hussman P/N 0420057_B operation manual Replacing Glass Hand Grip, Hinge Hardware

Page 43

P/N 0420057_B

REPLACING GLASS HAND GRIP

The hand grip is fastened to the curved glass as shown below. A 2 inch (51 mm) bead of silicone needs to be placed 3 inches (76 mm) from each end and in the center of the hand grip. The duct tape is placed on the glass to provide a tight fit.

6-7

Type: Two cylinders and three fastening points. P/N 0407352

Used on: 30° outside wedge.

Duct Tape

Glass

3/8 in. (10 mm) of Duct Tape on Each Side of Bottom Edge of Glass

3/8 in. (10 mm)

Type: Three cylinders and four fastening points. P/N 0412538

Used on 90° inside wedge, 45° outside and inside wedge, 30° inside wedge.

 

Start 2 in. (51 mm)

 

Silicone Bead

3 in.

3 in. (76 mm)

(76 mm)

From Each End

 

Glass Grip

Note: This hinge assembly, when used on the 90° and 45° inside wedge, uses only two cylinders.

HINGE HARDWARE

Type: Two cylinders and one fastening point. P/N 0401884

Used on: 8 ft and 12 ft (2438 mm and 3658 mm) parent cases and as a joining bracket.

Type: Four cylinders and five fastening points. P/N 0413170

Used On: 90° outside wedge.

HUSSMANN CORPORATION, Bridgeton, MO 63044-2483 U.S.A.

Service Merchandisers

Image 43
Contents Service Merchandisers Page Contents Ansi Z535.5 Definitions ServiceWarranty Revision History Revision BService Merchandisers SafetyIf in doubt, do not Enter and inform the client NSF Certification InstallationLocation Shipping Braces Merchandisers Shipped With END InstalledShipping Damage Exterior LoadingPreparation Case LevelingRaise Lower Leveler AdjustmentGlass Positioning Optional Flexible Wiper Gasket Adjustment Bolt0420057B Joining Instructions Installing Coil Cover and Drip TrayInstalling Optional Wrap Board Drip Tray Connector Drip TubeReplace wireway cover Restore power Installing Optional Scale Stand 12INSTALLATION Connection Location Refrigeration / ElectricalRefrigerant Refrigerant PipingLiquid Line Control SettingsInsulation Suction LineDefrost Termination Thermostat Refrigeration ThermostatElectrical Connections Field WiringIdentification of Wiring Merchandiser Electrical DataDrip Piping and Splashguards Installing Drip PipingWaste Outlet and Water Seal To Install Lower Front Panel Installing Splashguard and Lower Front PanelDetail Installing Bottom Rear Panel Load Limits Start UP / OperationStart UP StockingSmbt This is an NSF-7 Do not Destroy Do Not Use 41F 0420057B 4MAINTENANCE Clean and sanitize according to Health Code requirements Cleaning ANTI-REFLECTIVE Glass Disconnect fan from wiring harness ServiceReplacing FAN Motors and Blades Canopy Fixture Removing Polycarbonate Lamp CoversRail Fixture Replacing Fluorescent Lamps Electrical Service ReceptaclesReplacing Lamp Holders and END Caps Lamp Ballast Replacing Electronic BallastCylinder Removal Tool Replacing Cylinders Single Pane GlassSet Screw Locations Hinge Hardware Replacing Glass Hand GripTechnique Repairing Aluminum Coil

P/N 0420057_B specifications

The Hussman P/N 0420057_B represents a cutting-edge refrigeration solution designed for modern retail environments, particularly those requiring efficient display systems for perishable goods. As part of Hussman's extensive product lineup, this unit integrates advanced technologies tailored to enhance both performance and energy efficiency.

One of the standout features of the 0420057_B is its state-of-the-art refrigeration system, which employs a combination of environmentally friendly refrigerants and high-efficiency compressors. This design not only supports compliance with stringent environmental regulations but also contributes to reduced energy consumption, ultimately leading to lower operational costs for retailers. The unit is built to maintain consistent temperatures, ensuring that products are stored and displayed at optimal conditions, thus prolonging freshness and quality.

Another key characteristic of the Hussman P/N 0420057_B is its user-friendly interface. Retail staff can easily monitor and adjust temperature settings, ensuring that the display conditions meet specific product requirements. This feature enhances operational efficiency and minimizes the risk of temperature-related spoilage. Additionally, digital temperature controls come equipped with alarms that alert staff to any fluctuations, acting as a safeguard for perishable inventory.

The design of the unit emphasizes practicality and aesthetics. With a sleek, modern appearance, the 0420057_B fits seamlessly into various store layouts while maximizing product visibility. The glass door design allows for enhanced product presentation, attracting customers and facilitating easy access for quick purchasing decisions.

Durability is a crucial characteristic of Hussman products, and the 0420057_B is no exception. Constructed from high-quality materials, this refrigeration unit is designed to withstand the rigors of daily retail operations. The robust build ensures longevity, reducing maintenance frequency and operational downtimes, which are critical aspects for retailers aiming to enhance their profit margins.

Moreover, the Hussman P/N 0420057_B incorporates intelligent technology, such as smart sensors that optimize energy use based on real-time conditions. This capability not only enhances energy efficiency but also supports retailers in meeting sustainability goals, making this unit a valuable addition to any eco-conscious business strategy.

In conclusion, the Hussman P/N 0420057_B is a versatile refrigeration solution that combines advanced technology, user-friendly features, and sleek design to meet the demanding needs of modern retail environments. Its focus on energy efficiency, durability, and optimal product preservation makes it an essential investment for retailers looking to enhance their operational effectiveness while ensuring customer satisfaction.