Dacor EF36RNBSS Level and Align Refrigerator, After moving the refrigerator to its final location

Page 18

Installation Instructions

Level and Align Refrigerator

WARNING

Tip Over Hazard

Refrigerator is top heavy and tips easily when not completely installed.

Keep doors taped closed until refrigerator is completely installed.

Use two or more people to move and install refrigerator.

Failure to do so can result in death or serious injury.

IMPORTANT: All four leveling legs must contact the floor to support and stabilize the full weight of refrigerator. Rollers are for moving refrigerator and not for permanent support.

After moving the refrigerator to its final location:

1.Use a 516” socket driver to turn the leveling bolts clockwise to extend the legs to the floor as shown. The rollers should be off the floor.

A B

A

B

A. Rear leveling bolt

B. Front leveling bolt

2.Adjust the leveling legs to level and align the refrigerator from left to right and front to back so that the refrigerator is level and aligned with the cabinets. The cabinet surface must be plumb for the ideal fit of the refrigerator side trim.

3.Continue adjusting all of the leveling legs to raise the refrigerator until the top is within at least 1” (2.54 cm) of the top soffit.

NOTE: If an anti-tip board has been used, adjust the leveling legs until the top of the refrigerator is within ¼” (6.35 mm) of the bottom of the anti-tip board as shown. Do not crush the compressor cover.

A B

C

2" (5 cm)

D

A. Center board ¼ " (6.35 mm) max. above refrigerator B. Two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) boards C. Attach to studs with six #8 x 3" (7.6 cm) screws

D. Compressor cover

IMPORTANT: Adjust in small increments to keep from damaging the cabinet trim and causing problems with the door alignment or top grille fit. To avoid damage to the cabinet or leveling legs, do not apply more than 50 inch-pounds (5.65 Nm) of torque to the leveling bolts. The leveling legs can be extended to a maximum of 1¼” (3.18 cm) below the rollers.

4.For IF series models, additional adjustments may be needed after the custom panels are installed.

16

Image 18
Contents Installation Instructions Inch Built-In Refrigerator Table of Contents Customer Service InformationRefrigerator Safety Model Identification EF36LNBSSTools and Parts Installation RequirementsOpening Dimensions Location RequirementsElectrical Requirements Location RequirementsRecommended Grounding Method Water Pressure Water Supply RequirementsTipping Radius Side Tipping RadiusSide View Product DimensionsDoor Swing Dimensions Top ViewDoor Panels and Cabinet Clearance IF36 Series Models Door Swing Actual Size Refrigerator to Cabinet ClearanceDoor Swing 90 Actual Size Refrigerator to Cabinet Clearance AnelInstall the panels after moving the refrigerator into place Weight of the overlay panels cannot exceedCustom Panels and Handles IF36 Series Models Piece Overlay Panel Configuration Piece Grille Overlay Panel ConfigurationPiece Door Overlay Panel Configuration Custom Panels Construction InformationRecessed Inset Installation Dimensions Refrigerator and Side Trim DimensionsInset Installation Dimensions Custom Side Panels Model IF36Back Wall Refrigerator Flush Installation DimensionsCustom Side Panels Model EF36 BackReduce Tipping Radius Installation InstructionsUnpack the Refrigerator Move Refrigerator into HouseStyle 1 Shutoff Valve Connection Install Anti-Tip BoardsConnect the Water Supply Style 2 Copper Line ConnectionConnecting to Refrigerator Plug in RefrigeratorMove to Final Location Level and Align Refrigerator After moving the refrigerator to its final locationCustom Panel and Handle Installation IF36 Series Models Handle InstallationDoor Panel Installation Door Swing Adjustment Adjust DoorsCustom Panel Installation IF36 Series Models Door-to-Door or Door-to-Refrigerator Trim AdjustmentInstall Side Panels Install Base GrilleComplete Installation Water System PreparationInstructions d’installation Réfrigérateur Encastré de Information pour le service à la clientèle Exigences d’installationSécurité du réfrigérateur Identification des modèles Dimensions de l’ouverture Exigences d’installationExigences d’emplacement Outillage et composantsExigences d’emplacement suite Méthode recommandée de liaison à la terreSpécifications électriques Pression de l’eau Rayon de basculementExigences de l’alimentation en eau Rayon de basculement latéralVue latérale Dimensions du produitDimensions pour le pivotement des portes Vue avantDégagement Réfrigérateur/placard Position de butée 110˚Pivotement à 90 Dimensions réelles Panneau décoratifs Dimensions Panneau d’appui Dimensions Panneaux et poignées personnalisés modèle de la série IF36Information sur la construction des panneaux personnalisés Poignées personnalisésDimensions pour une installation en encastrement en retrait Dimensions du réfrigérateur et des garnitures latéralesDimensions pour une installation en encastrement Panneaux latéraux personnalisés modèle IF36Dimensions pour une installation en affleurement Faire entrer le réfrigérateur dans le domicile Instructions d’installationDéballage du réfrigérateur Réduction du rayon de basculement si nécessaireInstallation de planches antibasculement Installation de planches antibasculementRaccordement à la canalisation d’eau Brancher le réfrigérateur Raccordement au réfrigérateurRéglage de l’aplomb et alignement du réfrigérateur Installation de la poignée Installation du panneau de porteRéglage des portes Panneau de la grille supérieureRéglage de l’angle d’ouverture de la porte Installation des panneaux latéraux Installation de la grille de la baseAchever l’installation Préparation du système d’eauPage Page