Denon AVR-3801 manual Once Meters or Feet is selected in, Delay Time screen appears automatically

Page 23

2

Switch to the Delay Time screen.

ENTER

 

SHIFT

3

TUNING

BAND

MODE

 

TUNING

Select the desired unit, meters or feet.

Select (darken) the desired units, “Meters” or “Feet”.

Example: When “Feet” is selected

4

Once “Meters” or “Feet” is selected in step 3, the

 

 

Delay Time screen appears automatically.

5

6

Select the speaker to be set.

 

TUNING

BAND

MODE

 

TUNING

Set the distance between the

 

TUNING

 

center speaker and listening

 

 

 

 

 

 

position.

BAND

 

MODE

The distance changes in units of 1

 

 

 

 

TUNING

 

foot (0.1 meters) each time the

 

 

 

button is pressed. Select the value

 

 

 

closest to the measured distance.

Example: When the distance is set to 12 feet for the center speaker

If “Yes” is selected for “Default”, the settings are automatically reset to the default values.

Please note that the difference of distance for every speaker should be 15 ft (4.5 m) or less. If you set an invalid distance, a CAUTION notice, such as screen right will appear. In this case, please relocate the blinking speaker(s) so that its distance is no larger than the value shown in highlighted line.

22

Image 23
Contents AVR-3801 Page Safety Precautions Safety Instructions Before Using Table of ContentsFeatures Connections Connecting the audio componentsConnecting video components Connecting the video decks Connecting a video component equipped with S-Video jacksPrecaution when using S-jacks Connecting a monitor TVAM loop antenna assembly FM antenna adopter assembly Connecting the antenna terminalsConnecting a monitor TV Monitor OUT jack Connecting a DVD player DVD in jacksConnecting the Multi Zone jacks Connecting the external input EXT. in jacksConnections Connecting banana plugsPrecautions when connecting speakers Speaker system connectionsProtector circuit Surround Speaker A/B Surround speaker system indicatorsPart Names and Functions Front PanelDISPLAY/SURR. Para Remote control unitCursor buttons Setting UP the SystemSystem Setup button Press this to display the system setup menuSurround speaker selector function Setting the type of speakers Before setting up the systemSetting the power amplifier assignment Parameters Subwoofer mode Setting the Subwoofer modeAssignment of low frequency signal range Preparations Setting the delay timeSetting OFFSet the distance between Delay Time screen appears automaticallyOnce Meters or Feet is selected in , Select the speaker to be setSwitch to the Channel Level screen Select Test Tone Mode Setting the channel levelIs the same Select Test Tone StartSelect Yes To select the digital input jack Setting the Digital In AssignmentTo select the input source Multi Vol. Level Setting the on-screen display OSDSet the multi pre-out output level adjustment Switch to the On Screen Display screen Select on or OFFPress the Enter button Auto Preset Memory screen appears Auto tuner presetsOn-screen display signals After completing system setupInserting the batteries Remote Control UnitUsing the remote control unit Tape deck Tape system buttons Operating Denon audio componentsCD player CD system buttons MD recorder MD, CD recorder CDR system buttonsLearn ResetEnter Code Code noOperating a component stored in the preset memory Checking the preset memory settingsOperate the component Learning function System call buttons Storing system call signalsSYS Mode System callResetting the system call buttons ResettingUsing the system call function Resetting the preset memory Reset PRE Reset LRNReset ALL Reset SYS SYS Mode SYS CallResetting learned buttons All reset function Auto search function Refer to Connections pages 6 to 13 and check that all Turn on the power Press the Power switch buttonOperation Before operatingSelect the input source to be played To select the input source when RECInput mode selection function Playing the input sourceExample Stereo Input mode displayInput signal display Turning the sound off temporarily Muting Adjusting the sound quality ToneListening over headphones After starting playbackChecking the currently playing program source, etc Playing one source while recording another REC OUT modeMulti-source recording/playback Multi source switches Display switches as follows eachThis operation is not possible in the REC OUT mode Select Multi usingMode Playback using the external input EXT. in jacksPress the EXT. in to switch External input Set the external input EXTMulti Room Music Entertainment System Multi-source and multi-zone playbackBefore playing with the surround function SurroundFader function Dolby Surround Pro Logic modeWhen playing sources On which Set the input mode to Auto or DTSSelect the Dolby/DTS Surround mode Signal Detect indicator lightsLFE Low Frequency Effect 7.1 SurroundSurround parameters q Cinema EQ. Cinema Equalizer COMP. Dynamic Range CompressionPersonal Memory Plus Surround modes and their featuresDSP Surround Simulation Set the parameters DSP surround simulationPress the Surround Parameter button When turned clockwiseWhen turned counterclockwise Tone control setting Music CinemaTuner Auto tuningManual tuning Listening to the RadioChecking the preset stations Preset memoryInitialization of the Microprocessor Recalling preset stationsLast Function Memory Troubleshooting Movie audio Types of multi-channel signalsAdditional Information Number of surround back speakers Surround back speakersSpeaker setting examples When not using surround back speakers When using different surround speakers for movies and musicDolby Digital compatible media and playback methods SurroundDolby Surround Dolby Digital Dolby Surround AC-3 2Dolby Digital and Dolby Pro LogicDTS compatible media and playback methods DTS Digital SurroundDolby Pro Logic Dolby Pro Logic compatible media and playback methodsDTS Neo6 Cinema DTS-ESTMDiscreteDTS-ESTMMatrix DTS Neo6TM surroundDVD VDP Tape TV/DBS VCR-1 VCR-2 Surround modes and parametersSpecifications 14-14, Akasaka 4-CHOME, MINATO-KU, Tokyo 107-8011, Japan