hussman P/N 0420057_B operation manual Replace wireway cover Restore power

Page 16

1-10INSTALLATION

3.Align the assembly on the back of the case as shown below.

8.969 for 36-in. Board

8.656 for 48-in. Board

REF

0.812

3.25 REF

8.969 for 36-in. Board

8.656 for 48-in. Board

REF

0.812

0.125-in. Diameter

Drill 6 additional holes 0.5-in. deep

if not already existing in wrapping board.

4.Using holes in wrapping board bracket as a template, mark hole locations on rear of case.

5.Remove wireway cover; make sure there are no wires behind hole locations.

6.Drill 3/8-inch (0.1875) diameter holes for three 1/4-20 thread cutting screws through stain- less steel and structural members.

7.Securely fasten brackets to case.

8.Adjust wrapping board as needed. The attach points for hinging brackets on wrapping board is determined by which position the assembly is to be mounted. Refer to figures for LH, RH or Center mounting positions.

Bottom View of Wrap Board Panel

Wrap Board Panel

 

 

Screw - #8 x1/2

 

PHIL AB SMS

 

(3 required for

 

each bracket)

 

Screw - 1/4-20 x 0.75-in.

 

Flange Thread Cutting

 

(3 required for each bracket)

Bracket - Adj

Bracket Spacer

(2 required)

Screw - 1/4-20 x 0.5-in.

(2 required)

 

Hex Head Zinc Plate

Mounting Holes

(2 required for each bracket)

 

Wrapping Board Assembly for Mounting to Left Hand Side of Case

 

(Facing Front of Case)

Wrap Board Panel

 

 

Screw - #8 x1/2

 

PHIL AB SMS

 

(3 required for

 

each bracket)

 

Screw - 1/4-20 x 0.75-in.

 

Flange Thread Cutting

 

(3 required for each bracket)

Bracket - Adj

Bracket Spacer

(2 required)

Screw - 1/4-20 x 0.5-in.

(2 required)

 

Hex Head Zinc Plate

Mounting Holes

(2 required for each bracket)

 

Wrapping Board Assembly for Mounting to Right Hand Side of Case

 

(Facing Front of Case)

Wrap Board Panel

 

 

Screw - #8 x1/2

 

PHIL AB SMS

 

(3 required for

 

each bracket)

 

Screw - 1/4-20 x 0.75-in.

 

Flange Thread Cutting

 

(3 required for each bracket)

Bracket - Adj

Bracket Spacer

(2 required)

Screw - 1/4-20 x 0.5-in.

(2 required)

 

Hex Head Zinc Plate

Mounting Holes

(2 required for each bracket)

 

Wrapping Board Assembly for Mounting to Center of 12-Ft Case

or Mounting in Positions Other Than Left, Right or Center of Case

 

(Facing Front of Case)

9.Replace wireway cover.

10.Restore power.

P/N 0420057_B

U.S. & Canada 1-800-922-1919 • Mexico 1-800-522-1900 • WWW.HUSSMANN.COM

Image 16
Contents Service Merchandisers Page Contents Service Warranty Revision HistoryRevision B Ansi Z535.5 DefinitionsSafety Service MerchandisersIf in doubt, do not Enter and inform the client NSF Certification InstallationLocation Merchandisers Shipped With END Installed Shipping DamageExterior Loading Shipping BracesCase Leveling PreparationLeveler Adjustment Raise LowerGlass Positioning Adjustment Bolt Optional Flexible Wiper Gasket0420057B Installing Coil Cover and Drip Tray Joining InstructionsDrip Tray Connector Drip Tube Installing Optional Wrap BoardReplace wireway cover Restore power Installing Optional Scale Stand 12INSTALLATION Refrigeration / Electrical RefrigerantRefrigerant Piping Connection LocationControl Settings InsulationSuction Line Liquid LineRefrigeration Thermostat Defrost Termination ThermostatField Wiring Identification of WiringMerchandiser Electrical Data Electrical ConnectionsDrip Piping and Splashguards Installing Drip PipingWaste Outlet and Water Seal Installing Splashguard and Lower Front Panel To Install Lower Front PanelDetail Installing Bottom Rear Panel Start UP / Operation Start UPStocking Load LimitsSmbt This is an NSF-7 Do not Destroy Do Not Use 41F 0420057B 4MAINTENANCE Clean and sanitize according to Health Code requirements Cleaning ANTI-REFLECTIVE Glass Disconnect fan from wiring harness ServiceReplacing FAN Motors and Blades Canopy Fixture Removing Polycarbonate Lamp CoversRail Fixture Replacing Fluorescent Lamps Electrical Service ReceptaclesReplacing Lamp Holders and END Caps Replacing Electronic Ballast Lamp BallastReplacing Cylinders Single Pane Glass Cylinder Removal ToolSet Screw Locations Replacing Glass Hand Grip Hinge HardwareRepairing Aluminum Coil Technique

P/N 0420057_B specifications

The Hussman P/N 0420057_B represents a cutting-edge refrigeration solution designed for modern retail environments, particularly those requiring efficient display systems for perishable goods. As part of Hussman's extensive product lineup, this unit integrates advanced technologies tailored to enhance both performance and energy efficiency.

One of the standout features of the 0420057_B is its state-of-the-art refrigeration system, which employs a combination of environmentally friendly refrigerants and high-efficiency compressors. This design not only supports compliance with stringent environmental regulations but also contributes to reduced energy consumption, ultimately leading to lower operational costs for retailers. The unit is built to maintain consistent temperatures, ensuring that products are stored and displayed at optimal conditions, thus prolonging freshness and quality.

Another key characteristic of the Hussman P/N 0420057_B is its user-friendly interface. Retail staff can easily monitor and adjust temperature settings, ensuring that the display conditions meet specific product requirements. This feature enhances operational efficiency and minimizes the risk of temperature-related spoilage. Additionally, digital temperature controls come equipped with alarms that alert staff to any fluctuations, acting as a safeguard for perishable inventory.

The design of the unit emphasizes practicality and aesthetics. With a sleek, modern appearance, the 0420057_B fits seamlessly into various store layouts while maximizing product visibility. The glass door design allows for enhanced product presentation, attracting customers and facilitating easy access for quick purchasing decisions.

Durability is a crucial characteristic of Hussman products, and the 0420057_B is no exception. Constructed from high-quality materials, this refrigeration unit is designed to withstand the rigors of daily retail operations. The robust build ensures longevity, reducing maintenance frequency and operational downtimes, which are critical aspects for retailers aiming to enhance their profit margins.

Moreover, the Hussman P/N 0420057_B incorporates intelligent technology, such as smart sensors that optimize energy use based on real-time conditions. This capability not only enhances energy efficiency but also supports retailers in meeting sustainability goals, making this unit a valuable addition to any eco-conscious business strategy.

In conclusion, the Hussman P/N 0420057_B is a versatile refrigeration solution that combines advanced technology, user-friendly features, and sleek design to meet the demanding needs of modern retail environments. Its focus on energy efficiency, durability, and optimal product preservation makes it an essential investment for retailers looking to enhance their operational effectiveness while ensuring customer satisfaction.