Sub-Zero ICBBI-36F BUILT-IN Insta LL Atio N Instru CTI on S, Elect Rica L Requ Irem Ents

Page 7

BUILT-IN INSTA LL ATIO N INSTRU CTI ON S

ELECT RICA L REQU IREM ENTS

A 220-240 V AC, 50/60 Hz, 10 amp circuit breaker and electrical supply are required. A separate circuit, servicing only this appliance, is required.

All Sub-Zero Built-In models are equipped with a power supply cord with a 3-prong grounding plug, which must be plugged into a mating

3-prong grounding-type wall receptacle. Follow local codes and ordinances when installing the receptacle. For location of the electrical supply, refer to the Installation Specifications illustration for your specific model on pages 4–6.

IMPORTANT NOTE: A ground fault circuit interrupter (GFCI) is not recommended and may cause interruption of operation.

WARNING

Do not use an extension cord or two-prong adapter. Electrical ground is required on this appliance. Do not remove the power supply cord ground prong.

CAUTION

The outlet must be checked by a qualified electrician to be sure that it is wired with the correct polarity. Verify that the outlet provides 220-240 V AC and is properly grounded.

WARNING

Always shut power off at the circuit breaker before performing any installation, service or maintenance.

IMPORTANT NOTE: The Built-In line is equipped with an appliance inlet type device. This allows easy replacement of the power cord. The appliance inlet is located on top of the unit on the compressor shroud. When replacing the power cord make sure that the replacement cord is rated HO5VV-F3G1.0 or equivalent to ensure safe operation of the appliance.

PLUMBIN G REQUIRE MENTS

IMPORTANT NOTE: A reverse osmosis system can be used, provided there is constant water pressure of 2.1 bar to 6.9 bar supplied to the unit at all times.

Rough in the cold water supply line using 6 mm OD copper line. The water line should be routed up through the floor within 13 mm from the back wall and no higher than 76 mm off the floor. If you have to come through the wall, make sure the water line is no more than 76 mm from the floor.

Regardless of the routing, allow .9 m of excess copper tubing to remain outside the wall or floor for easy connection to the unit. Locate the water supply line within the shaded area indicated in the Installation Specifications illustration for your specific model on pages 4–6.

Use an easily accessible shut-off valve between the water supply and the unit. Do not use self-piercing valves. A saddle valve kit (4200880) is available from your Sub-Zero dealer.

It is not recommended that the ice maker be connected to a softened water supply. Water softener chemicals, such as salt from a malfunc- tioning softener, can damage the ice maker and lead to poor ice quality. If a softened water supply cannot be avoided, be sure that the water softener is well maintained and operating properly.

IMPORTANT NOTE: All installations must meet local plumbing code requirements.

IMPORTANT NOTE: This appliance should be connected to a potable water supply.

UNPACK TH E UNIT

Uncrate the unit and inspect for any damages. Remove the wood base and discard the shipping bolts and brackets that hold the wood base to the bottom of the unit. Remove and discard all packing materials.

IMPORTANT NOTE: Do not discard the kick- plate, anti-tip bracket and hardware. These items will be needed for installation.

Retract the front leveling legs all the way up to allow the unit to be moved into position more easily. You will extend the leveling legs when the unit is in its final position to reduce the possibil- ity of the unit tipping forward.

IMPORTANT NOTE: The rear levelers must be in their lowest position in order to push the unit back into the rough opening. Therefore, leveling cannot be completed until the unit is in position.

Remove the drain pan from the base of the unit to avoid damage to the drain pan, and allow for proper placement of the appliance dolly.

