Sub-Zero ICBBI-36RG, ICBBI-36F GR Ille Remo VAL, ANT I-T IP BRA Cket Installa Tion, 610 m m

Page 8

BUILT-IN INSTA LL ATIO N INSTRU CTI ON S

GR ILLE REMO VAL

In order to prevent damage to the grille and to access the power cord, the top grille assembly should be removed prior to moving the unit.

To remove the grille assembly, pull out on the bottom edge of the grille and tilt it upward. Loosen the back two grille mounting screws and remove the front two grille mounting screws. With the grille held firmly, pull forward to remove. Refer to the illustrations below.

To reinstall the grille, insert the grille into position and be sure that the grille catch tabs are engaged. Reinstall the front two grille screws, then retighten the back two grille screws. Check for proper fit.

ANT I-T IP BRA CKET INSTALLA TION

WARNING

To prevent the unit from tipping forward and provide a stable installation, the unit must be secured in place with the anti-tip brackets shipped with the unit.

IMPORTANT NOTE: Placement of the anti-tip brackets is critical to a stable installation. Failure to properly position the anti-tip brackets will prevent them from engaging the unit.

The two anti-tip brackets must be installed exactly 610 mm from the front of the rough opening to the back of the brackets and a minimum of 102 mm from the sides of the rough opening. This depth will increase to 665 mm for a flush inset installation based on 19 mm deep decorative panels. Proper placement will ensure that the anti-tip brackets engage the anti-tip bar at the back of the unit.

IMPORTANT NOTE: Both anti-tip brackets MUST be used.

WOO D FL OOR AP PL ICA TIO NS

After properly locating the anti-tip brackets in the rough opening, drill pilot holes 5 mm diameter maximum in the wall studs and/or wall plate. Use the #12 x 64 mm PH pan HD zinc screws and #12 flat washers to secure the brackets in place. Be sure that the screws penetrate through the flooring material and into wall studs or wall plate a minimum of 19 mm. Refer to the illustration below.

CONCRETE FLOO R APPLI CAT ION S

After properly locating the anti-tip brackets in the rough opening, drill pilot holes 5 mm diameter maximum in the wall studs and/or wall plate. Then drill 10 mm diameter holes into the concrete a minimum of 13 mm deep. Use the #12 x 64 mm PH pan HD zinc screws and #12 flat washers to secure the brackets to the wall and use the 10 mm–16 x 95 mm wedge anchors to secure the brackets to the floor. Be sure that the screws penetrate the wall studs or wall plate a minimum of 19 mm. Refer to the illustration below.

IMPORTANT NOTE: For either wood or concrete floor applications, if the #12 x 64 mm screws do not hit a wall stud or the wall plate in any of the back holes of the brackets, use the provided #8–18 x 32 mm PH truss HD screws and #12 flat washers with the nylon zip-it wall anchors.

IMPORTANT NOTE: In some installations the subflooring or finished floor may necessitate angling the screws used to fasten the anti-tip brackets to the back wall.

