Denon AVR-3801 manual Setting the Digital In Assignment, To select the input source

Page 26

When you adjust the channel levels while in the SYSTEM SETUP CHANNEL LEVEL mode, the channel level adjustments made will affect ALL surround modes. Consider this mode a Master Channel Level adjustment mode.

After you have completed the SYSTEM SETUP CHANNEL LEVEL adjustments, you can then activate the individual surround modes and adjust channel levels that will be remembered for each of those modes. Then, whenever you activate a particular surround sound mode, your preferred channel level adjustments for just that mode will be recalled. Check the instructions for adjusting channel levels within each surround mode on page 49.

You can adjust the channel levels for each of the following surround modes: DIRECT, STEREO, 5/7 CH STEREO, DOLBY/DTS SURROUND, WIDE SCREEN, ROCK ARENA, JAZZ CLUB, VIDEO GAME, MONO MOVIE, and MATRIX.

When using either surround speakers A or B, or when using surround speakers A and B at the same time, be sure to adjust the balance of playback levels between each channel for the various selections of “A or B” and “A and B”.

Setting the Digital In Assignment

• This setting assigns the digital input jacks of the AVR-3801 for the different input sources.

1

At the System Setup Menu select “Digital In Assignment”.

 

 

TUNING

BAND

MODE

 

TUNING

2

ENTER

SHIFT

Switch to the Digital Inputs screen.

3

4

Select the digital input jack to be assigned to the input source.

TUNING

 

 

TUNING

•

To select the input source

 

 

 

 

BAND

MODE

 

 

•

To select the digital input jack

BAND

MODE

Select “OFF” for input sources for which no digital input jacks are used.

 

 

 

 

 

 

TUNING

 

 

TUNING

 

If “Yes” is selected for “Default”, the settings are automatically reset to the default values.

ENTER

 

Enter the setting.

 

 

 

 

The System Setup Menu reappears.

SHIFT

NOTES:

•The OPTICAL 3 jacks on the AVR-3801’s rear panel are equipped with an optical digital output jack for recording digital signals on a CD recorder, MD recorder or other digital recorder. Use this for digital recording between a digital audio source (stereo - 2 channel) and a digital audio recorder.

•Do not connect the output of the component connected to the OPTICAL 3 OUT jack on the AVR-3801’s rear panel to any jack other than the OPTICAL 3 IN jack.

•“PHONO” and “TUNER” cannot be selected on the Digital In Assignment screen.

25

Page 25 Page 27
Image 26
Page 25 Page 27
Contents AVR-3801 Page Safety Precautions Safety Instructions Table of Contents Before UsingFeatures Connecting the audio components ConnectionsConnecting video components Connecting a monitor TV Connecting a video component equipped with S-Video jacksPrecaution when using S-jacks Connecting the video decksConnecting the antenna terminals AM loop antenna assembly FM antenna adopter assemblyConnecting a DVD player DVD in jacks Connecting a monitor TV Monitor OUT jackConnecting the external input EXT. in jacks Connecting the Multi Zone jacksSpeaker system connections Connecting banana plugsPrecautions when connecting speakers ConnectionsProtector circuit Front Panel Surround speaker system indicatorsPart Names and Functions Surround Speaker A/BRemote control unit DISPLAY/SURR. ParaPress this to display the system setup menu Setting UP the SystemSystem Setup button Cursor buttonsSurround speaker selector function Setting the type of speakers Before setting up the systemSetting the power amplifier assignment Parameters Subwoofer mode Setting the Subwoofer modeAssignment of low frequency signal range OFF Setting the delay timeSetting PreparationsSelect the speaker to be set Delay Time screen appears automaticallyOnce Meters or Feet is selected in , Set the distance betweenSetting the channel level Switch to the Channel Level screen Select Test Tone ModeIs the same Select Test Tone StartSelect Yes To select the digital input jack Setting the Digital In AssignmentTo select the input source Switch to the On Screen Display screen Select on or OFF Setting the on-screen display OSDSet the multi pre-out output level adjustment Multi Vol. LevelAuto tuner presets Press the Enter button Auto Preset Memory screen appearsAfter completing system setup On-screen display signalsInserting the batteries Remote Control UnitUsing the remote control unit MD recorder MD, CD recorder CDR system buttons Operating Denon audio componentsCD player CD system buttons Tape deck Tape system buttonsCode no ResetEnter Code LearnChecking the preset memory settings Operating a component stored in the preset memoryOperate the component Learning function System call Storing system call signalsSYS Mode System call buttonsResetting the system call buttons ResettingUsing the system call function SYS Mode SYS Call Reset PRE Reset LRNReset ALL Reset SYS Resetting the preset memoryResetting learned buttons All reset function Auto search function Before operating Turn on the power Press the Power switch buttonOperation Refer to Connections pages 6 to 13 and check that allPlaying the input source To select the input source when RECInput mode selection function Select the input source to be playedExample Stereo Input mode displayInput signal display After starting playback Adjusting the sound quality ToneListening over headphones Turning the sound off temporarily MutingChecking the currently playing program source, etc Playing one source while recording another REC OUT modeMulti-source recording/playback Select Multi using Display switches as follows eachThis operation is not possible in the REC OUT mode Multi source switchesSet the external input EXT Playback using the external input EXT. in jacksPress the EXT. in to switch External input ModeMulti-source and multi-zone playback Multi Room Music Entertainment SystemSurround Before playing with the surround functionDolby Surround Pro Logic mode Fader functionSignal Detect indicator lights Set the input mode to Auto or DTSSelect the Dolby/DTS Surround mode When playing sources On whichCOMP. Dynamic Range Compression 7.1 SurroundSurround parameters q Cinema EQ. Cinema Equalizer LFE Low Frequency EffectPersonal Memory Plus Surround modes and their featuresDSP Surround Simulation DSP surround simulation Set the parametersPress the Surround Parameter button When turned clockwiseWhen turned counterclockwise Tone control setting Cinema MusicListening to the Radio Auto tuningManual tuning TunerPreset memory Checking the preset stationsInitialization of the Microprocessor Recalling preset stationsLast Function Memory Troubleshooting Movie audio Types of multi-channel signalsAdditional Information Surround back speakers Number of surround back speakersSpeaker setting examples When using different surround speakers for movies and music When not using surround back speakers2Dolby Digital and Dolby Pro Logic SurroundDolby Surround Dolby Digital Dolby Surround AC-3 Dolby Digital compatible media and playback methodsDolby Pro Logic compatible media and playback methods DTS Digital SurroundDolby Pro Logic DTS compatible media and playback methodsDTS Neo6TM surround DTS-ESTMDiscreteDTS-ESTMMatrix DTS Neo6 CinemaSurround modes and parameters DVD VDP Tape TV/DBS VCR-1 VCR-2Specifications 14-14, Akasaka 4-CHOME, MINATO-KU, Tokyo 107-8011, Japan
Top Page Image Contents