hussman P/N 0420057_B operation manual Do Not Use

Page 31

P/N 0420057_B

5-1

MAINTENANCE

CARE AND CLEANING

Long life and satisfactory performance of any equipment is dependent upon the care it receives. To ensure long life, proper sanitation and minimum maintenance costs, these mer- chandisers should be thoroughly cleaned, all debris removed and the interiors washed down, at least weekly.

Exterior Surfaces

The exterior surfaces must be cleaned with a mild domestic detergent and warm water to protect and maintain their attractive finish.

NEVER USE ABRASIVE CLEANERS OR SCOURING PADS. DO NOT USE AMMONIA BASED CLEANERS ON ACRYLIC PARTS.

Interior Surfaces

The interior surfaces may be cleaned with most domestic detergents, ammonia based cleaners and sanitizing solutions with no harm to the surface. Removable parts are labeled REMOVE

FOR CLEANING.

Removable stainless steel parts may be cleaned and sanitized in dishwasher.

See next page for detailed direction.

NOTICE

Product will be degraded

and may spoil if allowed to sit

in a non-refrigerated area.

!CAUTION

Do NOT use HOT water on COLD glass surfaces. This can cause the glass to shatter and could result in personal injury. Allow glass fronts, ends, and service doors to warm before applying hot water.

! WARNING

Prevent injury.

ALWAYS SHUT POWER OFF

during cleaning process.

Do Not Use:

•Abrasive cleansers and scouring pads, as these will mar the finish.

•A hose on lighted shelves or submerge the shelves in water.

•Solvent, oil or acidic based cleaners on any interior surfaces.

Do:

•Remove the product and all loose debris to avoid clogging the waste outlet.

•Store product in a refrigerated area such as a cooler. Remove only as much product as can be taken to the cooler in a timely manner.

•Turn off refrigeration, then disconnect electrical power.

•Thoroughly clean all surfaces with mild detergent and water (105 to 140°F / 40 to

60°C). DO NOT USE STEAM OR HIGH WATER

PRESSURE HOSES TO WASH THE INTERIOR.

THESE WILL DESTROY THE MERCHANDISER’S LINER AND SEALS CAUSING LEAKS AND POOR PERFORMANCE.

•Lift or remove fan plenum for cleaning. Hook chain in rear panel to secure plenum during cleaning. Be sure to reposition the fan plenum after cleaning merchandiser.

•Take care to minimize direct contact between fan motors and cleaning or rinse water.

•Rinse with water, but do NOT flood. NEVER

INTRODUCE WATER FASTER THAN THE WASTE OUTLET CAN REMOVE IT.

•Allow merchandisers to dry before resuming operation.

•After cleaning is completed, turn on power to the merchandiser.

HUSSMANN CORPORATION, Bridgeton, MO 63044-2483 U.S.A.

Service Merchandisers

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Service Merchandisers Page Contents Ansi Z535.5 Definitions ServiceWarranty Revision History Revision BService Merchandisers SafetyIf in doubt, do not Enter and inform the client NSF Certification InstallationLocation Shipping Braces Merchandisers Shipped With END InstalledShipping Damage Exterior LoadingPreparation Case LevelingRaise Lower Leveler AdjustmentGlass Positioning Optional Flexible Wiper Gasket Adjustment Bolt0420057B Joining Instructions Installing Coil Cover and Drip TrayInstalling Optional Wrap Board Drip Tray Connector Drip TubeReplace wireway cover Restore power Installing Optional Scale Stand 12INSTALLATION Connection Location Refrigeration / ElectricalRefrigerant Refrigerant PipingLiquid Line Control SettingsInsulation Suction LineDefrost Termination Thermostat Refrigeration ThermostatElectrical Connections Field WiringIdentification of Wiring Merchandiser Electrical DataDrip Piping and Splashguards Installing Drip PipingWaste Outlet and Water Seal To Install Lower Front Panel Installing Splashguard and Lower Front PanelDetail Installing Bottom Rear Panel Load Limits Start UP / OperationStart UP StockingSmbt This is an NSF-7 Do not Destroy Do Not Use 41F 0420057B 4MAINTENANCE Clean and sanitize according to Health Code requirements Cleaning ANTI-REFLECTIVE Glass Disconnect fan from wiring harness ServiceReplacing FAN Motors and Blades Canopy Fixture Removing Polycarbonate Lamp CoversRail Fixture Replacing Fluorescent Lamps Electrical Service ReceptaclesReplacing Lamp Holders and END Caps Lamp Ballast Replacing Electronic BallastCylinder Removal Tool Replacing Cylinders Single Pane GlassSet Screw Locations Hinge Hardware Replacing Glass Hand GripTechnique Repairing Aluminum Coil

P/N 0420057_B specifications

The Hussman P/N 0420057_B represents a cutting-edge refrigeration solution designed for modern retail environments, particularly those requiring efficient display systems for perishable goods. As part of Hussman's extensive product lineup, this unit integrates advanced technologies tailored to enhance both performance and energy efficiency.

One of the standout features of the 0420057_B is its state-of-the-art refrigeration system, which employs a combination of environmentally friendly refrigerants and high-efficiency compressors. This design not only supports compliance with stringent environmental regulations but also contributes to reduced energy consumption, ultimately leading to lower operational costs for retailers. The unit is built to maintain consistent temperatures, ensuring that products are stored and displayed at optimal conditions, thus prolonging freshness and quality.

Another key characteristic of the Hussman P/N 0420057_B is its user-friendly interface. Retail staff can easily monitor and adjust temperature settings, ensuring that the display conditions meet specific product requirements. This feature enhances operational efficiency and minimizes the risk of temperature-related spoilage. Additionally, digital temperature controls come equipped with alarms that alert staff to any fluctuations, acting as a safeguard for perishable inventory.

The design of the unit emphasizes practicality and aesthetics. With a sleek, modern appearance, the 0420057_B fits seamlessly into various store layouts while maximizing product visibility. The glass door design allows for enhanced product presentation, attracting customers and facilitating easy access for quick purchasing decisions.

Durability is a crucial characteristic of Hussman products, and the 0420057_B is no exception. Constructed from high-quality materials, this refrigeration unit is designed to withstand the rigors of daily retail operations. The robust build ensures longevity, reducing maintenance frequency and operational downtimes, which are critical aspects for retailers aiming to enhance their profit margins.

Moreover, the Hussman P/N 0420057_B incorporates intelligent technology, such as smart sensors that optimize energy use based on real-time conditions. This capability not only enhances energy efficiency but also supports retailers in meeting sustainability goals, making this unit a valuable addition to any eco-conscious business strategy.

In conclusion, the Hussman P/N 0420057_B is a versatile refrigeration solution that combines advanced technology, user-friendly features, and sleek design to meet the demanding needs of modern retail environments. Its focus on energy efficiency, durability, and optimal product preservation makes it an essential investment for retailers looking to enhance their operational effectiveness while ensuring customer satisfaction.
Top Page Image Contents