Back Grille

Screw

Front Grille Screw

Grille removal

Grille mounting screws

610 mm

102 mm

MIN

Wood floors

610 mm

102 mm

MIN

13 mm

MIN

Concrete floors

AC CESSO RIE S

Optional acces- sories are available through your Sub-Zero dealer. To obtain local dealer information, visit our website, subzero.com.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Built -IN RE Frig Erati on English Españ OL Franç AIS Italia noSU B-ZE RO Buil T-IN REF Riger Ation BUILT-IN Insta LL Atio NTools and Mate RI ALS RE QUI RED Site PR EPA RAT IONOver ALL Dimensions BUILT-IN Insta LL Atio N Specifi Cati ONSSTA LL Atio N Specif ICA Tion S Do or Cleara NCEModel ICBBI-30U Model ICBBI-36U Model ICBBI-36UGModel ICBBI-30U 749 mm 813 mm Model ICBBI-36UG 902 mm 965 mmModel ICBBI-36S 902 mm 965 mm Side-by-Side ModelsSide-by-Side Models Flush Inset Application BUILT-IN Insta LL Atio N Instru CTI on S Elect Rica L Requ Irem EntsPlumbin G Require Ments Unpack TH E UnitANT I-T IP BRA Cket Installa Tion GR Ille Remo VALWOO D FL OOR AP PL ICA TIO NS Concrete Floo R Appli CAT ION SAnti -TIP BR AC KET INS Talla Tion AN TI -TIP Hardw are IncludedINS Tall Conc Rete WE DG E ANC Hors Posi Tion the UnitGrille Trim Level the UN IT Overla Y PAN ELSINS Tall TH E KI Ckpla TE OVE Rlay Pane L in Stallat ION GL Asswel L- DI Spenser MOD ELS GR Ille Panel AS SemblyOVE Rlay Pane L Specifica Tion S Flush Inset Panel Installa TI on Flush Inset Panels Grill E PAN EL Assem BLYMm Backer Panel Spacer PanelModel ICBBI-36F Models ICBBI-36U and ICBBI-36UG Flush Inset Panel SP Ecifi Cati ONSModel ICBBI-36R Models ICBBI-30U and ICBBI-30UG SI DE Panel in STA Llation SI DE Panel in STA LlationWO OD SID E Pane LS Dual Instal Lation SCO Mplet ING TH E Installa TI on INS Tallatio N Checklist INS Tall AT ION CHE Ckli STSER Vice in Form Ation SER Vice in Form AtionREF Riger Ación Empo Trab LE SU B-ZER O INS Tala Ción EMP OtrableHerram IE Ntas Y Mater Iale S Necesar IO S Prepar Ación DE L SitioES Pacio Para Apertura DE Puerta Struccio NES DE Instalació N Para Productos Empotrab LE SEspeci Ficaci on ES DE LA Instal ACI ÓN ME DI DAS to Tales Modelo ICBBI-30U 749 mmModelo ICBBI-30U 794 mm Modelo ICBBI-30U Modelo ICBBI-30UGModelo ICBBI-36S 914 mm 138 mm 610 mm Modelo ICBBI-42S Modelo ICBBI-36S 902 mmModelo ICBBI-36S Modelo ICBBI-42S Modelo ICBBI-42SDDese Mbalaje DE LA Unid AD REQ Uisito S ELÉ CT RicosREQ UI SIT OS DE FON TAN ER ÍA Apli Caci on ES EN Suelo DE MAD ER a APL Icac Iones EN Suel O DE Hormi GÓ NPI EZ AS Antivue LCO Incluidas Instalació N DE Anclaj ES DE Expan Sión Para HO RM IGÓ NStruccio NES DE Instalació N Para PRO Ducto S EM Potrab LES NI Velació N DE LA UnidadStala CIÓ N DEL Zócalo Instala Ción DEL Panel DE REV Estim IentoStala CIÓ N DEL Panel DE Revestimi Ento Espe CIF Icacione S DEL PAN EL DE Reve STI MI Ento Stala CIÓ N DE Panel Empotr Able Panele S EMP Otra BlesMontaje DEL Panel DE Rejil LA Panel traseroPaneles DE REJ IL LA EM Potr ABL ES DOB LES Pane LES DE PU Erta EM PO TR AblesPaneles Empotr Ables DE REJ IL LA Stala CIÓ N DEL Panel Latera L Stala CIÓ N DEL Panel Latera LPA Neles Late RAL ES DE MAD ERA Instala CIO NES DoblesFIN Aliza Ción DE LA Instala CIÓ N LIS TA DE CO MP ROB Ación DE LA Instala CIÓ N LIS TA DE CO MPR Obaci ÓN DE LA Instalació NInform Ació N SO BRE EL Mant Enim Iento Inform Ació N DE MAN TEN Imient OAP PAR Eils DE RÉ Frigé Ration EN Castra BL ES SU B-ZERO Stallatio N Pour LES Appar EI LS Encastr Able SOuti LS ET Matér Iaux RE QUI S Prépar Ation DE L’E MPL Acem EN TDÉ Gagem ENT DE LA Porte DI MEN SIO NS HOR S TOU TSpéc Ifica Tion S D’ INS Tall Ation Modèle ICBBI-30U Modèle ICBBI-30UG avec porte vitréeModèle ICBBI-30UG Modèle ICBBI-36U067 mm 138 mm 610 mm Modèle ICBBI-48S 219 mm 219 mm 138 mm 610 mmModèle ICBBI-36S Modèle ICBBI-48S Modèle ICBBI-48SDDéball AG E DE L’A Ppareil Conf Igur Ation ÉL Ectriq UEConf Igura TIO N DE LA PL OM BER IE RET RA IT DE LA GRI LLE Stal LAT ION DU SUP PO RT ANTI- Basculem ENTSUR UN PL Anche R EN Bois SUR UN SOL EN BÉT onInstallatio N DES Cale S D’ANCR AGE Pour SOL EN BÉ to N Stallatio N DU Suppor T ANTI- Basculem ENTMA Tériel ANT Ibasculem ENT Inclus Mise EN PL ACE DE L’APP AreilPanneau