U-Line 2075RF manual Side-By-Side Installation Instructions, Custom 1/4 Door Panel Insert

Page 7

2075R Refrigerator and 2075RF Refrigerator/Freezer

 

Side-By-Side Installation

Instructions

For a complete refreshment center, install your 2075R or 2075RF Model beside a U-Line Ice Maker, Combo or Wine Captain Model (see Figure 11 for typical cut-out). Note that each Side-By-Side Installation will be different.

Cut-out width for a side-by-side installation is the total of the widths listed under Cut-Out Dimensions in each unit’s Installation Guide.

For example:

Placing a 2075R or 2075RF next to a 2015 series unit would require a cut-out width of:

24-3/16" + 15-3/16" = 39-3/8"

Placing a 2075R or 2075RF next to a 2075 series unit would require a cut-out width of:

24-3/16" + 24-3/16" = 48-3/8"

No trim kit is required. However, 1/4-inch space needs to be maintained between the units to ensure unobstructed door swing.

Units must operate from separate, properly grounded electrical receptacles placed according to each unit’s Electrical Specifications.

Typical Side-By-Side Cut-Out

 

34-1/4"

23-1/4"

to

 

35-1/8"

7"

 

1/4" Space

 

Between

1-1/2"

Appliances

 

Figure 11

 

4 Prepare and Install Door Panel

(Black and White Units Only)

Two types of custom door panels can be installed on your Black or White unit to harmonize with or accent the surrounding décor: a Custom 1/4" Insert or a Full Overlay. If no custom door panel is used, go on to 5 Adjust Door.

Custom 1/4'' Door Panel Insert

Door Panel Preparation

A custom door panel can be inserted into the doorframe. Custom door panels can be flat or raised, as long as the maximum panel thickness where inserted into the door reveal (channel) is 1/4"-thick. For raised panels, the depth of the reveal is 1/4" on all four sides.

IMPORTANT

Raised panels will reduce the door’s 90° swing/zero clearance if the unit is installed next to a wall or similar type of structure (see Page 5).

Cut the panel insert to the following dimensions.

Custom 1/4" Dimensions:

Width: 23-1/32"

Height: 28-5/32"

The door panel must not weigh more than 20 lbs.

Door Panel Installation

Install the insert as follows:

1.Remove the door shelves by first pulling shelves

up at a 45° angle then straight out (see Figure 34 on Page 14).

CAUTION

Use care when handling the insert. Insert edges may be sharp.

2.Remove top hinge screw pin (7/64" Allen wrench or Phillips screwdriver, depending on your unit’s construction, see Figure 12). Remove door by tilting forward and lifting off bottom hinge pin.

02/2005

7

www.U-LineService.com

Image 7
Contents 2075R Refrigerator 2075RF Refrigerator/Freezer Follow Safety Precautions ContentsInspection General PrecautionsInspect and Plan Tools/Materials RequiredBlack and White Models Exterior CleaningCut-Out Dimensions Prepare SiteDoor Swing/Clearances Information Reversing the Door Product DimensionsOther Site Requirements Power SupplyEnvironmental Requirements Custom 1/4 Door Panel Insert Side-By-Side Installation InstructionsPrepare and Install Door Panel Door Panel InstallationFull Overlay Door Panel Removing Existing Door Installation InstructionsAttaching the Full Overlay Panel Assembling the Door Installing the DoorChecking Door Alignment Adjusting Door AlignmentAdjust Door To 6 Prepare PowerLeveling Information Electrical SpecificationsInstallation Tip Prepare Power SupplyRelocating the Shelves Installation of the 2075R/2075RFInstallation Troubleshooting Install the UnitInitial Start-Up Start-Up TroubleshootingStart-Up for the First Time Who to Call Service Information

2075RF, 2075R specifications

The U-Line 2075R and 2075RF are exceptional refrigeration units designed to meet the needs of modern kitchens and entertaining spaces. Known for their sleek design and advanced features, these products stand out in the market for their efficiency and versatility.

One of the primary features of the U-Line 2075R is its impressive capacity. With a total storage space of up to 5.7 cubic feet, it can accommodate a wide range of beverages, including bottles, cans, and more. The model is designed with adjustable shelving, allowing users to customize the interior layout according to their storage needs. This flexibility makes it ideal for home use as well as for commercial settings.

The U-Line 2075RF model enhances the standard features of the 2075R by incorporating a more sophisticated refrigeration technology. It includes a dual-zone cooling system, which enables precise temperature control for both wine and general beverage storage. Each zone can be adjusted independently, making it the perfect choice for connoisseurs who want to preserve their wine at optimal temperatures while also keeping other beverages chilled.

Both models boast a stunning glass door that offers a clear view of the contents without opening the unit, which helps maintain internal temperatures and save energy. The LED lighting inside is strategically placed to provide excellent visibility while being energy-efficient. Users can also choose from multiple interior configurations thanks to the removable shelves, allowing for easy organization based on personal preferences.

U-Line prioritizes energy efficiency, and both the 2075R and 2075RF are Energy Star certified. This means they are designed to consume less energy compared to conventional models, helping users save on utility costs while also being more environmentally friendly. The quiet operation of these units is another significant advantage, as it minimizes noise disruption in any setting.

Lastly, the exterior of both models features a stainless-steel finish, adding a touch of elegance that blends seamlessly with various kitchen styles. The front ventilation allows for built-in or freestanding installation, increasing their adaptability in different spaces.

In summary, the U-Line 2075R and 2075RF are top-of-the-line refrigeration solutions, engineered for optimal performance, energy efficiency, and stylish design, making them perfect for both residential and commercial applications.