Sub-Zero 427RG, 427G manual Models 424G and 424FSG Installation Position the Unit

Page 10

Models 424G and 424FSG Installation

10

 

 

Position the Unit

If you are adding an accessory lock kit to your wine storage unit, it should be installed before you position the unit. The accessory lock kit and additional instructions are available through your authorized Sub-Zero dealer, or call Sub-Zero at 800-222-7820. You can also visit our website at subzero.com.

IMPORTANT NOTE: If for any reason the wine storage unit has been laid on its back or side, you must allow the unit to stand upright for a minimum of 24 hours before con- necting power.

Plug the power cord into the grounded electrical outlet. With power applied to the appliance, check for lighting and cooling before going any further. Once you are satis- fied that the unit is operating properly, shut off power to the electrical outlet at the circuit breaker and proceed.

Pre-level the wine storage unit before sliding it into position. Leveling cannot be completed with the unit pushed back in the installation opening.

If a home alarm system is to be used with the wine storage unit, the lead wires should be threaded into the compressor compartment before you position the unit. Refer to home alarm connections on the following page, for the location of these lead wires. After the unit is in position, the alarm wiring can be completed from the front.

For model 424FSG, adust the leveling legs so the top of the unit is no more than 345/8" (879) above the floor. This is to allow the unit to engage the anti-tip bracket properly. Center the model 424FSG in front of the anti-tip bracket.

Slide the unit into position, making sure the anti-tip bracket is engaged properly.

When the wine storage unit is installed, the anti-tip bracket will be positioned just below the engaging bracket on the unit. It is not necessary to raise the unit up so that it locks into the anti-tip bracket, but the unit must be in alignment with the anti-tip bracket.

The wine storage unit provides the best access to its contents when the front surface of the door panel extends out from surrounding cabinets approximately 1/4" (6). For model 424FSG, if there are no surrounding cabinet surfaces to gauge depth, slide the unit back until it engages the anti-tip bracket.

IMPORTANT NOTE: The floor under the wine storage unit must be at the same level as the surrounding finished floor to allow for removal of the unit for servicing.

Image 10
Contents Wine Storage Contents Important NoteWine Storage Sub-Zero Wine Storage Subzero.comModels 424G and 424FSG Installation Overall DimensionsOpening Dimensions Tools and Materials RequiredModels 424G and 424FSG Installation Electrical Requirements Electrical RequirementsHome Alarm System Moving the UnitModel 424G Model 424FSGModel 424FSG-WOOD Floors Install Concrete Wedge AnchorsModel 424FSG-CONCRETE Floors Models 424G and 424FSG Installation Position the Unit Models 424G and 424FSG Installation Level the Unit Home Alarm ConnectionsModels 424G and 424FSG Installation Kickplate Installation Door PanelModels 424G and 424FSG Installation Overlay Door Panel Models 424G and 424FSG Installation Overlay Door Panel Models 424G and 424FSG Installation Hinge Adjustment Complete the InstallationModels 427G and 427RG Installation Tools and Materials Required Opening Dimensions Models 427G and 427RG Installation Electrical Requirements Anti-Tip Bracket Installation Wood Floor Applications Concrete Floor ApplicationsLock Installation Dual InstallationsUnpack the Unit Models 427G and 427RG Installation Position the Unit Models 427G and 427RG Installation Level the Unit Molding InstallationModels 427G and 427RG Installation Wiring Connections Door Panels Stainless steel panel Overlay panel Models 427G and 427RG Installation Overlay Door Panel Models 427G and 427RG Installation Drawer Panel Installation Model 427RGAnchoring Models 427G and 427RG Installation Side PanelsInstallation Checklist Optional 90 Door StopModel WS-30 Installation Model WS-30 Installation Site Preparation Framed, Overlay and Stainless Steel Models Flush Inset Installation Opening Dimensions Detail aOpening Widths Dual Flush Inset Installation Opening Dimensions 263/16Model WS-30 Installation Electrical Requirements Model WS-30 Installation Anti-Tip Bracket Installation Anti-Tip Bracket HardwareFloor Grille Height Adjustment Model WS-30 Installation Unpack the UnitGrille Removal Model WS-30 Installation Position the Unit Side to Side Tilt Adjustment Model WS-30 Installation Door AdjustmentOUT Adjustment Door Height AdjustmentModel WS-30 Installation Panel Installation Install Kickplate Model WS-30 Installation Framed Panel Framed Panel InstallationFramed Panel Specifications Raised PanelModel WS-30 Installation Overlay Panels Overlay Panel Specifications Grille Panel AssemblyModel WS-30 Installation Flush Inset Panels Flush Inset Panel Specifications Dual Installations Model WS-30 Installation Flush Inset PanelDual Standard Installations Flush Inset Panels-Dual Installation Dual Flush Inset InstallationsOpposite hinges Model WS-30 Installation Side Panels Custom Side Panel InstallationInstallation Checklist Service Information SUB-ZERO, INC. P. O. BOX 44848 MADISON, WI 53744 SUBZERO.COM
Related manuals
Manual 2 pages 3.57 Kb

424G, 424FSG, 427G, 427RG specifications

Sub-Zero has long been synonymous with premium refrigeration technology, and their models 427RG, 427G, 424FSG, and 424G exemplify this legacy of excellence. These refrigerators are designed for culinary enthusiasts, offering both unparalleled performance and sophisticated design.

The Sub-Zero 427RG and 427G are part of the brand's 400 series, known for their dual refrigeration systems. This technology utilizes separate cooling systems for the refrigerator and freezer compartments, which helps maintain optimal humidity levels and prevents the transfer of odors. The models feature advanced air purification systems that continuously filter and circulate air, ensuring that food stays fresher for longer. Additionally, the 427RG model comes with a glass door option, providing visibility to its premium contents while adding a stunning aesthetic to any kitchen.

In terms of storage, both 427RG and 427G models offer ample capacity with adjustable shelves and customizable bin configurations. The shelving is crafted from elegant glass, which adds a touch of sophistication. With features such as a niche drawer for fresh produce, users can easily organize their groceries while maximizing space efficiency.

The Sub-Zero 424FSG and 424G models are similarly impressive, though they come with their own set of unique features. The 424FSG, for instance, includes a full-width freezer drawer, equipped with an ice maker and ample storage space, making it ideal for those who require extra freezing capacity. The 424G, on the other hand, seamlessly integrates a clean, modern design with robust functionality. Both models benefit from an intuitive touch control system that allows for precise temperature adjustments, alongside soft-close drawers that enhance user convenience and reduce wear.

Energy efficiency is another hallmark of Sub-Zero’s design philosophy. All four models are ENERGY STAR rated, combining performance with environmentally conscious technology. This commitment to quality and sustainability extends to their use of durable materials and craftsmanship, ensuring longevity and reliability for years to come.

Whether you choose the sleek sophistication of the 427RG and 427G or the functional elegance of the 424FSG and 424G, Sub-Zero offers a refrigeration solution that balances innovation with traditional craftsmanship. These refrigerators are not just appliances; they are an investment in kitchen sophistication and food preservation excellence. With their state-of-the-art features, these models exemplify how Sub-Zero remains at the forefront of luxury refrigeration.