Dacor EF36RNBSS Electrical Requirements, Location Requirements, Recommended Grounding Method

Page 6

Installation Requirements

Location Requirements (continued)

ƒƒ A grounded 3 prong electrical outlet should be placed within 4” (10.2 cm) of the right side cabinets or end panel. See Electrical Requirements for more information.

ƒƒ The water shutoff should be located in the base cabinet on either side of the refrigerator or some other easily accessible area. If the water shutoff valve is not in the cabinets, the plumbing for the water line can come through the floor or the back wall. See Water Supply Requirements for more information.

Electrical Requirements

Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical connection.

WARNING

4"

(10.2 cm)

83¹/2" (212.1 cm) min.

84³/4" (215 cm) max.

to bottom of solid soffit

77"

(196 cm)

35½”

(90.2 cm)

24"

(60.96 cm) min.

See page 5

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

Recommended Grounding Method

A 115 Volt, 60 Hz., AC only 15 or 20-amp fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your refrigerator be provided. Use an outlet that cannot be turned off by a switch. Do not use an extension cord.

IMPORTANT: If this product is connected to a GFCI (Ground Fault Circuit Interrupter) protected outlet, nuisance tripping of the power supply may occur, resulting in loss of cooling. Food quality and flavor may be affected. If nuisance tripping has occurred, and if the condition of the food appears poor, dispose of it.

NOTE: Before performing any type of installation, cleaning, or removing a light bulb, remove the top grille and turn the master power switch to OFF or disconnect power at the circuit breaker box.

When you are finished, turn on the master power switch or reconnect power at the circuit breaker box. Then reset the control to the desired setting.

NOTE: Flooring under refrigerator must be at same level as the room. Face of cabinet must be plumb.

4

Image 6
Contents Installation Instructions Inch Built-In Refrigerator Table of Contents Customer Service InformationRefrigerator Safety Model Identification EF36LNBSSTools and Parts Installation RequirementsOpening Dimensions Location RequirementsElectrical Requirements Location RequirementsRecommended Grounding Method Water Pressure Water Supply RequirementsTipping Radius Side Tipping RadiusSide View Product DimensionsDoor Swing Dimensions Top ViewDoor Panels and Cabinet Clearance IF36 Series Models Door Swing Actual Size Refrigerator to Cabinet ClearanceDoor Swing 90 Actual Size Refrigerator to Cabinet Clearance AnelInstall the panels after moving the refrigerator into place Weight of the overlay panels cannot exceedCustom Panels and Handles IF36 Series Models Piece Overlay Panel Configuration Piece Grille Overlay Panel ConfigurationPiece Door Overlay Panel Configuration Custom Panels Construction InformationRecessed Inset Installation Dimensions Refrigerator and Side Trim DimensionsInset Installation Dimensions Custom Side Panels Model IF36Back Wall Refrigerator Flush Installation DimensionsCustom Side Panels Model EF36 BackReduce Tipping Radius Installation InstructionsUnpack the Refrigerator Move Refrigerator into HouseStyle 1 Shutoff Valve Connection Install Anti-Tip BoardsConnect the Water Supply Style 2 Copper Line ConnectionConnecting to Refrigerator Plug in RefrigeratorMove to Final Location Level and Align Refrigerator After moving the refrigerator to its final locationCustom Panel and Handle Installation IF36 Series Models Handle InstallationDoor Panel Installation Door Swing Adjustment Adjust DoorsCustom Panel Installation IF36 Series Models Door-to-Door or Door-to-Refrigerator Trim AdjustmentInstall Side Panels Install Base GrilleComplete Installation Water System PreparationInstructions d’installation Réfrigérateur Encastré de Information pour le service à la clientèle Exigences d’installationSécurité du réfrigérateur Identification des modèles Dimensions de l’ouverture Exigences d’installationExigences d’emplacement Outillage et composantsExigences d’emplacement suite Méthode recommandée de liaison à la terreSpécifications électriques Pression de l’eau Rayon de basculementExigences de l’alimentation en eau Rayon de basculement latéralVue latérale Dimensions du produitDimensions pour le pivotement des portes Vue avantDégagement Réfrigérateur/placard Position de butée 110˚Pivotement à 90 Dimensions réelles Panneau décoratifs Dimensions Panneau d’appui Dimensions Panneaux et poignées personnalisés modèle de la série IF36Information sur la construction des panneaux personnalisés Poignées personnalisésDimensions pour une installation en encastrement en retrait Dimensions du réfrigérateur et des garnitures latéralesDimensions pour une installation en encastrement Panneaux latéraux personnalisés modèle IF36Dimensions pour une installation en affleurement Faire entrer le réfrigérateur dans le domicile Instructions d’installationDéballage du réfrigérateur Réduction du rayon de basculement si nécessaireInstallation de planches antibasculement Installation de planches antibasculementRaccordement à la canalisation d’eau Brancher le réfrigérateur Raccordement au réfrigérateurRéglage de l’aplomb et alignement du réfrigérateur Installation de la poignée Installation du panneau de porteRéglage des portes Panneau de la grille supérieureRéglage de l’angle d’ouverture de la porte Installation des panneaux latéraux Installation de la grille de la baseAchever l’installation Préparation du système d’eauPage Page