Denon AVR-3801 manual Before setting up the system, Setting the power amplifier assignment

Page 19

Before setting up the system

1

Check that all the connections are correct, then turn on the main unit’s power.

2 SETUP

Display the System Setup Menu.

Setting the power amplifier assignment

Make this setting to switch the power amplifier for the surround back channel to Multi.

1

TUNING

ENTER

 

 

At the System Setup Menu, select “Power Amp Assignment” and press the ENTER button

BAND

MODE

SHIFT

TUNING

2

Select “Surround Back” to use as the surround back

channel, “Multi” to use as multi zone out.

TUNING

BANDMODE

TUNING

When “Surround Back” is selected

When “Multi” is selected

3

ENTER

SHIFT

Enter the setting.

The System Setup Menu reappears.

Setting the type of speakers

The composition of the signals output from the different channels and the frequency response are adjusted automatically according to the combination of speakers actually being used.

1

At the System Setup Menu select “Speaker Configuration”.

 

 

TUNING

BAND

MODE

 

TUNING

18

Image 19
Contents AVR-3801 Page Safety Precautions Safety Instructions Before Using Table of ContentsFeatures Connections Connecting the audio componentsConnecting video components Connecting the video decks Connecting a video component equipped with S-Video jacksPrecaution when using S-jacks Connecting a monitor TVAM loop antenna assembly FM antenna adopter assembly Connecting the antenna terminalsConnecting a monitor TV Monitor OUT jack Connecting a DVD player DVD in jacksConnecting the Multi Zone jacks Connecting the external input EXT. in jacksConnections Connecting banana plugsPrecautions when connecting speakers Speaker system connectionsProtector circuit Surround Speaker A/B Surround speaker system indicatorsPart Names and Functions Front PanelDISPLAY/SURR. Para Remote control unitCursor buttons Setting UP the SystemSystem Setup button Press this to display the system setup menuSurround speaker selector function Setting the power amplifier assignment Before setting up the systemSetting the type of speakers Parameters Assignment of low frequency signal range Setting the Subwoofer modeSubwoofer mode Preparations Setting the delay timeSetting OFFSet the distance between Delay Time screen appears automaticallyOnce Meters or Feet is selected in , Select the speaker to be setSwitch to the Channel Level screen Select Test Tone Mode Setting the channel levelSelect Yes Select Test Tone StartIs the same To select the input source Setting the Digital In AssignmentTo select the digital input jack Multi Vol. Level Setting the on-screen display OSDSet the multi pre-out output level adjustment Switch to the On Screen Display screen Select on or OFFPress the Enter button Auto Preset Memory screen appears Auto tuner presetsOn-screen display signals After completing system setupUsing the remote control unit Remote Control UnitInserting the batteries Tape deck Tape system buttons Operating Denon audio componentsCD player CD system buttons MD recorder MD, CD recorder CDR system buttonsLearn ResetEnter Code Code noOperating a component stored in the preset memory Checking the preset memory settingsOperate the component Learning function System call buttons Storing system call signalsSYS Mode System callUsing the system call function ResettingResetting the system call buttons Resetting the preset memory Reset PRE Reset LRNReset ALL Reset SYS SYS Mode SYS CallResetting learned buttons All reset function Auto search function Refer to Connections pages 6 to 13 and check that all Turn on the power Press the Power switch buttonOperation Before operatingSelect the input source to be played To select the input source when RECInput mode selection function Playing the input sourceInput signal display Input mode displayExample Stereo Turning the sound off temporarily Muting Adjusting the sound quality ToneListening over headphones After starting playbackMulti-source recording/playback Playing one source while recording another REC OUT modeChecking the currently playing program source, etc Multi source switches Display switches as follows eachThis operation is not possible in the REC OUT mode Select Multi usingMode Playback using the external input EXT. in jacksPress the EXT. in to switch External input Set the external input EXTMulti Room Music Entertainment System Multi-source and multi-zone playbackBefore playing with the surround function SurroundFader function Dolby Surround Pro Logic modeWhen playing sources On which Set the input mode to Auto or DTSSelect the Dolby/DTS Surround mode Signal Detect indicator lightsLFE Low Frequency Effect 7.1 SurroundSurround parameters q Cinema EQ. Cinema Equalizer COMP. Dynamic Range CompressionDSP Surround Simulation Surround modes and their featuresPersonal Memory Plus Set the parameters DSP surround simulationWhen turned counterclockwise When turned clockwisePress the Surround Parameter button Tone control setting Music CinemaTuner Auto tuningManual tuning Listening to the RadioChecking the preset stations Preset memoryLast Function Memory Recalling preset stationsInitialization of the Microprocessor Troubleshooting Additional Information Types of multi-channel signalsMovie audio Number of surround back speakers Surround back speakersSpeaker setting examples When not using surround back speakers When using different surround speakers for movies and musicDolby Digital compatible media and playback methods SurroundDolby Surround Dolby Digital Dolby Surround AC-3 2Dolby Digital and Dolby Pro LogicDTS compatible media and playback methods DTS Digital SurroundDolby Pro Logic Dolby Pro Logic compatible media and playback methodsDTS Neo6 Cinema DTS-ESTMDiscreteDTS-ESTMMatrix DTS Neo6TM surroundDVD VDP Tape TV/DBS VCR-1 VCR-2 Surround modes and parametersSpecifications 14-14, Akasaka 4-CHOME, MINATO-KU, Tokyo 107-8011, Japan