hussman P/N 0420057_B operation manual 12INSTALLATION

Page 18

1-12INSTALLATION

Case

Wireway Receptacle

Harness

Route Communication Cable to Junction Box as shown. Coil excess cable in Junction Box.

Mount Junction Box at this location when scale stand is mounted at Center Mullion.

Communication Cable

6.NOTE: RECEPTACLE HARNESS WIRING MUST HAVE

INSULATION SLEEVE INSTALLED PRIOR TO ROUTING.

Leaving about 12 inches of harness hang out of case, route receptacle harness wiring from the 3/4-in. bushing, down the LH upright wireway through hole and into case wireway.

NOTE: COMMUNICATION CABLE WIRING CAN BE ROUTED SIMILARLY.

7.Install the rear door center trim with 3/4-in. bushing by routing wire harness through 3/4-in. bushing and attach with #8 truss head screws.

8.Reposition top over rear door center trim and attach using #8 truss head screws.

9.Reposition scale stand and attach using #8 truss head screws.

10.Install scale stand upright cover with #8 blunt tip sheet metal screws.

Some stores specify an isolated ground for scale stand convenience outlets. If required, apply the following:

Isolated ground sticker to scale stand.

Isolated ground tag to ground wire in case wireway.

11.Connect wiring to power in wireway.

12.Restore power. Check for proper operation.

P/N 0420057_B

U.S. & Canada 1-800-922-1919 • Mexico 1-800-522-1900 • WWW.HUSSMANN.COM

Image 18
Contents Service Merchandisers Page Contents Revision B ServiceWarranty Revision History Ansi Z535.5 DefinitionsSafety Service MerchandisersIf in doubt, do not Enter and inform the client Installation NSF CertificationLocation Exterior Loading Merchandisers Shipped With END InstalledShipping Damage Shipping BracesCase Leveling PreparationLeveler Adjustment Raise LowerGlass Positioning Adjustment Bolt Optional Flexible Wiper Gasket0420057B Installing Coil Cover and Drip Tray Joining InstructionsDrip Tray Connector Drip Tube Installing Optional Wrap BoardReplace wireway cover Restore power Installing Optional Scale Stand 12INSTALLATION Refrigerant Piping Refrigeration / ElectricalRefrigerant Connection LocationSuction Line Control SettingsInsulation Liquid LineRefrigeration Thermostat Defrost Termination ThermostatMerchandiser Electrical Data Field WiringIdentification of Wiring Electrical ConnectionsInstalling Drip Piping Drip Piping and SplashguardsWaste Outlet and Water Seal Installing Splashguard and Lower Front Panel To Install Lower Front PanelDetail Installing Bottom Rear Panel Stocking Start UP / OperationStart UP Load LimitsSmbt This is an NSF-7 Do not Destroy Do Not Use 41F 0420057B 4MAINTENANCE Clean and sanitize according to Health Code requirements Cleaning ANTI-REFLECTIVE Glass Service Disconnect fan from wiring harnessReplacing FAN Motors and Blades Removing Polycarbonate Lamp Covers Canopy FixtureRail Fixture Electrical Service Receptacles Replacing Fluorescent LampsReplacing Lamp Holders and END Caps Replacing Electronic Ballast Lamp BallastReplacing Cylinders Single Pane Glass Cylinder Removal ToolSet Screw Locations Replacing Glass Hand Grip Hinge HardwareRepairing Aluminum Coil Technique

P/N 0420057_B specifications

The Hussman P/N 0420057_B represents a cutting-edge refrigeration solution designed for modern retail environments, particularly those requiring efficient display systems for perishable goods. As part of Hussman's extensive product lineup, this unit integrates advanced technologies tailored to enhance both performance and energy efficiency.

One of the standout features of the 0420057_B is its state-of-the-art refrigeration system, which employs a combination of environmentally friendly refrigerants and high-efficiency compressors. This design not only supports compliance with stringent environmental regulations but also contributes to reduced energy consumption, ultimately leading to lower operational costs for retailers. The unit is built to maintain consistent temperatures, ensuring that products are stored and displayed at optimal conditions, thus prolonging freshness and quality.

Another key characteristic of the Hussman P/N 0420057_B is its user-friendly interface. Retail staff can easily monitor and adjust temperature settings, ensuring that the display conditions meet specific product requirements. This feature enhances operational efficiency and minimizes the risk of temperature-related spoilage. Additionally, digital temperature controls come equipped with alarms that alert staff to any fluctuations, acting as a safeguard for perishable inventory.

The design of the unit emphasizes practicality and aesthetics. With a sleek, modern appearance, the 0420057_B fits seamlessly into various store layouts while maximizing product visibility. The glass door design allows for enhanced product presentation, attracting customers and facilitating easy access for quick purchasing decisions.

Durability is a crucial characteristic of Hussman products, and the 0420057_B is no exception. Constructed from high-quality materials, this refrigeration unit is designed to withstand the rigors of daily retail operations. The robust build ensures longevity, reducing maintenance frequency and operational downtimes, which are critical aspects for retailers aiming to enhance their profit margins.

Moreover, the Hussman P/N 0420057_B incorporates intelligent technology, such as smart sensors that optimize energy use based on real-time conditions. This capability not only enhances energy efficiency but also supports retailers in meeting sustainability goals, making this unit a valuable addition to any eco-conscious business strategy.

In conclusion, the Hussman P/N 0420057_B is a versatile refrigeration solution that combines advanced technology, user-friendly features, and sleek design to meet the demanding needs of modern retail environments. Its focus on energy efficiency, durability, and optimal product preservation makes it an essential investment for retailers looking to enhance their operational effectiveness while ensuring customer satisfaction.