Rangemaster 90 Gas manual Main Oven check, Fitting the plinth, Customer care, Thank you

Page 30

Fitting the oven burner trim (main gas oven only - supplied with some models only)

The loose oven burner trim hooks onto the front of the oven burner bracket.

Main Oven check

The clock must be set to the time of day before the ovens will work.

Press and hold as above.

At the same time, press - or + until the correct time shows.

Don’t forget it’s a 24 hour clock.

If you make a mistake or press the wrong button, turn off the power supply for a minute or two and start again.

CONTROL KNOB (THERMOSTAT) CHECK

If (AUTO) is flashing, press and release the manual ( ) button. Check each oven in turn. Push in and turn

the control knob to Mark 9. A series of sparks will occur at the oven electrode and when the oven burner lights the sparking will stop. A small flame will appear on the oven burner, but as this flame is ‘sensed’ by the flame supervision device, the gas flow will come on full after a short delay. Heat each oven for 10 minutes at Mark 9 then turn to Mark 1 and check that the flame size has reduced. Turn off each oven and check that the oven burner goes out.

TIMER AND SOLENOID CHECK

Automatic Operation of Timer: The gas supply to each oven can be controlled by the timer. Set a ‘cooking period’ time by pressing and releasing the ( ) button and using the + button to give a time of 2 minutes. By

pressing and releasing the ‘stop time’ button ( ) the stop time is displayed. Add 3 minutes to this time by using the + button. The display will automatically change to show the time of day, the cooking symbol ( ) will go out and (AUTO) will show.

Push in and turn one of the oven knobs to Mark 9, the timer will run until the ‘cook period’ starts, when the oven solenoid will open and the burner will light automatically. The cooking symbol ( ) will show. At the end of the ‘cooking period’ the solenoid will close, the oven burner will go out and the beeper will sound (the beeper may

be stopped by pressing the timer ( ) button). The flashing (AUTO) symbol is a reminder to reset to manual operation. Pressing the reset’ button () once to stop the beep and a second time to return to manual, turn off the oven knob.

CONTROL KNOB (THERMOSTAT) CHECK

Set timer to manual. Check each oven in turn. Push in and turn the control knob to Mark 9. A series of sparks will occur at the oven electrode and when the oven burner lights the sparking will stop. A small flame will appear on the oven burner, but as this flame is ‘sensed’ by the flame supervision device, the gas flow will come on full after a short delay. Heat each oven for 10 minutes at Mark 9 then turn to Mark 1 and check that the flame size has reduced. Turn off each oven and check that the oven burner goes out.

Tall oven

Turn on the Tall oven and check that it heats up.

Fitting the plinth

Loosen the 3 screws along the front bottom edge of the cooker. Hook the central keyhole over the central screw. Twist and fit each end keyhole over their respective screws. Tighten the fixing screws.

Customer care

Please complete your details in the front of the installation section of these instructions. Please inform the user how to operate the cooker and hand over these instructions to the user.

Thank you.

30

Image 30
Contents 90 Gas Users Guide Be safe InstallationThis appliance should not be installed in a boat or caravan Gas and Electricity onContents Hotplate burners Griddle Grill Natural gasLP Gas Main Gas Oven Main Oven shelves HandyrackMain Oven light ‘S’ Slow cookingTall Oven electric Clock Cooking using the timer Auto is showing, you want to reset to manual cookingClock Special Features Oven cooking Steam to disperseMain Gas Oven cooking guide Tall Fan electric Oven cooking guide LH hotplate Cleaning your cookerHotplate burners Wok burnerGrill GriddleControl Panel and Doors OvensOutside of cooker Cleaning Table HotplatePart Finish Recommended Cleaning Method Oven and GrillMoving your cooker Tall OvenRemoving the Main Oven Linings Troubleshooting Oven temperature getting hotter as the cooker gets older Oven not coming on when turned on manuallyOven not coming on when automatic cooking Turn off the power supply0800 111 General Safety InstructionsIf you smell gas Don’t smokeThis appliance is heavy, take care when moving it Location of Cooker InstallationProvision of Ventilation They cannot be converted from one gas to the otherDear Installer You will also need the following toolsElectric drill Positioning the Cooker Checking the partsUnpacking the Cooker Moving the Cooker LevellingFitting a stability bracket Fit the HandlesFitting the splash back optional Gas ConnectionElectrical checks Pressure testingElectrical Connection Grill checkCustomer care Main Oven checkFitting the plinth Thank youTo Remove the Control Panel To Remove Ignition/light SwitchServicing Notes To Remove Side PanelsMain RH oven To Remove ClockTo Remove a Thermostat Tall ovenTo Change Grill Electrode To Change Main Oven Burner AssemblyTo Change Grill Burner To Remove Main Oven BurnerTo Remove Grill Door To Adjust Main Oven Door Catch KeepTo Change Main Oven Electrode To Remove Main Oven DoorTo Change Fan in Tall Oven To Change Tall Oven Door Magnetic LatchTo Change Ignition Generator To Remove Tall Oven ElementCircuit Diagram Technical Data Page