WARNING

Be sure to secure the door(s) closed before moving the unit.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents
Built -IN RE Frig Erati on Italia no English Españ OL Franç AIS Site PR EPA RAT ION SU B-ZE RO Buil T-IN REF Riger Ation BUILT-IN Insta LL Atio N Tools and Mate RI ALS RE QUI REDDo or Cleara NCE Over ALL DimensionsBUILT-IN Insta LL Atio N Specifi Cati ONS STA LL Atio N Specif ICA Tion SModel ICBBI-36UG 902 mm 965 mm Model ICBBI-30UModel ICBBI-36U Model ICBBI-36UG Model ICBBI-30U 749 mm 813 mmSide-by-Side Models Flush Inset Application Side-by-Side ModelsModel ICBBI-36S 902 mm 965 mm Unpack TH E Unit BUILT-IN Insta LL Atio N Instru CTI on SElect Rica L Requ Irem Ents Plumbin G Require MentsConcrete Floo R Appli CAT ION S ANT I-T IP BRA Cket Installa TionGR Ille Remo VAL WOO D FL OOR AP PL ICA TIO NSPosi Tion the Unit Anti -TIP BR AC KET INS Talla TionAN TI -TIP Hardw are Included INS Tall Conc Rete WE DG E ANC HorsINS Tall TH E KI Ckpla TE Level the UN IT Overla Y PAN ELSGrille Trim GL Asswel L- DI Spenser MOD ELS GR Ille Panel AS Sembly OVE Rlay Pane L in Stallat IONOVE Rlay Pane L Specifica Tion S Spacer Panel Flush Inset Panel Installa TI onFlush Inset Panels Grill E PAN EL Assem BLY Mm Backer PanelModel ICBBI-36R Models ICBBI-30U and ICBBI-30UG Flush Inset Panel SP Ecifi Cati ONSModel ICBBI-36F Models ICBBI-36U and ICBBI-36UG Dual Instal Lation S SI DE Panel in STA LlationSI DE Panel in STA Llation WO OD SID E Pane LSCO Mplet ING TH E Installa TI on SER Vice in Form Ation INS Tallatio N ChecklistINS Tall AT ION CHE Ckli ST SER Vice in Form AtionPrepar Ación DE L Sitio REF Riger Ación Empo Trab LE SU B-ZER OINS Tala Ción EMP Otrable Herram IE Ntas Y Mater Iale S Necesar IO SEspeci Ficaci on ES DE LA Instal ACI ÓN Struccio NES DE Instalació N Para Productos Empotrab LE SES Pacio Para Apertura DE Puerta Modelo ICBBI-30U Modelo ICBBI-30UG ME DI DAS to TalesModelo ICBBI-30U 749 mm Modelo ICBBI-30U 794 mmModelo ICBBI-42S Modelo ICBBI-42SD Modelo ICBBI-36S 914 mm 138 mm 610 mm Modelo ICBBI-42SModelo ICBBI-36S 902 mm Modelo ICBBI-36SREQ UI SIT OS DE FON TAN ER ÍA REQ Uisito S ELÉ CT RicosDese Mbalaje DE LA Unid AD APL Icac Iones EN Suel O DE Hormi GÓ N Apli Caci on ES EN Suelo DE MAD ER aInstalació N DE Anclaj ES DE Expan Sión Para HO RM IGÓ N PI EZ AS Antivue LCO IncluidasInstala Ción DEL Panel DE REV Estim Iento Struccio NES DE Instalació N Para PRO Ducto S EM Potrab LESNI Velació N DE LA Unidad Stala CIÓ N DEL ZócaloStala CIÓ N DEL Panel DE Revestimi Ento Espe CIF Icacione S DEL PAN EL DE Reve STI MI Ento Panel trasero Stala CIÓ N DE Panel Empotr AblePanele S EMP Otra Bles Montaje DEL Panel DE Rejil LAPaneles Empotr Ables DE REJ IL LA