hussman P/N 0420057_B Shipping Damage, Exterior Loading, Merchandisers Shipped With END Installed

Page 8

1-2INSTALLATION

NOTICE

Do NOT remove shipping braces until the merchandisers are positioned for installation. Frames may be damaged.

SHIPPING DAMAGE

All equipment should be thoroughly examined for shipping damage before and during unload- ing. This equipment has been carefully inspected at our factory. Any claim for loss or damage must be made to the carrier. The carrier will provide any necessary inspection reports and/or claim forms.

Apparent Loss or Damage

If there is an obvious loss or damage, it must be noted on the freight bill or express receipt and signed by the carrier’s agent; otherwise, carrier may refuse claim.

Concealed Loss or Damage

When loss or damage is not apparent until after equipment is uncrated, retain all packing materi- als and submit a written request to the carrier for inspection, within 15 days.

!WARNING

Do not stand or walk on top of case

because falling off could

cause serious personal injury.

EXTERIOR LOADING

Do NOT walk on top of merchandisers or damage to the merchandisers and serious person- al injury could occur. Merchandisers ARE NOT

STRUCTURALLY DESIGNED TO SUPPORT EXCESSIVE

EXTERNAL LOADING such as the weight of a person. Do not place heavy objects on the case.

MERCHANDISERS SHIPPED

WITH END INSTALLED

If the case was shipped with the end installed, two long bolts were used to hold the shipping brace to the end. If the shipping bolts are re- inserted after removing the brace, they will extend into the product area. Therefore, be sure to replace these bolts with the shorter bolts provided. Refer to the detailed information provided in the separate End Kit Instruction shipped with each end.

Note: Be careful not to damage the factory installed end while moving the case. Make sure that tools are positioned past the end and beneath the merchandiser’s support bar.

SHIPPING BRACES

Move the fixture as close as possible to its per- manent location and then remove all packaging and shipping braces. Check for damage before discarding packaging. Remove all separately packed accessories such as kits, and shelves.

Remove all nut retainers used with shipping braces. NSF certification requires the use of ANSI Standard nuts and bolts with not more than two (2) threads showing after installation.

SHIPPING RIDER

Each case is shipped on a rider to protect factory-installed legs, and to make positioning the case easier. Remove the rider after the case has been positioned.

Note: Once the rider is removed, the case must be lifted –NOT PUSHED– to reposition.

P/N 0420057_B

U.S. & Canada 1-800-922-1919 • Mexico 1-800-522-1900 • WWW.HUSSMANN.COM

Image 8
Contents Service Merchandisers Page Contents Service Warranty Revision HistoryRevision B Ansi Z535.5 DefinitionsSafety Service MerchandisersIf in doubt, do not Enter and inform the client Location InstallationNSF Certification Merchandisers Shipped With END Installed Shipping DamageExterior Loading Shipping BracesCase Leveling PreparationLeveler Adjustment Raise LowerGlass Positioning Adjustment Bolt Optional Flexible Wiper Gasket0420057B Installing Coil Cover and Drip Tray Joining InstructionsDrip Tray Connector Drip Tube Installing Optional Wrap BoardReplace wireway cover Restore power Installing Optional Scale Stand 12INSTALLATION Refrigeration / Electrical RefrigerantRefrigerant Piping Connection LocationControl Settings InsulationSuction Line Liquid LineRefrigeration Thermostat Defrost Termination ThermostatField Wiring Identification of WiringMerchandiser Electrical Data Electrical ConnectionsWaste Outlet and Water Seal Installing Drip PipingDrip Piping and Splashguards Installing Splashguard and Lower Front Panel To Install Lower Front PanelDetail Installing Bottom Rear Panel Start UP / Operation Start UPStocking Load LimitsSmbt This is an NSF-7 Do not Destroy Do Not Use 41F 0420057B 4MAINTENANCE Clean and sanitize according to Health Code requirements Cleaning ANTI-REFLECTIVE Glass Replacing FAN Motors and Blades ServiceDisconnect fan from wiring harness Rail Fixture Removing Polycarbonate Lamp CoversCanopy Fixture Replacing Lamp Holders and END Caps Electrical Service ReceptaclesReplacing Fluorescent Lamps Replacing Electronic Ballast Lamp BallastReplacing Cylinders Single Pane Glass Cylinder Removal ToolSet Screw Locations Replacing Glass Hand Grip Hinge HardwareRepairing Aluminum Coil Technique

P/N 0420057_B specifications

The Hussman P/N 0420057_B represents a cutting-edge refrigeration solution designed for modern retail environments, particularly those requiring efficient display systems for perishable goods. As part of Hussman's extensive product lineup, this unit integrates advanced technologies tailored to enhance both performance and energy efficiency.

One of the standout features of the 0420057_B is its state-of-the-art refrigeration system, which employs a combination of environmentally friendly refrigerants and high-efficiency compressors. This design not only supports compliance with stringent environmental regulations but also contributes to reduced energy consumption, ultimately leading to lower operational costs for retailers. The unit is built to maintain consistent temperatures, ensuring that products are stored and displayed at optimal conditions, thus prolonging freshness and quality.

Another key characteristic of the Hussman P/N 0420057_B is its user-friendly interface. Retail staff can easily monitor and adjust temperature settings, ensuring that the display conditions meet specific product requirements. This feature enhances operational efficiency and minimizes the risk of temperature-related spoilage. Additionally, digital temperature controls come equipped with alarms that alert staff to any fluctuations, acting as a safeguard for perishable inventory.

The design of the unit emphasizes practicality and aesthetics. With a sleek, modern appearance, the 0420057_B fits seamlessly into various store layouts while maximizing product visibility. The glass door design allows for enhanced product presentation, attracting customers and facilitating easy access for quick purchasing decisions.

Durability is a crucial characteristic of Hussman products, and the 0420057_B is no exception. Constructed from high-quality materials, this refrigeration unit is designed to withstand the rigors of daily retail operations. The robust build ensures longevity, reducing maintenance frequency and operational downtimes, which are critical aspects for retailers aiming to enhance their profit margins.

Moreover, the Hussman P/N 0420057_B incorporates intelligent technology, such as smart sensors that optimize energy use based on real-time conditions. This capability not only enhances energy efficiency but also supports retailers in meeting sustainability goals, making this unit a valuable addition to any eco-conscious business strategy.

In conclusion, the Hussman P/N 0420057_B is a versatile refrigeration solution that combines advanced technology, user-friendly features, and sleek design to meet the demanding needs of modern retail environments. Its focus on energy efficiency, durability, and optimal product preservation makes it an essential investment for retailers looking to enhance their operational effectiveness while ensuring customer satisfaction.