connecting a video component equipped with S-Video jacksPrecaution when using S-jacks Connecting the video decksConnecting the antenna terminals AM loop antenna assembly FM antenna adopter assemblyConnecting a DVD player DVD in jacks Connecting a monitor TV Monitor OUT jackConnecting the external input EXT. in jacks Connecting the Multi Zone jacksSpeaker system connections Connecting banana plugsPrecautions when connecting speakers ConnectionsProtector circuit Front Panel Surround speaker system indicatorsPart Names and Functions Surround Speaker A/BRemote control unit DISPLAY/SURR. ParaPress this to display the system setup menu Setting UP the SystemSystem Setup button Cursor buttonsSurround speaker selector function Setting the power amplifier assignment Before setting up the systemSetting the type of speakers Parameters Assignment of low frequency signal range Setting the Subwoofer modeSubwoofer mode OFF Setting the delay timeSetting PreparationsSelect the speaker to be set Delay Time screen appears automaticallyOnce Meters or Feet is selected in , Set the distance betweenSetting the channel level Switch to the Channel Level screen Select Test Tone ModeSelect Yes Select Test Tone StartIs the same To select the input source Setting the Digital In AssignmentTo select the digital input jack Switch to the On Screen Display screen Select on or OFF Setting the on-screen display OSDSet the multi pre-out output level adjustment Multi Vol. LevelAuto tuner presets Press the Enter button Auto Preset Memory screen appearsAfter completing system setup On-screen display signalsUsing the remote control unit Remote Control UnitInserting the batteries MD recorder MD, CD recorder CDR system buttons Operating Denon audio componentsCD player CD system buttons Tape deck Tape system buttonsCode no ResetEnter Code LearnChecking the preset memory settings Operating a component stored in the preset memoryOperate the component Learning function System call Storing system call signalsSYS Mode System call buttonsUsing the system call function ResettingResetting the system call buttons SYS Mode SYS Call Reset PRE Reset LRNReset ALL Reset SYS Resetting the preset memoryResetting learned buttons All reset function Auto search function Before operating Turn on the power Press the Power switch buttonOperation Refer to Connections pages 6 to 13 and check that allPlaying the input source To select the input source when RECInput mode selection function Select the input source to be playedInput signal display Input mode displayExample Stereo After starting playback Adjusting the sound quality ToneListening over headphones Turning the sound off temporarily MutingMulti-source recording/playback Playing one source while recording another REC OUT modeChecking the currently playing program source, etc Select Multi using Display switches as follows eachThis operation is not possible in the REC OUT mode Multi source switchesSet the external input EXT Playback using the external input EXT. in jacksPress the EXT. in to switch External input ModeMulti-source and multi-zone playback Multi Room Music Entertainment SystemSurround Before playing with the surround functionDolby Surround Pro Logic mode Fader functionSignal Detect indicator lights Set the input mode to Auto or DTSSelect the Dolby/DTS Surround mode When playing sources On whichCOMP. Dynamic Range Compression 7.1 SurroundSurround parameters q Cinema EQ. Cinema Equalizer LFE Low Frequency EffectDSP Surround Simulation Surround modes and their featuresPersonal Memory Plus DSP surround simulation Set the parametersWhen turned counterclockwise When turned clockwisePress the Surround Parameter button Tone control setting Cinema MusicListening to the Radio Auto tuningManual tuning TunerPreset memory Checking the preset stationsLast Function Memory Recalling preset stationsInitialization of the Microprocessor Troubleshooting Additional Information Types of multi-channel signalsMovie audio Surround back speakers Number of surround back speakersSpeaker setting examples When using different surround speakers for movies and music When not using surround back speakers2Dolby Digital and Dolby Pro Logic SurroundDolby Surround Dolby Digital Dolby Surround AC-3 Dolby Digital compatible media and playback methodsDolby Pro Logic compatible media and playback methods DTS Digital SurroundDolby Pro Logic DTS compatible media and playback methodsDTS Neo6TM surround DTS-ESTMDiscreteDTS-ESTMMatrix DTS Neo6 CinemaSurround modes and parameters DVD VDP Tape TV/DBS VCR-1 VCR-2Specifications 14-14, Akasaka 4-CHOME, MINATO-KU, Tokyo 107-8011, Japan