d’habillage Panneau intercalaire Mise À Nivea U DE L’APPAREI Panneaux D’HA Billa GEStallatio N DE LA Plinthe Stallatio N Avec Panne AU D’ HA Billa GE Témoin de verrouillageTouche pour MandesSP Écificatio NS Concer Nant LES Pannea UX HA Bill Ables Stallatio N Avec Panne AU D’ Affl Eureme NT SP Écificatio NS Concer Nant LES Pannea UX D’ AF Fleurement Panneaux DE POR TE D’AFFL EUR EmentPanneaux DE Gril LE D’A FFL EUR EM EN T Panneaux D’AFFLEU REM EN T DE Grill E do UB LESInstall Ation S Conjoin TES PO SE DES Panne AUX DE CÔ TÉPO SE DES Panne AUX DE CÔ TÉ PA Nneaux DE CÔ TÉ EN BoisPO UR TE Rmine R L’INSTALLATIO N LIS TE DE CO Ntrôl EDE L’INSTA LLA TI on Liste DE CO NTR ÔLE DE L’INSTA LLA TionSER Vice Aprè S-V Ente SER Vice Aprè S-V EnteFrigo RIF ERI DA in Casso SUB -Z ER O INS Talla Zione DA IncassoAttrez ZI E Mater IAL E Richie STI Prepar Azio NE DE L SIT OSP Ecifiche PE R L’INSTALLAZI ONE DA Incasso DIM Ensio NI GE NER ALISpecifiche PE R L’I NSTAL- Lazione SP Azio PortaModello ICBBI-30U Modello ICBBI-30U Modello ICBBI-30UGModello ICBBI-36U Modello ICBBI-36UG Modello ICBBI-30U 749 mm 813 mmModello ICBBI-36S Modello ICBBI-42S Modello ICBBI-42SDModello ICBBI-36S 902 mm 965 mm Modello ICBBI-48S Modello ICBBI-48SDPE R L’INSTALLAZI ONE DA Incasso REQ Uisiti Elett RiciCollegam Ento ID Rico Disi Mballa Ggio DEL L’U NitàIs TR Uzioni PER L’INST Allaz Ione DA Inca SSO RI MOZ IO NE DE LL a GrigliaInstal LA ZIO NE Della BA RRA Antir Ibal TAM Ento Appli Cazio NE PE R PA VIM Enti in LegnoMI Nuteria ANT IRI Baltamen to in Dotazione Is TR Uzion I PER L Installa Zion E DA Inca SSOInstallaz IO NE DEI Tasselli PER Cemento Installa Zione DE I Pannelli a SO Vrap PO Sizio NE LIV Ellam Ento DE LL’UNIT ÀStalla Zion E Dello Zocc OLO Pannel LO a SO VR AP Posizio NEMonta GG IO DEL PAN NE LL O CO N Grigli a Stalla Zion E DEI Pann Elli a Sovr AP Posi ZIO NEMO Delli CON ERO Gato RE E Vano Bicchier E SP Ecifiche Panne LLI a Sovr APP Osizi ONE Stalla Zion E DEI Pann Elli CON Inserto a FI LO Pannelli conInserti a filo Pannelli con inserti a filoSP Ecifiche DEL Pannello CON Inserti a FI LO Pannelli PE R Porta CON Inse RTO a FiloPannelli GR IGL IA CON INS ER to a Filo Pannelli CON Inser to a FIL O CON Gliglia DoppiaInstall AZ IO NI DOP PIE Stalla Zion E DEI Pann Elli Latera LIStalla Zion E DEI Pann Elli Latera LI PA Nnelli Late Rali in LegnoCOM Plet Amento DELL’INSTALLA ZI ONE Regol Azio NE Inte RNO/ESTERNOREG Olaz IO NE CO N SPO Stame NTO Latera LE REG Olaz IO NE DELL’ALTEZ ZA PO RTEInform Azio NI SU L SER Vizio DI Assi Stenz a CHE Cklist DI Installazio NECheck LI ST DI Installaz IO NE SU B-ZE RO Einb AUK Ühltechn IK EIN BA Uinst AL Lati onErfo RD Erli CHE WE RK ZE UGE UND Material IE N Vorb ER EIT UNG DES INS TA LL AT ION S- OrtesTechnische Daten ZUR Einb AUI Nsta LLA TIO N GE Samt Abmessu NG ENTech NIS CHE DA TE N ZUR Stalla TI on Türf Reirau MTechnische Date N ZUR Einb AU Inst Allat ION Gesam TAB Messung ENTechnis CH E Date N ZUR Stalla TionTechnische Date N ZUR EI NB Auinstallati on Gesam Tabme SSU NGE NTÜ RF REI RAU M TEC Hnis CHE DA TE N ZURAuspa CKE N DES GER ÄTS AN Weisungen ZUR Einbauinsta Llat IONElekt RO VOR Auss Etzunge N AU Sbaue N DES GIT Ters Stal LAT ION DER KIP Pschut Zhal TER UNGHolzb ODE Naus FÜH RU Ngen Beton Bode NA Nwen DU NgenBeto Nank ER KE ILE Installie REN Stallatio N DER Kippsch Utzhal TER UNGBefestigung Steile FÜR KI Ppschutz Inbegriffen Posi Tionie RE N DES GE RÄT SVerkle Idungsp Latten NI Vellier EN DE S Gerä TSStallatio N DER Sockellei STE GI Tterp Latt EN BAU GR UPP E Stallatio N DER Verkleidung Spla TTEGL Asbe TT SPE Nder Modelle Technische Date N ZU VER KLE Idungsp Latte N Verkle Idungstür Platte NVER KLE ID UNG ST ÜR PLA Tten Verkl EID UNG SG IT Terp Latt ENBÜ NDIGE/VO LL Integrie RTE Plat Teni Nsta LLA TI on BÜ NDIGE/VO LL Integrie RTE Plat TENGitterp Latten Baugru PPE BündigeTechnische Date N ZU Bündi GEN/VOLL Integ RI ERT EN Platten Stallatio N DER Seitenpla TTE Stallatio N DER Seitenpla TTESE Itenpl Atten AUS HOL Z DOP Pelinst Allatio NENAbschluss DER Installation SER Vicein for Mation EN Stallatio NschecklisteInstallatio Nsche CK Liste SUB -Z ERO , INC
Related manuals
Manual 69 pages 3.33 Kb