Pane LES DE PU Erta EM PO TR AblesPaneles DE REJ IL LA EM Potr ABL ES DOB LES Instala CIO NES Dobles Stala CIÓ N DEL Panel Latera LStala CIÓ N DEL Panel Latera L PA Neles Late RAL ES DE MAD ERAFIN Aliza Ción DE LA Instala CIÓ N Inform Ació N DE MAN TEN Imient O LIS TA DE CO MP ROB Ación DE LA Instala CIÓ NLIS TA DE CO MPR Obaci ÓN DE LA Instalació N Inform Ació N SO BRE EL Mant Enim IentoPrépar Ation DE L’E MPL Acem EN T AP PAR Eils DE RÉ Frigé Ration EN Castra BL ES SU B-ZEROStallatio N Pour LES Appar EI LS Encastr Able S Outi LS ET Matér Iaux RE QUI SSpéc Ifica Tion S D’ INS Tall Ation DI MEN SIO NS HOR S TOU TDÉ Gagem ENT DE LA Porte Modèle ICBBI-36U Modèle ICBBI-30UModèle ICBBI-30UG avec porte vitrée Modèle ICBBI-30UGModèle ICBBI-48S Modèle ICBBI-48SD 067 mm 138 mm 610 mm Modèle ICBBI-48S 219 mm219 mm 138 mm 610 mm Modèle ICBBI-36SConf Igura TIO N DE LA PL OM BER IE Conf Igur Ation ÉL Ectriq UEDéball AG E DE L’A Ppareil SUR UN SOL EN BÉT on RET RA IT DE LA GRI LLEStal LAT ION DU SUP PO RT ANTI- Basculem ENT SUR UN PL Anche R EN BoisMise EN PL ACE DE L’APP Areil Installatio N DES Cale S D’ANCR AGE Pour SOL EN BÉ to NStallatio N DU Suppor T ANTI- Basculem ENT MA Tériel ANT Ibasculem ENT InclusStallatio N DE LA Plinthe Mise À Nivea U DE L’APPAREI Panneaux D’HA Billa GEPanneau d’habillage Panneau intercalaire Mandes Stallatio N Avec Panne AU D’ HA Billa GETémoin de verrouillage Touche pourSP Écificatio NS Concer Nant LES Pannea UX HA Bill Ables Stallatio N Avec Panne AU D’ Affl Eureme NT Panneaux D’AFFLEU REM EN T DE Grill E do UB LES SP Écificatio NS Concer Nant LES Pannea UX D’ AF FleurementPanneaux DE POR TE D’AFFL EUR Ement Panneaux DE Gril LE D’A FFL EUR EM EN TPA Nneaux DE CÔ TÉ EN Bois Install Ation S Conjoin TESPO SE DES Panne AUX DE CÔ TÉ PO SE DES Panne AUX DE CÔ TÉPO UR TE Rmine R L’INSTALLATIO N SER Vice Aprè S-V Ente LIS TE DE CO Ntrôl EDE L’INSTA LLA TI onListe DE CO NTR ÔLE DE L’INSTA LLA Tion SER Vice Aprè S-V EntePrepar Azio NE DE L SIT O Frigo RIF ERI DA in Casso SUB -Z ER OINS Talla Zione DA Incasso Attrez ZI E Mater IAL E Richie STISP Azio Porta SP Ecifiche PE R L’INSTALLAZI ONE DA IncassoDIM Ensio NI GE NER ALI Specifiche PE R L’I NSTAL- LazioneModello ICBBI-30U 749 mm 813 mm Modello ICBBI-30UModello ICBBI-30U Modello ICBBI-30UG Modello ICBBI-36U Modello ICBBI-36UGModello ICBBI-48S Modello ICBBI-48SD Modello ICBBI-36SModello ICBBI-42S Modello ICBBI-42SD Modello ICBBI-36S 902 mm 965 mmDisi Mballa Ggio DEL L’U Nità PE R L’INSTALLAZI ONE DA IncassoREQ Uisiti Elett Rici Collegam Ento ID RicoAppli Cazio NE PE R PA VIM Enti in Legno Is TR Uzioni PER L’INST Allaz Ione DA Inca SSORI MOZ IO NE DE LL a Griglia Instal LA ZIO NE Della BA RRA Antir Ibal