Denon AVR-3801 manual After starting playback, Adjusting the sound quality Tone

Page 45

After starting playback

[1] Adjusting the sound quality (TONE)

The tone control function will not work in the direct mode.

1

The tone switches as follows each time the TONE CONTROL

 

 

button is pressed.

 

 

TONE

 

 

CONTROL

 

 

BASS

TREBLE

2

(Main unit)

 

With the name of the volume to be

SELECT

adjusted selected, turn the SELECT knob to adjust the level.

(Main unit)

To increase the bass or treble: Turn the control clockwise. (The bass or treble sound can be increased to up to +12 dB in steps of 2 dB.)

To decrease the bass or treble: Turn the control clockwise. (The bass or treble sound can be decreased to up to –12 dB in steps of 2 dB.)

[2]Listening over headphones

1

Connect the headphones to the

PHONES

PHONES jack of the front panel.

 

 

 

 

 

1

2

Press the OUTPUT button to play the sound over the

 

 

headphones only.

 

TV/

0

+10

 

VCR

 

OUTPUT

 

 

2

TEST

SPEAKER

OUTPUT

TONE

 

SURROUND

 

 

DOLBY/DTS

DSP

5CH / 7CH

 

SURROUND

SIMU.

STEREO

 

The output to the speaker and pre-out jacks is turned off and no sound is produced from the speakers.

Caution: Switching off the power of the unit and the unit will cancel the settings.

[3] Turning the sound off temporarily (MUTING)

1

Use this to turn off the audio output

 

 

 

 

temporarily.

MUTING

 

Press the MUTING button.

 

Cancelling MUTING mode.

Press the MUTING button again.

(Remote control unit)

NOTE:

To prevent hearing loss, do not raise the volume level excessively when using headphones.

TUNING

+

 

+

 

SKIP

ENTER

 

-

SHIFT

-

 

SKIP

MUTING

1

TUNER

PHONO

CD

1 2 3

44

Image 45
Contents AVR-3801 Page Safety Precautions Safety Instructions Before Using Table of ContentsFeatures Connections Connecting the audio componentsConnecting video components Precaution when using S-jacks Connecting a video component equipped with S-Video jacksConnecting a monitor TV Connecting the video decksAM loop antenna assembly FM antenna adopter assembly Connecting the antenna terminalsConnecting a monitor TV Monitor OUT jack Connecting a DVD player DVD in jacksConnecting the Multi Zone jacks Connecting the external input EXT. in jacksPrecautions when connecting speakers Connecting banana plugsSpeaker system connections ConnectionsProtector circuit Part Names and Functions Surround speaker system indicatorsFront Panel Surround Speaker A/BDISPLAY/SURR. Para Remote control unitSystem Setup button Setting UP the SystemPress this to display the system setup menu Cursor buttonsSurround speaker selector function Before setting up the system Setting the power amplifier assignmentSetting the type of speakers Parameters Setting the Subwoofer mode Assignment of low frequency signal rangeSubwoofer mode Setting Setting the delay timeOFF PreparationsOnce Meters or Feet is selected in , Delay Time screen appears automaticallySelect the speaker to be set Set the distance betweenSwitch to the Channel Level screen Select Test Tone Mode Setting the channel levelSelect Test Tone Start Select YesIs the same Setting the Digital In Assignment To select the input sourceTo select the digital input jack Set the multi pre-out output level adjustment Setting the on-screen display OSDSwitch to the On Screen Display screen Select on or OFF Multi Vol. LevelPress the Enter button Auto Preset Memory screen appears Auto tuner presetsOn-screen display signals After completing system setupRemote Control Unit Using the remote control unitInserting the batteries CD player CD system buttons Operating Denon audio componentsMD recorder MD, CD recorder CDR system buttons Tape deck Tape system buttonsEnter Code ResetCode no LearnOperating a component stored in the preset memory Checking the preset memory settingsOperate the component Learning function SYS Mode Storing system call signalsSystem call System call buttonsResetting Using the system call functionResetting the system call buttons Reset ALL Reset SYS Reset PRE Reset LRNSYS Mode SYS Call Resetting the preset memoryResetting learned buttons All reset function Auto search function Operation Turn on the power Press the Power switch buttonBefore operating Refer to Connections pages 6 to 13 and check that allInput mode selection function To select the input source when RECPlaying the input source Select the input source to be playedInput mode display Input signal displayExample Stereo Listening over headphones Adjusting the sound quality ToneAfter starting playback Turning the sound off temporarily MutingPlaying one source while recording another REC OUT mode Multi-source recording/playbackChecking the currently playing program source, etc This operation is not possible in the REC OUT mode Display switches as follows eachSelect Multi using Multi source switchesPress the EXT. in to switch External input Playback using the external input EXT. in jacksSet the external input EXT ModeMulti Room Music Entertainment System Multi-source and multi-zone playbackBefore playing with the surround function SurroundFader function Dolby Surround Pro Logic modeSelect the Dolby/DTS Surround mode Set the input mode to Auto or DTSSignal Detect indicator lights When playing sources On whichSurround parameters q Cinema EQ. Cinema Equalizer 7.1 SurroundCOMP. Dynamic Range Compression LFE Low Frequency EffectSurround modes and their features DSP Surround SimulationPersonal Memory Plus Set the parameters DSP surround simulationWhen turned clockwise When turned counterclockwisePress the Surround Parameter button Tone control setting Music CinemaManual tuning Auto tuningListening to the Radio TunerChecking the preset stations Preset memoryRecalling preset stations Last Function MemoryInitialization of the Microprocessor Troubleshooting Types of multi-channel signals Additional InformationMovie audio Number of surround back speakers Surround back speakersSpeaker setting examples When not using surround back speakers When using different surround speakers for movies and musicDolby Surround Dolby Digital Dolby Surround AC-3 Surround2Dolby Digital and Dolby Pro Logic Dolby Digital compatible media and playback methodsDolby Pro Logic DTS Digital SurroundDolby Pro Logic compatible media and playback methods DTS compatible media and playback methodsDTS-ESTMMatrix DTS-ESTMDiscreteDTS Neo6TM surround DTS Neo6 CinemaDVD VDP Tape TV/DBS VCR-1 VCR-2 Surround modes and parametersSpecifications 14-14, Akasaka 4-CHOME, MINATO-KU, Tokyo 107-8011, Japan