hussman P/N 0420057_B operation manual Installing Optional Scale Stand

Page 17

P/N 0420057_B

Installing Optional Scale Stand

MOA 0458960

1.Turn off power to case.

2.Determine location by positioning the scale stand on the rear of the case between door frames.

3.Using holes in scale stand bracket as a template, mark hole locations on rear and top of case.

4.Remove scale stand. Drill 1/8-inch diameter pilot holes through metal liners at the marked locations.

NOTE: METAL LINERS ARE LESS THAN 1/8-INCH THICK--DO NOT DRILL BEYOND METAL LINERS.

1-11

Screw - SM #8-18 x 3/8

Truss Head

Case Wireway

5.Move top panel away from back of case. Remove center rear door trim and remove LH Upright wireway cover to allow routing of receptacle harness.

Screw - SM #8-18 x 3/8 Truss Head

(3 required)

Insulation in this area to be notched as needed for wire harness routing.

Connect after routing wiring through case.

Isolated Ground Sticker

(If required)

Install strain relief connector where Communication Cable exits scale

3/4 Bushing

LH Upright

Convenience Outlet

stand assembly. Use plug button if Communication Cable i not required.

Wireway

Harness -

Receptacle

Scale Stand Upright Cover

Screw - SM #8-18 x 3/8 Hex Head (2 required)

Rear Door Center Trim

Communication Cable Route cable with 12-in. outside the strain relief connector in the scale stand

HUSSMANN CORPORATION, Bridgeton, MO 63044-2483 U.S.A.

Service Merchandisers

Image 17
Contents Service Merchandisers Page Contents Warranty Revision History ServiceRevision B Ansi Z535.5 DefinitionsService Merchandisers SafetyIf in doubt, do not Enter and inform the client Location InstallationNSF Certification Shipping Damage Merchandisers Shipped With END InstalledExterior Loading Shipping BracesPreparation Case LevelingRaise Lower Leveler AdjustmentGlass Positioning Optional Flexible Wiper Gasket Adjustment Bolt0420057B Joining Instructions Installing Coil Cover and Drip TrayInstalling Optional Wrap Board Drip Tray Connector Drip TubeReplace wireway cover Restore power Installing Optional Scale Stand 12INSTALLATION Refrigerant Refrigeration / ElectricalRefrigerant Piping Connection LocationInsulation Control SettingsSuction Line Liquid LineDefrost Termination Thermostat Refrigeration ThermostatIdentification of Wiring Field WiringMerchandiser Electrical Data Electrical ConnectionsWaste Outlet and Water Seal Installing Drip PipingDrip Piping and Splashguards To Install Lower Front Panel Installing Splashguard and Lower Front PanelDetail Installing Bottom Rear Panel Start UP Start UP / OperationStocking Load LimitsSmbt This is an NSF-7 Do not Destroy Do Not Use 41F 0420057B 4MAINTENANCE Clean and sanitize according to Health Code requirements Cleaning ANTI-REFLECTIVE Glass Replacing FAN Motors and Blades ServiceDisconnect fan from wiring harness Rail Fixture Removing Polycarbonate Lamp CoversCanopy Fixture Replacing Lamp Holders and END Caps Electrical Service ReceptaclesReplacing Fluorescent Lamps Lamp Ballast Replacing Electronic BallastCylinder Removal Tool Replacing Cylinders Single Pane GlassSet Screw Locations Hinge Hardware Replacing Glass Hand GripTechnique Repairing Aluminum Coil

P/N 0420057_B specifications

The Hussman P/N 0420057_B represents a cutting-edge refrigeration solution designed for modern retail environments, particularly those requiring efficient display systems for perishable goods. As part of Hussman's extensive product lineup, this unit integrates advanced technologies tailored to enhance both performance and energy efficiency.

One of the standout features of the 0420057_B is its state-of-the-art refrigeration system, which employs a combination of environmentally friendly refrigerants and high-efficiency compressors. This design not only supports compliance with stringent environmental regulations but also contributes to reduced energy consumption, ultimately leading to lower operational costs for retailers. The unit is built to maintain consistent temperatures, ensuring that products are stored and displayed at optimal conditions, thus prolonging freshness and quality.

Another key characteristic of the Hussman P/N 0420057_B is its user-friendly interface. Retail staff can easily monitor and adjust temperature settings, ensuring that the display conditions meet specific product requirements. This feature enhances operational efficiency and minimizes the risk of temperature-related spoilage. Additionally, digital temperature controls come equipped with alarms that alert staff to any fluctuations, acting as a safeguard for perishable inventory.

The design of the unit emphasizes practicality and aesthetics. With a sleek, modern appearance, the 0420057_B fits seamlessly into various store layouts while maximizing product visibility. The glass door design allows for enhanced product presentation, attracting customers and facilitating easy access for quick purchasing decisions.

Durability is a crucial characteristic of Hussman products, and the 0420057_B is no exception. Constructed from high-quality materials, this refrigeration unit is designed to withstand the rigors of daily retail operations. The robust build ensures longevity, reducing maintenance frequency and operational downtimes, which are critical aspects for retailers aiming to enhance their profit margins.

Moreover, the Hussman P/N 0420057_B incorporates intelligent technology, such as smart sensors that optimize energy use based on real-time conditions. This capability not only enhances energy efficiency but also supports retailers in meeting sustainability goals, making this unit a valuable addition to any eco-conscious business strategy.

In conclusion, the Hussman P/N 0420057_B is a versatile refrigeration solution that combines advanced technology, user-friendly features, and sleek design to meet the demanding needs of modern retail environments. Its focus on energy efficiency, durability, and optimal product preservation makes it an essential investment for retailers looking to enhance their operational effectiveness while ensuring customer satisfaction.