Denon AVR-3801 manual Input mode display, Example Stereo, Input signal display

Page 44

• Selecting the PCM mode

Input mode display

Press the PCM button to switch to the PCM signal input.

PCM

(Main unit)

•Selecting the DTS mode

Press the DTS button to switch to the DTS signal input.

DTS

		(Main unit)

3	Select the play mode.
3	Example: Stereo
	SURROUND	SELECT
	MODE

STEREO

(Main unit)

(Remote control unit)

To select the surround mode while adjusting the surround parameters, channel volume or tone control, press the surround mode button then operate the selector.

SURROUND

MODE

• In the AUTO mode

INPUT

AUTO PCMDTS

• In the DIGITAL PCM mode

INPUT

AUTO PCMDTS

• In the DIGITAL DTS mode

INPUT

AUTO PCMDTS

• In the ANALOG mode

INPUT

AUTO PCMDTS

Input signal display

• DOLBY DIGITAL

SIGNAL

LOCK DIGITAL

• DTS

SIGNAL

LOCK DIGITAL

• PCM

SIGNAL

LOCK DIGITAL

One of these lights, depending on the input signal.

DIGITAL ANALOG

DIGITAL

DIGITAL

ANALOG

(Main unit)

4	Start playback on the selected component.
	Start playback on the selected component.
	• For operating instructions, refer to the component’s
	manual.
5	Adjust the volume.
			VOLUME
		MASTER VOLUME	+
			+
			-
	The volume level is
	displayed on the	(Main unit)	(Remote control unit)
	master volume level
	display.

The volume can be adjusted within the range of –60 to 0 to 18 dB, in steps of 1 dB. However, when the channel level is set as described on page 23 or pages 49 and 50, if the volume for any channel is set at +1 dB or greater, the volume cannot be adjusted up to 18 dB. (In this case the maximum volume adjustment range is “18 dB — (Maximum value of channel level)”.)

Input mode when playing DTS sources

•Noise will be output if DTS-compatible CDs or LDs are played in the “ANALOG” or “PCM” mode.

When playing DTS-compatible sources, be sure to connect the source component to the digital input jacks (OPTICAL/COAXIAL) and set the input mode to “DTS”.

The LOCK LED lights when digital signals are being input properly. If the LED does not light, check whether the digital input component setup (page 25) and connections are correct and whether the component’s power is turned on.

NOTE:

•The digital input indicator will light when playing CD-ROMs containing data other than audio signals, but no sound will be heard.

43

Image 44

Contents AVR-3801 Page Safety Precautions Safety Instructions Table of Contents Before UsingFeatures Connecting the audio components ConnectionsConnecting video components Connecting a video component equipped with S-Video jacks Precaution when using S-jacksConnecting a monitor TV Connecting the video decksConnecting the antenna terminals AM loop antenna assembly FM antenna adopter assemblyConnecting a DVD player DVD in jacks Connecting a monitor TV Monitor OUT jackConnecting the external input EXT. in jacks Connecting the Multi Zone jacksConnecting banana plugs Precautions when connecting speakersSpeaker system connections ConnectionsProtector circuit Surround speaker system indicators Part Names and FunctionsFront Panel Surround Speaker A/BRemote control unit DISPLAY/SURR. ParaSetting UP the System System Setup buttonPress this to display the system setup menu Cursor buttonsSurround speaker selector function Setting the type of speakers Before setting up the systemSetting the power amplifier assignment Parameters Subwoofer mode Setting the Subwoofer modeAssignment of low frequency signal range Setting the delay time SettingOFF PreparationsDelay Time screen appears automatically Once Meters or Feet is selected in ,Select the speaker to be set Set the distance betweenSetting the channel level Switch to the Channel Level screen Select Test Tone ModeIs the same Select Test Tone StartSelect Yes To select the digital input jack Setting the Digital In AssignmentTo select the input source Setting the on-screen display OSD Set the multi pre-out output level adjustmentSwitch to the On Screen Display screen Select on or OFF Multi Vol. LevelAuto tuner presets Press the Enter button Auto Preset Memory screen appearsAfter completing system setup On-screen display signalsInserting the batteries Remote Control UnitUsing the remote control unit Operating Denon audio components CD player CD system buttonsMD recorder MD, CD recorder CDR system buttons Tape deck Tape system buttonsReset Enter CodeCode no LearnChecking the preset memory settings Operating a component stored in the preset memoryOperate the component Learning function Storing system call signals SYS ModeSystem call System call buttonsResetting the system call buttons ResettingUsing the system call function Reset PRE Reset LRN Reset ALL Reset SYSSYS Mode SYS Call Resetting the preset memoryResetting learned buttons All reset function Auto search function Turn on the power Press the Power switch button OperationBefore operating Refer to Connections pages 6 to 13 and check that allTo select the input source when REC Input mode selection functionPlaying the input source Select the input source to be playedExample Stereo Input mode displayInput signal display Adjusting the sound quality Tone Listening over headphonesAfter starting playback Turning the sound off temporarily MutingChecking the currently playing program source, etc Playing one source while recording another REC OUT modeMulti-source recording/playback Display switches as follows each This operation is not possible in the REC OUT modeSelect Multi using Multi source switchesPlayback using the external input EXT. in jacks Press the EXT. in to switch External inputSet the external input EXT ModeMulti-source and multi-zone playback Multi Room Music Entertainment SystemSurround Before playing with the surround functionDolby Surround Pro Logic mode Fader functionSet the input mode to Auto or DTS Select the Dolby/DTS Surround modeSignal Detect indicator lights When playing sources On which7.1 Surround Surround parameters q Cinema EQ. Cinema EqualizerCOMP. Dynamic Range Compression LFE Low Frequency EffectPersonal Memory Plus Surround modes and their featuresDSP Surround Simulation DSP surround simulation Set the parametersPress the Surround Parameter button When turned clockwiseWhen turned counterclockwise Tone control setting Cinema MusicAuto tuning Manual tuningListening to the Radio TunerPreset memory Checking the preset stationsInitialization of the Microprocessor Recalling preset stationsLast Function Memory Troubleshooting Movie audio Types of multi-channel signalsAdditional Information Surround back speakers Number of surround back speakersSpeaker setting examples When using different surround speakers for movies and music When not using surround back speakersSurround Dolby Surround Dolby Digital Dolby Surround AC-32Dolby Digital and Dolby Pro Logic Dolby Digital compatible media and playback methodsDTS Digital Surround Dolby Pro LogicDolby Pro Logic compatible media and playback methods DTS compatible media and playback methodsDTS-ESTMDiscrete DTS-ESTMMatrixDTS Neo6TM surround DTS Neo6 CinemaSurround modes and parameters DVD VDP Tape TV/DBS VCR-1 VCR-2Specifications 14-14, Akasaka 4-CHOME, MINATO-KU, Tokyo 107-8011, Japan