TAM EntoInstallaz IO NE DEI Tasselli PER Cemento Is TR Uzion I PER L Installa Zion E DA Inca SSOMI Nuteria ANT IRI Baltamen to in Dotazione Pannel LO a SO VR AP Posizio NE Installa Zione DE I Pannelli a SO Vrap PO Sizio NELIV Ellam Ento DE LL’UNIT À Stalla Zion E Dello Zocc OLOMO Delli CON ERO Gato RE E Vano Bicchier E Stalla Zion E DEI Pann Elli a Sovr AP Posi ZIO NEMonta GG IO DEL PAN NE LL O CO N Grigli a SP Ecifiche Panne LLI a Sovr APP Osizi ONE Pannelli con inserti a filo Stalla Zion E DEI Pann Elli CON Inserto a FI LOPannelli con Inserti a filoPannelli CON Inser to a FIL O CON Gliglia Doppia SP Ecifiche DEL Pannello CON Inserti a FI LOPannelli PE R Porta CON Inse RTO a Filo Pannelli GR IGL IA CON INS ER to a FiloPA Nnelli Late Rali in Legno Install AZ IO NI DOP PIEStalla Zion E DEI Pann Elli Latera LI Stalla Zion E DEI Pann Elli Latera LIREG Olaz IO NE DELL’ALTEZ ZA PO RTE COM Plet Amento DELL’INSTALLA ZI ONERegol Azio NE Inte RNO/ESTERNO REG Olaz IO NE CO N SPO Stame NTO Latera LECheck LI ST DI Installaz IO NE CHE Cklist DI Installazio NEInform Azio NI SU L SER Vizio DI Assi Stenz a Vorb ER EIT UNG DES INS TA LL AT ION S- Ortes SU B-ZE RO Einb AUK Ühltechn IKEIN BA Uinst AL Lati on Erfo RD Erli CHE WE RK ZE UGE UND Material IE NTürf Reirau M Technische Daten ZUR Einb AUI Nsta LLA TIO NGE Samt Abmessu NG EN Tech NIS CHE DA TE N ZUR Stalla TI onStalla Tion Technische Date N ZUR Einb AU Inst Allat IONGesam TAB Messung EN Technis CH E Date N ZURTEC Hnis CHE DA TE N ZUR Technische Date N ZUR EI NB Auinstallati onGesam Tabme SSU NGE N TÜ RF REI RAU MElekt RO VOR Auss Etzunge N AN Weisungen ZUR Einbauinsta Llat IONAuspa CKE N DES GER ÄTS Beton Bode NA Nwen DU Ngen AU Sbaue N DES GIT TersStal LAT ION DER KIP Pschut Zhal TER UNG Holzb ODE Naus FÜH RU NgenPosi Tionie RE N DES GE RÄT S Beto Nank ER KE ILE Installie RENStallatio N DER Kippsch Utzhal TER UNG Befestigung Steile FÜR KI Ppschutz InbegriffenStallatio N DER Sockellei STE NI Vellier EN DE S Gerä TSVerkle Idungsp Latten GL Asbe TT SPE Nder Modelle Stallatio N DER Verkleidung Spla TTEGI Tterp Latt EN BAU GR UPP E Verkl EID UNG SG IT Terp Latt EN Technische Date N ZU VER KLE Idungsp Latte NVerkle Idungstür Platte N VER KLE ID UNG ST ÜR PLA TtenBündige BÜ NDIGE/VO LL Integrie RTE Plat Teni Nsta LLA TI onBÜ NDIGE/VO LL Integrie RTE Plat TEN Gitterp Latten Baugru PPETechnische Date N ZU Bündi GEN/VOLL Integ RI ERT EN Platten DOP Pelinst Allatio NEN Stallatio N DER Seitenpla TTEStallatio N DER Seitenpla TTE SE Itenpl Atten AUS HOL ZAbschluss DER Installation Installatio Nsche CK Liste Stallatio NschecklisteSER Vicein for Mation EN SUB -Z ERO , INC
Related manuals
Manual 69 pages 3.33 Kb
Top Page Image Contents