U-Line 2075RF manual Assembling the Door, Installing the Door

Page 11

2075R Refrigerator and 2075RF Refrigerator/Freezer

 

Typical

Door Panel

Wood Panel

 

Top

Pivot Plate

#10 x 5/8"

Round Head Screw

Seven Required

Plastic Spacer

Seven Required

Figure 22

5.Remove the existing bottom pivot plate and replace with the Full Overlay pivot plate (see Figure 23).

Existing

 

Door

Wood Panel Bottom Pivot Plate

 

(5/8" Longer Than

Existing Bottom Pivot Plate

Existing Bottom Pivot Plate,

(Remove and Discard)

Flush Side Facing Out)

 

#8-32 x 3/8" SEMS Hex Screw

 

Two Places

Figure 23

IMPORTANT

Door panel and overlay panel must be aligned properly or the door will not operate correctly.

Assembling the Door

1.Install the assembled panel by sliding the original door panel back into the doorframe.

2.Replace the two-piece Modified Handle assembly and secure with the two screws removed in Step 6 under Removing Existing Door.

3.Starting at the corners and working toward the center, push the door gasket back into place.

Installing the Door

1.Remove the existing hinges from the unit, saving the door closure assembly.

2.Install the new Replacement Top Hinge onto the unit (see Figure 24).

Pivot Post

Wood Panel Top Hinge Plate

(5/8" Longer than Existing Top Hinge Plate)

#8-32 x 1/2"

Flat Head Screw

Three Places

Top Pivot Plate

Door Panel

Figure 24

3.Install the pivot post into the new Replacement Bottom Hinge (using the 7/64" hex key or Phillips screwdriver) and install the hinge onto the unit.

4.Replace the door closure assembly onto the bottom pivot post (see Figure 25). Be sure that bosses on closers align with holes in hinge and hinge plate.

 

Existing

 

Door

Door Closure Top

Boss

Door Closure Bottom

 

 

#8-32 x 1/2" Flat Head Screw

Boss

Three Places

 

Wood Panel Bottom Hinge Plate

Pivot Post

(5/8" Longer than Existing Bottom Hinge Plate)

Figure 25

IMPORTANT

Pivot posts must be cleaned. Closers must also be clean and greased to ensure proper operation.

5.Place the modified door onto the pivot post.

6.Position door and install the pivot post into the top hinge (using the 7/64" hex key or Phillips screwdriver).

7.Adjust door as needed for proper closure.

8.Check to see that light switch actuator bracket is contacting the light switch properly.

9.Reinstall the door shelves by lining up the bosses and first pushing straight in, then down at a 45° angle (see Figure 34 on Page 14). Go on to 5 Adjust Door.

02/2005

11

www.U-LineService.com

Image 11
Contents 2075R Refrigerator 2075RF Refrigerator/Freezer Follow Safety Precautions ContentsInspection General PrecautionsInspect and Plan Tools/Materials RequiredBlack and White Models Exterior CleaningCut-Out Dimensions Prepare SiteDoor Swing/Clearances Information Reversing the Door Product DimensionsEnvironmental Requirements Power SupplyOther Site Requirements Custom 1/4 Door Panel Insert Side-By-Side Installation InstructionsPrepare and Install Door Panel Door Panel InstallationFull Overlay Door Panel Removing Existing Door Installation InstructionsAttaching the Full Overlay Panel Assembling the Door Installing the DoorChecking Door Alignment Adjusting Door AlignmentAdjust Door To 6 Prepare PowerLeveling Information Electrical SpecificationsInstallation Tip Prepare Power SupplyRelocating the Shelves Installation of the 2075R/2075RFInstallation Troubleshooting Install the UnitStart-Up for the First Time Start-Up TroubleshootingInitial Start-Up Who to Call Service Information

2075RF, 2075R specifications

The U-Line 2075R and 2075RF are exceptional refrigeration units designed to meet the needs of modern kitchens and entertaining spaces. Known for their sleek design and advanced features, these products stand out in the market for their efficiency and versatility.

One of the primary features of the U-Line 2075R is its impressive capacity. With a total storage space of up to 5.7 cubic feet, it can accommodate a wide range of beverages, including bottles, cans, and more. The model is designed with adjustable shelving, allowing users to customize the interior layout according to their storage needs. This flexibility makes it ideal for home use as well as for commercial settings.

The U-Line 2075RF model enhances the standard features of the 2075R by incorporating a more sophisticated refrigeration technology. It includes a dual-zone cooling system, which enables precise temperature control for both wine and general beverage storage. Each zone can be adjusted independently, making it the perfect choice for connoisseurs who want to preserve their wine at optimal temperatures while also keeping other beverages chilled.

Both models boast a stunning glass door that offers a clear view of the contents without opening the unit, which helps maintain internal temperatures and save energy. The LED lighting inside is strategically placed to provide excellent visibility while being energy-efficient. Users can also choose from multiple interior configurations thanks to the removable shelves, allowing for easy organization based on personal preferences.

U-Line prioritizes energy efficiency, and both the 2075R and 2075RF are Energy Star certified. This means they are designed to consume less energy compared to conventional models, helping users save on utility costs while also being more environmentally friendly. The quiet operation of these units is another significant advantage, as it minimizes noise disruption in any setting.

Lastly, the exterior of both models features a stainless-steel finish, adding a touch of elegance that blends seamlessly with various kitchen styles. The front ventilation allows for built-in or freestanding installation, increasing their adaptability in different spaces.

In summary, the U-Line 2075R and 2075RF are top-of-the-line refrigeration solutions, engineered for optimal performance, energy efficiency, and stylish design, making them perfect for both residential and commercial applications.