hussman P/N 0420057_B operation manual Installation, NSF Certification, Location

Page 7

P/N 0420057_B

1-1

INSTALLATION

NSF CERTIFICATION

These merchandisers are manufactured to meet ANSI / National Sanitation Foundation (NSF®) Standard #7 requirements. Proper installation is required to maintain certification. Near the serial plate, each case carries a label identifying the type of application for which the case was certi- fied.

ANSI/NSF-7 Type I – Display Refrigerator / Freezer Intended for 75°F / 55%RH Ambient Application

ANSI/NSF-7 Type II – Display Refrigerator / Freezer Intended for 80°F / 55%RH Ambient Application

ANSI/NSF-7 – Display Refrigerator

Intended for Bulk Produce

LOCATION

These merchandisers are designed for displaying products in air conditioned stores where tempera- ture is maintained at or below the ANSI/NSF-7 specified level and relative humidity is main- tained at or below 55%.

Placing refrigerated merchandisers in direct sun- light, near hot tables or near other heat sources could impair their efficiency.

Like other merchandisers, these are sensitive to air disturbances. Air currents passing around merchandisers will seriously impair their opera- tion. Do NOT allow air conditioning, electric fans, open doors or windows, etc. to create air currents around the merchandisers.

Product should always be maintained at proper temperature. This means that from the time the product is received, through storage, preparation and display, the temperature of the product must be controlled to maximize the life of the product.

!CAUTION

Read before raising front glass to prevent

injury from broken or falling glass.

The top cylinders, which allow the raising and lowering of this glass, have been carefully installed and tested for the proper tension before shipment. However, during shipment and stor- age, the lubricant inside the cylinders may have settled. This settling can cause excessive or uneven tension on the glass to the point of breakage.

To avoid any damage, please do the follow- ing before completely raising the front glass.

1.Slowly raise and lower each glass section 6 times to a height of 6 in. (152 mm).

2.Increase the height to about 12 in. (305 mm) and raise and lower the glass 6 times.

3.Then raise the glass to the full extension and lower.

This should release any settled lubricant in the cylinders and prevent any stress on the front glass.

Leveling and adjustment procedures begin on

Page 1-3.

6 in.

6 in.

HUSSMANN CORPORATION, Bridgeton, MO 63044-2483 U.S.A.

Service Merchandisers

Image 7
Contents Service Merchandisers Page Contents Ansi Z535.5 Definitions ServiceWarranty Revision History Revision BService Merchandisers SafetyIf in doubt, do not Enter and inform the client NSF Certification InstallationLocation Shipping Braces Merchandisers Shipped With END InstalledShipping Damage Exterior LoadingPreparation Case LevelingRaise Lower Leveler AdjustmentGlass Positioning Optional Flexible Wiper Gasket Adjustment Bolt0420057B Joining Instructions Installing Coil Cover and Drip TrayInstalling Optional Wrap Board Drip Tray Connector Drip TubeReplace wireway cover Restore power Installing Optional Scale Stand 12INSTALLATION Connection Location Refrigeration / ElectricalRefrigerant Refrigerant PipingLiquid Line Control SettingsInsulation Suction LineDefrost Termination Thermostat Refrigeration ThermostatElectrical Connections Field WiringIdentification of Wiring Merchandiser Electrical DataDrip Piping and Splashguards Installing Drip PipingWaste Outlet and Water Seal To Install Lower Front Panel Installing Splashguard and Lower Front PanelDetail Installing Bottom Rear Panel Load Limits Start UP / OperationStart UP StockingSmbt This is an NSF-7 Do not Destroy Do Not Use 41F 0420057B 4MAINTENANCE Clean and sanitize according to Health Code requirements Cleaning ANTI-REFLECTIVE Glass Disconnect fan from wiring harness ServiceReplacing FAN Motors and Blades Canopy Fixture Removing Polycarbonate Lamp CoversRail Fixture Replacing Fluorescent Lamps Electrical Service ReceptaclesReplacing Lamp Holders and END Caps Lamp Ballast Replacing Electronic BallastCylinder Removal Tool Replacing Cylinders Single Pane GlassSet Screw Locations Hinge Hardware Replacing Glass Hand GripTechnique Repairing Aluminum Coil

P/N 0420057_B specifications

The Hussman P/N 0420057_B represents a cutting-edge refrigeration solution designed for modern retail environments, particularly those requiring efficient display systems for perishable goods. As part of Hussman's extensive product lineup, this unit integrates advanced technologies tailored to enhance both performance and energy efficiency.

One of the standout features of the 0420057_B is its state-of-the-art refrigeration system, which employs a combination of environmentally friendly refrigerants and high-efficiency compressors. This design not only supports compliance with stringent environmental regulations but also contributes to reduced energy consumption, ultimately leading to lower operational costs for retailers. The unit is built to maintain consistent temperatures, ensuring that products are stored and displayed at optimal conditions, thus prolonging freshness and quality.

Another key characteristic of the Hussman P/N 0420057_B is its user-friendly interface. Retail staff can easily monitor and adjust temperature settings, ensuring that the display conditions meet specific product requirements. This feature enhances operational efficiency and minimizes the risk of temperature-related spoilage. Additionally, digital temperature controls come equipped with alarms that alert staff to any fluctuations, acting as a safeguard for perishable inventory.

The design of the unit emphasizes practicality and aesthetics. With a sleek, modern appearance, the 0420057_B fits seamlessly into various store layouts while maximizing product visibility. The glass door design allows for enhanced product presentation, attracting customers and facilitating easy access for quick purchasing decisions.

Durability is a crucial characteristic of Hussman products, and the 0420057_B is no exception. Constructed from high-quality materials, this refrigeration unit is designed to withstand the rigors of daily retail operations. The robust build ensures longevity, reducing maintenance frequency and operational downtimes, which are critical aspects for retailers aiming to enhance their profit margins.

Moreover, the Hussman P/N 0420057_B incorporates intelligent technology, such as smart sensors that optimize energy use based on real-time conditions. This capability not only enhances energy efficiency but also supports retailers in meeting sustainability goals, making this unit a valuable addition to any eco-conscious business strategy.

In conclusion, the Hussman P/N 0420057_B is a versatile refrigeration solution that combines advanced technology, user-friendly features, and sleek design to meet the demanding needs of modern retail environments. Its focus on energy efficiency, durability, and optimal product preservation makes it an essential investment for retailers looking to enhance their operational effectiveness while ensuring customer satisfaction.