ICBBI-36RG, ICBBI-36F, ICBBI-36R specifications

The Sub-Zero ICBBI-36R, ICBBI-36F, and ICBBI-36RG are premium built-in refrigerators designed to combine cutting-edge technology with sophisticated aesthetics, making them a perfect addition to any modern kitchen. These models stand out for their impressive capacity, advanced features, and customizable design, ensuring they meet the needs of discerning homeowners and culinary enthusiasts alike.

One of the main features of these refrigerators is their dual refrigeration system. By maintaining separate cooling environments for the refrigerator and freezer compartments, Sub-Zero ensures optimal freshness and preservation of food. This technology helps to reduce the chances of odor transfer between compartments, allowing fruits, vegetables, and other perishables to maintain their flavor and nutritional value for longer periods.

The ICBBI-36R model is designed specifically for refrigeration, while the ICBBI-36F focuses on freezing, and the ICBBI-36RG seamlessly combines both. Each unit provides ample storage space, enhancing functionality without compromising on style. The sleek stainless-steel finish and customizable panels enable integration into any kitchen decor, creating a streamlined appearance that suits high-end designs.

Temperature management is a standout characteristic of these units. Sub-Zero refrigerators are equipped with advanced microprocessor controls that monitor and adjust temperatures to ensure optimal conditions for every type of food. The units also feature air purification systems that filter out contaminants and ethylene gas, which can cause fruits and vegetables to ripen too quickly.

Energy efficiency is another critical consideration in these models. Sub-Zero has incorporated energy-saving technologies that meet stringent efficiency guidelines while still delivering superior cooling performance. These refrigerators use less energy than traditional models, aligning with modern consumers' growing interest in sustainability.

Furthermore, the ICBBI-36 line includes various features designed for convenience, such as adjustable shelving and storage bins, providing ease of organization. The door panel ice maker and water dispenser in the ICBBI-36RG model add an extra layer of convenience for users.

Overall, the Sub-Zero ICBBI-36R, ICBBI-36F, and ICBBI-36RG embody a perfect blend of innovation, style, and functionality. With advanced refrigeration technologies, customizable design, and energy efficiency, these models offer a top-tier solution for preserving food while elevating kitchen aesthetics.
Top Page Image Contents