Master Bilt TAF-27 ERC2 manual Final Check List, Sensor Probe Temperature and Resistance

Page 13

FINAL CHECK LIST

A.Check operating pressures.

B.Check electrical requirements of unit to supply voltage.

C.Set temperature control for desired temperature range.

D.Check system for proper defrost settings and operation.

E.Check condensing unit for vibrating or rubbing tubing. Dampen and clamp as required.

F.All valves should be completely open counter-clockwise.

G.Check packing nuts on all service valves.

H.Replace all service valve caps and latch unit covers.

SENSOR PROBE

NOTICE: If the probe assembly is disconnected from the main board during normal operation (unit running), the connectors must be installed in the same position that they had before disconnection (P1 and P2), otherwise the control will not function properly.

The Electronic Refrigeration Control sensors have NTC thermistors. The reference resistance is 30,000 ohms at 77°F (25°C). It carries NTC thermistors with a range of –40°to 199° F. In case there is a failure, these sensors should be used in replacement of the sensors shipped with the control. In order to diagnose faults in the probe, the control has LED functions as a diagnostic tool. When power is supplied to the control, the LED will turn on and will remain on as long as this condition is satisfied. When there is a fault in the probe, the LED will blink intermittently. When this occurs, the probe assembly needs to be replaced. If power is supplied to the control and the LED remains off, there is a failure in the main relay control and it needs to be replaced.

In case of a probe failure, the control will go into a safety mode of operation. While in safety mode the control ignores probe inputs and cycles the compressor on for 5 minutes and off for 3 hours. The LED will be blinking and signaling that there is something wrong with the probe. To replace the sensor probes, disconnect power to the control, replace the probes and restart the unit. Since the wire is fixed to the cabinet, a technician may cut the sensor wire inside the cabinet and splice it with a new sensor.

SENSOR PROBE TEMPERATURE AND RESISTANCE

 

Temperature

 

Resistance

°F

 

°C

 

Ohms

-29.2

 

-34

 

683,100

-20.2

 

-29

 

499,200

-9.4

 

-23

 

347,100

-0.4

 

-18

 

259,500

10.4

 

-12

 

185,200

19.4

 

-7

 

141,200

30.2

 

-1

 

103,100

32.0

 

0

 

97,950

39.2

 

4

 

80,040

50.0

 

10

 

59,700

60.8

 

16

 

45,000

69.8

 

21

 

35,820

80.6

 

27

 

27,500

89.6

 

32

 

22,210

 

 

 

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Master-Bilt Products Installation & Operations ManualPage Table of Contents Store Conditions IntroductionGround Required For Safe Operation Installation Instructions PRE-INSTALLATION InstructionsInspection for Shipping Damage MechanicalElectrical ERC 2 Electronic Refrigeration Control Low Temperature Freezers TAF ModelsPress and hold set for 5 seconds. The display will show CLoC Elec Con ALHi Error Codes Display Control StatusTemperature Resistance Ohms Sensor Probe Temperature and ResistanceFinal Check List Sensor ProbeService Instructions Trouble Shooting Guide MASTER-BILT Part Numbers Owner Responsibility Sale and Disposal

TAF-74 ERC2, TAF-27 ERC2, TAF-48 ERC2 specifications

The Master Bilt TAF series, which includes models TAF-48 ERC2, TAF-27 ERC2, and TAF-74 ERC2, represents a substantial advancement in refrigeration technology, specifically designed for food service and commercial kitchens. Each model in this series has been engineered to meet diverse cooling requirements while ensuring energy efficiency and reliability.

The TAF-48 ERC2 is a robust unit with a 48-inch width, making it an ideal choice for establishments that require ample refrigeration space without sacrificing energy efficiency. This model features a digital temperature control system, allowing for precise monitoring and adjustments of internal temperatures. Its front-breathing design enables it to be used in confined spaces, optimizing workflow in busy kitchens. The TAF-48 ERC2 is equipped with LED interior lighting, enhancing visibility for quick access to stored items, and comes with adjustable shelves to accommodate various sizes of products.

In contrast, the TAF-27 ERC2 offers a more compact solution for locations with limited space. With a 27-inch width, it is perfect for smaller kitchens or front-of-house applications. Despite its size, the TAF-27 ERC2 is built with the same quality components as the larger models. This unit also includes a digital control system for easy temperature management and energy-efficiency features that contribute to lower operational costs.

The TAF-74 ERC2 stands out with its impressive 74-inch width, tailored for high-volume operations. It features a powerful compressor and advanced refrigeration technology that ensures fast and consistent cooling, critical for busy environments. This model is particularly suited for establishments like buffets or catering services, where large quantities of food need to be quickly accessed and maintained at safe temperatures.

All models in the Master Bilt TAF series incorporate environmentally friendly refrigerants, reflecting a commitment to sustainability. They are designed for easy cleaning with rounded corners and removable shelves, making maintenance straightforward. Each model boasts a durable construction, ensuring longevity even in the most demanding kitchen settings.

In summary, Master Bilt's TAF-48 ERC2, TAF-27 ERC2, and TAF-74 ERC2 deliver exceptional reliability, energy efficiency, and user-friendly features, making them ideal choices for a variety of commercial refrigeration needs. Each unit is crafted to provide optimal performance while prioritizing ease of use and sustainable practices.
Top Page Image Contents