hussman P/N 0420057_B operation manual Case Leveling, Preparation

Page 9

P/N 0420057_B

1-3

Cross-Members

Sides

 

Screws

 

(each leg)

 

Shipping Rider

Screws

(two each end

for 8 ft Case

of each

 

cross-member)

Leg

To remove the rider, remove screws attaching each leg to rider. Remove screws holding rider cross-members, then slide cross-members out from between sides. Once cross-members are out, slide the sides out.

CASE LEVELING

Merchandisers must be installed level to ensure proper operation of the refrigeration system and to ensure proper drainage of defrost water.

During all steps of setting, joining and leveling cases, close attention to glass position and operation must be maintained. Please review all steps and photos before making any adjust- ments. DO NOT make any glass adjustments until individual case is set and level.

Preparation

1.Using store blueprints, measure off and mark on floor the exact dimensions/locations of the case footprint.

2.Snap a chalk line for the front and rear positions of the base legs.

3.Mark the location of each joint from front to back lines.

4.FLOORS ARE NOT LEVEL!!! When working with two or more cases to be joined, the whole lineup must be leveled on the same plane, left to right and front to back. This means that the entire lineup must be brought up to the level of the highest case in the lineup.

Along the lines previously marked, find the highest point of the floor by:

Walking the floor and noticing any dips or mounds;

Using a string level; and

Using a transit.

HUSSMANN CORPORATION, Bridgeton, MO 63044-2483 U.S.A.

Service Merchandisers

Image 9
Contents Service Merchandisers Page Contents Warranty Revision History ServiceRevision B Ansi Z535.5 DefinitionsService Merchandisers SafetyIf in doubt, do not Enter and inform the client Installation NSF CertificationLocation Shipping Damage Merchandisers Shipped With END InstalledExterior Loading Shipping BracesPreparation Case LevelingRaise Lower Leveler AdjustmentGlass Positioning Optional Flexible Wiper Gasket Adjustment Bolt0420057B Joining Instructions Installing Coil Cover and Drip TrayInstalling Optional Wrap Board Drip Tray Connector Drip TubeReplace wireway cover Restore power Installing Optional Scale Stand 12INSTALLATION Refrigerant Refrigeration / ElectricalRefrigerant Piping Connection LocationInsulation Control SettingsSuction Line Liquid LineDefrost Termination Thermostat Refrigeration ThermostatIdentification of Wiring Field WiringMerchandiser Electrical Data Electrical ConnectionsInstalling Drip Piping Drip Piping and SplashguardsWaste Outlet and Water Seal To Install Lower Front Panel Installing Splashguard and Lower Front PanelDetail Installing Bottom Rear Panel Start UP Start UP / OperationStocking Load LimitsSmbt This is an NSF-7 Do not Destroy Do Not Use 41F 0420057B 4MAINTENANCE Clean and sanitize according to Health Code requirements Cleaning ANTI-REFLECTIVE Glass Service Disconnect fan from wiring harnessReplacing FAN Motors and Blades Removing Polycarbonate Lamp Covers Canopy FixtureRail Fixture Electrical Service Receptacles Replacing Fluorescent LampsReplacing Lamp Holders and END Caps Lamp Ballast Replacing Electronic BallastCylinder Removal Tool Replacing Cylinders Single Pane GlassSet Screw Locations Hinge Hardware Replacing Glass Hand GripTechnique Repairing Aluminum Coil

P/N 0420057_B specifications

The Hussman P/N 0420057_B represents a cutting-edge refrigeration solution designed for modern retail environments, particularly those requiring efficient display systems for perishable goods. As part of Hussman's extensive product lineup, this unit integrates advanced technologies tailored to enhance both performance and energy efficiency.

One of the standout features of the 0420057_B is its state-of-the-art refrigeration system, which employs a combination of environmentally friendly refrigerants and high-efficiency compressors. This design not only supports compliance with stringent environmental regulations but also contributes to reduced energy consumption, ultimately leading to lower operational costs for retailers. The unit is built to maintain consistent temperatures, ensuring that products are stored and displayed at optimal conditions, thus prolonging freshness and quality.

Another key characteristic of the Hussman P/N 0420057_B is its user-friendly interface. Retail staff can easily monitor and adjust temperature settings, ensuring that the display conditions meet specific product requirements. This feature enhances operational efficiency and minimizes the risk of temperature-related spoilage. Additionally, digital temperature controls come equipped with alarms that alert staff to any fluctuations, acting as a safeguard for perishable inventory.

The design of the unit emphasizes practicality and aesthetics. With a sleek, modern appearance, the 0420057_B fits seamlessly into various store layouts while maximizing product visibility. The glass door design allows for enhanced product presentation, attracting customers and facilitating easy access for quick purchasing decisions.

Durability is a crucial characteristic of Hussman products, and the 0420057_B is no exception. Constructed from high-quality materials, this refrigeration unit is designed to withstand the rigors of daily retail operations. The robust build ensures longevity, reducing maintenance frequency and operational downtimes, which are critical aspects for retailers aiming to enhance their profit margins.

Moreover, the Hussman P/N 0420057_B incorporates intelligent technology, such as smart sensors that optimize energy use based on real-time conditions. This capability not only enhances energy efficiency but also supports retailers in meeting sustainability goals, making this unit a valuable addition to any eco-conscious business strategy.

In conclusion, the Hussman P/N 0420057_B is a versatile refrigeration solution that combines advanced technology, user-friendly features, and sleek design to meet the demanding needs of modern retail environments. Its focus on energy efficiency, durability, and optimal product preservation makes it an essential investment for retailers looking to enhance their operational effectiveness while ensuring customer satisfaction.